78 lines
2.7 KiB
INI
78 lines
2.7 KiB
INI
# NXP LPC1754 Cortex-M3 with 128kB Flash and 16kB+16kB Local On-Chip SRAM,
|
|
# reset_config trst_and_srst
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME lpc1754
|
|
}
|
|
|
|
# After reset the chip is clocked by the ~4MHz internal RC oscillator.
|
|
# When board-specific code (reset-init handler or device firmware)
|
|
# configures another oscillator and/or PLL0, set CCLK to match; if
|
|
# you don't, then flash erase and write operations may misbehave.
|
|
# (The ROM code doing those updates cares about core clock speed...)
|
|
#
|
|
# CCLK is the core clock frequency in KHz
|
|
if { [info exists CCLK ] } {
|
|
set _CCLK $CCLK
|
|
} else {
|
|
set _CCLK 4000
|
|
}
|
|
if { [info exists CPUTAPID ] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x4ba00477
|
|
}
|
|
|
|
#delays on reset lines
|
|
#if your OpenOCD version rejects "jtag_nsrst_delay" replace it with:
|
|
#adapter_nsrst_delay 200
|
|
jtag_nsrst_delay 200
|
|
jtag_ntrst_delay 200
|
|
|
|
# LPC2000 & LPC1700 -> SRST causes TRST
|
|
#reset_config srst_pulls_trst
|
|
reset_config trst_and_srst srst_push_pull trst_push_pull
|
|
|
|
jtag newtap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
|
|
#jtag newtap x3s tap -irlen 6 -ircapture 0x11 -irmask 0x11 -expected-id 0x0141c093
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m3 -chain-position $_TARGETNAME -event reset-init 0
|
|
|
|
# LPC1754 has 16kB of SRAM In the ARMv7-M "Code" area (at 0x10000000)
|
|
# and 16K more on AHB, in the ARMv7-M "SRAM" area, (at 0x2007c000).
|
|
$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size 0x4000
|
|
$_TARGETNAME configure -work-area-phys 0x2007c000 -work-area-size 0x4000
|
|
|
|
# LPC1754 has 128kB of flash memory, managed by ROM code (including a
|
|
# boot loader which verifies the flash exception table's checksum).
|
|
# flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum]
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME lpc2000 0x0 0x20000 0 0 $_TARGETNAME \
|
|
lpc1700 $_CCLK calc_checksum
|
|
|
|
# Run with *real slow* clock by default since the
|
|
# boot rom could have been playing with the PLL, so
|
|
# we have no idea what clock the target is running at.
|
|
jtag_khz 1000
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select
|
|
# "User Flash Mode" where interrupt vectors are _not_ remapped,
|
|
# and reside in flash instead).
|
|
#
|
|
# See Table 612. Memory Mapping Control register (MEMMAP - 0x400F C040) bit description
|
|
# Bit Symbol Value Description Reset
|
|
# value
|
|
# 0 MAP Memory map control. 0
|
|
# 0 Boot mode. A portion of the Boot ROM is mapped to address 0.
|
|
# 1 User mode. The on-chip Flash memory is mapped to address 0.
|
|
# 31:1 - Reserved. The value read from a reserved bit is not defined. NA
|
|
#
|
|
# http://ics.nxp.com/support/documents/microcontrollers/?scope=LPC1768&type=user
|
|
|
|
mww 0x400FC040 0x01
|
|
}
|