Make bootloader 1 work

usb bulk transfers copy the last byte of the chunk to SRAM twice.

.ditz-config

@@ -1,4 +0,0 @@
---- !ditz.rubyforge.org,2008-03-06/config 
-name: David
-email: david@optixx.org
-issue_dir: bugs

.gitignore

@@ -27,3 +27,17 @@
 *.vfat
 *.wla*
 *.rcc
+*.log
+bootloader
+snesuploader
+tmtags
+bsnes
+web
+ucon64.exe
+project
+huffman-decode
+huffman-encode
+unpack
+pack
+
+

README.md

@@ -0,0 +1,11 @@
+ ```
+  ________        .__        __    ________               ____  ________
+  \_____  \  __ __|__| ____ |  | __\______ \   _______  _/_   |/  _____/
+   /  / \  \|  |  \  |/ ___\|  |/ / |    |  \_/ __ \  \/ /|   /   __  \
+  /   \_/.  \  |  /  \  \___|    <  |    `   \  ___/\   / |   \  |__\  \
+  \_____\ \_/____/|__|\___  >__|_ \/_______  /\___  >\_/  |___|\_____  /
+         \__>             \/     \/        \/     \/                 \/
+ 
+ ```
+[Go to the Documentation](../../wiki)
+

avr/bootloader/avr.mk

@@ -67,7 +67,7 @@ clean:
 
 .PHONY: all clean interactive-isp interactive-serial launch-bootloader
 
-flash: 
+flash: bootloader.hex
 	$(AVRDUDE) $(AVRDUDE_FLAGS) -c $(ISP_PROG) -U flash:w:$<
 
 flash-eeprom-%: %.eep.hex

avr/bootloader/bootloader.c

@@ -33,6 +33,10 @@
 #include "config.h"
 #include "usbdrv/usbdrv.c"
 
+
+
+
+
 /*
  * USBasp requests, taken from the original USBasp sourcecode 
  */
@@ -74,8 +78,12 @@
                   (LED_DIR ^= (1 << LED_PIN)));}
 
 
+#define AVR_BTLDR_EN_PORT	    PORTC
+#define AVR_BTLDR_EN_DIR	    DDRC
+#define AVR_BTLDR_EN_PIN	    PC1
+#define AVR_BTLDR_EN_IN	        PINC
 
-
+#undef AVR_BTLDR_SWITCH
 /*
  * some predefined signatures, taken from the original USBasp sourcecode 
  */
@@ -286,7 +294,7 @@ usbMsgLen_t usbFunctionSetup(uchar data[8])
                 boot_page_erase(flash_address.word);
                 sei();
             }
-            uart_puts("\n\r");
+            uart_puts("\n\rWrite Flash");
         }
 
         /*
@@ -406,9 +414,10 @@ void leave_bootloader(void)
      * disconnect usb 
      */
     usbDeviceDisconnect();
+#if 0    
     for (uint8_t i = 0; i < 50; i++)
         _delay_ms(10);          /* 0 means 0x10000, 38*1/f*0x10000 =~ 498ms */
-
+#endif
     /*
      * enable watchdog to soft-reset the uC for clean startup of new application 
      */
@@ -421,6 +430,13 @@ void leave_bootloader(void)
 
 }
 
+void banner(){
+    uart_puts("\n\r");
+    uart_puts("\n\r");
+    uart_puts("\n\r");
+    uart_puts("Quickdev16 Bootloader v0.2\n\r"); 
+    uart_puts("www.optixx.org\n\r");
+}
 
 int __attribute__ ((noreturn, OS_main)) main(void)
 {
@@ -441,32 +457,39 @@ int __attribute__ ((noreturn, OS_main)) main(void)
     uint16_t delay = 0;
     timeout = TIMEOUT;
 
-    uart_puts("Snesram Bootloader v0.1\n\r");
+    DDRC &= ~(1 << AVR_BTLDR_EN_PIN);	    
+    PORTC &= ~(1 << AVR_BTLDR_EN_PIN);	    
+
+    /*
+     * if watchdog reset, disable watchdog and jump to app 
+     */
+    if (reset & _BV(WDRF)) {
+        uart_puts("Found watchdog reset\n\r");
+        MCUSR = 0;
+        wdt_disable();
+        uart_puts("Jump to 0x0000\n\r");
+        jump_to_app();
+    }
+
+#if AVR_BTLDR_SWITCH_ENABLE
+    if ((AVR_BTLDR_EN_IN & ( 1 << AVR_BTLDR_EN_PIN)) == 0){
+        banner();
+        uart_puts("Bootloader flashing is disabled\n\r");
+        MCUSR = 0;
+        leave_bootloader();
+    }
+#endif
 
     /*
      * if power-on reset, quit bootloader via watchdog reset 
      */
     if (reset & _BV(PORF)) {
+        banner();
         uart_puts("Found power on reset\n\r");
         MCUSR = 0;
         leave_bootloader();
     }
-    /*
+    banner();
-     * if watchdog reset, disable watchdog and jump to app 
-     */
-    else if (reset & _BV(WDRF)) {
-        uart_puts("Found watchdog reset\n\r");
-        MCUSR = 0;
-        wdt_disable();
-        DLED_TGL;
-        _delay_ms(500);
-        DLED_TGL;
-        _delay_ms(500);
-        uart_puts("Jump to main\n\r");
-        jump_to_app();
-    }
-
-
     uart_puts("Enter programming mode\n\r");
     /*
      * else: enter programming mode 

avr/bootloader/config.h

@@ -20,3 +20,4 @@
 
 #define DEBUG                       1
 #define DEBUG_USB                   2
+#define AVR_BTLDR_SWITCH_ENABLE     1

avr/bootloader/usbdrv/Changelog.txt

@@ -231,3 +231,99 @@ Scroll down to the bottom to see the most recent changes.
   - Added 20 MHz module contributed by Jeroen Benschop.
 
 * Release 2008-05-13
+
+  - Fixed bug in libs-host/hiddata.c function usbhidGetReport(): length
+    was not incremented, pointer to length was incremented instead.
+  - Added code to command line tool(s) which claims an interface. This code
+    is disabled by default, but may be necessary on newer Linux kernels.
+  - Added usbconfig.h option "USB_CFG_CHECK_DATA_TOGGLING".
+  - New header "usbportability.h" prepares ports to other development
+    environments.
+  - Long transfers (above 254 bytes) did not work when usbFunctionRead() was
+    used to supply the data. Fixed this bug. [Thanks to Alexander Neumann!]
+  - In hiddata.c (example code for sending/receiving data over HID), use
+    USB_RECIP_DEVICE instead of USB_RECIP_INTERFACE for control transfers so
+    that we need not claim the interface.
+  - in usbPoll() loop 20 times polling for RESET state instead of 10 times.
+    This accounts for the higher clock rates we now support.
+  - Added a module for 12.8 MHz RC oscillator with PLL in receiver loop.
+  - Added hook to SOF code so that oscillator can be tuned to USB frame clock.
+  - Added timeout to waitForJ loop. Helps preventing unexpected hangs.
+  - Added example code for oscillator tuning to libs-device (thanks to
+    Henrik Haftmann for the idea to this routine).
+  - Implemented option USB_CFG_SUPPRESS_INTR_CODE.
+
+* Release 2008-10-22
+
+  - Fixed libs-device/osctune.h: OSCCAL is memory address on ATMega88 and
+    similar, not offset of 0x20 needs to be added.
+  - Allow distribution under GPLv3 for those who have to link against other
+    code distributed under GPLv3.
+
+* Release 2008-11-26
+
+  - Removed libusb-win32 dependency for hid-data example in Makefile.windows.
+    It was never required and confused many people.
+  - Added extern uchar usbRxToken to usbdrv.h.
+  - Integrated a module with CRC checks at 18 MHz by Lukas Schrittwieser.
+
+* Release 2009-03-23
+
+  - Hid-mouse example used settings from hid-data example, fixed that.
+  - Renamed project to V-USB due to a trademark issue with Atmel(r).
+  - Changed CommercialLicense.txt and USBID-License.txt to make the
+    background of USB ID registration clearer.
+
+* Release 2009-04-15
+
+  - Changed CommercialLicense.txt to reflect the new range of PIDs from
+    Jason Kotzin.
+  - Removed USBID-License.txt in favor of USB-IDs-for-free.txt and
+    USB-ID-FAQ.txt
+  - Fixed a bug in the 12.8 MHz module: End Of Packet decection was made in
+    the center between bit 0 and 1 of each byte. This is where the data lines
+    are expected to change and the sampled data may therefore be nonsense.
+    We therefore check EOP ONLY if bits 0 AND 1 have both been read as 0 on D-.
+  - Fixed a bitstuffing problem in the 16 MHz module: If bit 6 was stuffed,
+    the unstuffing code in the receiver routine was 1 cycle too long. If
+    multiple bytes had the unstuffing in bit 6, the error summed up until the
+    receiver was out of sync.
+  - Included option for faster CRC routine.
+    Thanks to Slawomir Fras (BoskiDialer) for this code!
+  - Updated bits in Configuration Descriptor's bmAttributes according to
+    USB 1.1 (in particular bit 7, it is a must-be-set bit now).
+
+* Release 2009-08-22
+
+  - Moved first DBG1() after odDebugInit() in all examples.
+  - Use vector INT0_vect instead of SIG_INTERRUPT0 if defined. This makes
+    V-USB compatible with the new "p" suffix devices (e.g. ATMega328p).
+  - USB_CFG_CLOCK_KHZ setting is now required in usbconfig.h (no default any
+    more).
+  - New option USB_CFG_DRIVER_FLASH_PAGE allows boot loaders on devices with
+    more than 64 kB flash.
+  - Built-in configuration descriptor allows custom definition for second
+    endpoint now.
+
+* Release 2010-07-15
+
+  - Fixed bug in usbDriverSetup() which prevented descriptor sizes above 255
+    bytes.
+  - Avoid a compiler warning for unused parameter in usbHandleResetHook() when
+    compiler option -Wextra is enabled.
+  - Fixed wrong hex value for some IDs in USB-IDs-for-free.txt.
+  - Keep a define for USBATTR_BUSPOWER, although the flag does not exist
+    in USB 1.1 any more. Set it to 0. This is for backward compatibility.
+
+* Release 2012-01-09
+
+  - Define a separate (defined) type for usbMsgPtr so that projects using a
+    tiny memory model can define it to an 8 bit type in usbconfig.h. This
+    change also saves a couple of bytes when using a scalar 16 bit type.
+  - Inserted "const" keyword for all PROGMEM declarations because new GCC
+    requires it.
+  - Fixed problem with dependence of usbportability.h on usbconfig.h. This
+    problem occurred with IAR CC only.
+  - Prepared repository for github.com.
+
+* Release 2012-12-06

avr/bootloader/usbdrv/CommercialLicense.txt

@@ -1,5 +1,5 @@
-AVR-USB Driver Software License Agreement
+V-USB Driver Software License Agreement
-Version 2008-04-15
+Version 2012-07-09
 
 THIS LICENSE AGREEMENT GRANTS YOU CERTAIN RIGHTS IN A SOFTWARE. YOU CAN
 ENTER INTO THIS AGREEMENT AND ACQUIRE THE RIGHTS OUTLINED BELOW BY PAYING
@@ -13,8 +13,8 @@ Grosse Schiffgasse 1A/7, 1020 Wien, AUSTRIA.
 
 1.2 "You" shall mean the Licensee.
 
-1.3 "AVR-USB" shall mean all files included in the package distributed under
+1.3 "V-USB" shall mean all files included in the package distributed under
-the name "avrusb" by OBJECTIVE DEVELOPMENT (http://www.obdev.at/avrusb/)
+the name "vusb" by OBJECTIVE DEVELOPMENT (http://www.obdev.at/vusb/)
 unless otherwise noted. This includes the firmware-only USB device
 implementation for Atmel AVR microcontrollers, some simple device examples
 and host side software examples and libraries.
@@ -23,21 +23,31 @@ and host side software examples and libraries.
 2 LICENSE GRANTS
 
 2.1 Source Code. OBJECTIVE DEVELOPMENT shall furnish you with the source
-code of AVR-USB.
+code of V-USB.
 
 2.2 Distribution and Use. OBJECTIVE DEVELOPMENT grants you the
-non-exclusive right to use and distribute AVR-USB with your hardware
+non-exclusive right to use, copy and distribute V-USB with your hardware
 product(s), restricted by the limitations in section 3 below.
 
 2.3 Modifications. OBJECTIVE DEVELOPMENT grants you the right to modify
-your copy of AVR-USB according to your needs.
+the source code and your copy of V-USB according to your needs.
 
-2.4 USB IDs. OBJECTIVE DEVELOPMENT grants you the exclusive rights to use
+2.4 USB IDs. OBJECTIVE DEVELOPMENT furnishes you with one or two USB
-USB Product ID(s) sent to you in e-mail after receiving your payment in
+Product ID(s), sent to you in e-mail. These Product IDs are reserved
-conjunction with USB Vendor ID 5824. OBJECTIVE DEVELOPMENT has acquired an
+exclusively for you. OBJECTIVE DEVELOPMENT has obtained USB Product ID
-exclusive license for this pair of USB identifiers from Wouter van Ooijen
+ranges under the Vendor ID 5824 from Wouter van Ooijen (Van Ooijen
-(www.voti.nl), who has licensed the VID from the USB Implementers Forum,
+Technische Informatica, www.voti.nl) and under the Vendor ID 8352 from
-Inc. (www.usb.org).
+Jason Kotzin (now flirc.tv, Inc.). Both owners of the Vendor IDs have
+obtained these IDs from the USB Implementers Forum, Inc. (www.usb.org).
+OBJECTIVE DEVELOPMENT disclaims all liability which might arise from the
+assignment of USB IDs.
+
+2.5 USB Certification. Although not part of this agreement, we want to make
+it clear that you cannot become USB certified when you use V-USB or a USB
+Product ID assigned by OBJECTIVE DEVELOPMENT. AVR microcontrollers don't
+meet the electrical specifications required by the USB specification and
+the USB Implementers Forum certifies only members who bought a Vendor ID of
+their own.
 
 
 3 LICENSE RESTRICTIONS
@@ -46,21 +56,21 @@ Inc. (www.usb.org).
 applicable. Which one is determined by the amount you pay to OBJECTIVE
 DEVELOPMENT, see section 4 ("Payment") below.
 
-Hobby License: You may use AVR-USB according to section 2 above in no more
+Hobby License: You may use V-USB according to section 2 above in no more
 than 5 hardware units. These units must not be sold for profit.
 
-Entry Level License: You may use AVR-USB according to section 2 above in no
+Entry Level License: You may use V-USB according to section 2 above in no
 more than 150 hardware units.
 
-Professional License: You may use AVR-USB according to section 2 above in
+Professional License: You may use V-USB according to section 2 above in
 any number of hardware units, except for large scale production ("unlimited
 fair use"). Quantities below 10,000 units are not considered large scale
 production. If your reach quantities which are obviously large scale
 production, you must pay a license fee of 0.10 EUR per unit for all units
 above 10,000.
 
-3.2 Rental. You may not rent, lease, or lend AVR-USB or otherwise encumber
+3.2 Rental. You may not rent, lease, or lend V-USB or otherwise encumber
-any copy of AVR-USB, or any of the rights granted herein.
+any copy of V-USB, or any of the rights granted herein.
 
 3.3 Transfer. You may not transfer your rights under this Agreement to
 another party without OBJECTIVE DEVELOPMENT's prior written consent. If
@@ -78,7 +88,7 @@ non-exclusive.
 by third parties. In particular, you are not allowed to use the USB logo or
 other trademarks owned by the USB Implementers Forum, Inc. without their
 consent. Since such consent depends on USB certification, it should be
-noted that AVR-USB will not pass certification because it does not
+noted that V-USB will not pass certification because it does not
 implement checksum verification and the microcontroller ports do not meet
 the electrical specifications.
 
@@ -88,15 +98,15 @@ the electrical specifications.
 The payment amount depends on the variation of this agreement (according to
 section 3.1) into which you want to enter. Concrete prices are listed on
 OBJECTIVE DEVELOPMENT's web site, usually at
-http://www.obdev.at/avrusb/license.html. You agree to pay the amount listed
+http://www.obdev.at/vusb/license.html. You agree to pay the amount listed
 there to OBJECTIVE DEVELOPMENT or OBJECTIVE DEVELOPMENT's payment processor
 or reseller.
 
 
 5 COPYRIGHT AND OWNERSHIP
 
-AVR-USB is protected by copyright laws and international copyright
+V-USB is protected by copyright laws and international copyright
-treaties, as well as other intellectual property laws and treaties. AVR-USB
+treaties, as well as other intellectual property laws and treaties. V-USB
 is licensed, not sold.
 
 
@@ -112,12 +122,12 @@ and limitation of liability shall survive termination of this agreement.
 
 7 DISCLAIMER OF WARRANTY AND LIABILITY
 
-LIMITED WARRANTY. AVR-USB IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
+LIMITED WARRANTY. V-USB IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
 KIND. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, OBJECTIVE
 DEVELOPMENT AND ITS SUPPLIERS HEREBY DISCLAIM ALL WARRANTIES, EITHER
 EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
 OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND
-NON-INFRINGEMENT, WITH REGARD TO AVR-USB, AND THE PROVISION OF OR FAILURE
+NON-INFRINGEMENT, WITH REGARD TO V-USB, AND THE PROVISION OF OR FAILURE
 TO PROVIDE SUPPORT SERVICES. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL
 RIGHTS. YOU MAY HAVE OTHERS, WHICH VARY FROM STATE/JURISDICTION TO
 STATE/JURISDICTION.
@@ -127,11 +137,11 @@ IN NO EVENT SHALL OBJECTIVE DEVELOPMENT OR ITS SUPPLIERS BE LIABLE FOR ANY
 SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER
 (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,
 BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY
-LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE AVR-USB OR THE
+LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE V-USB OR THE
 PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES, EVEN IF OBJECTIVE
 DEVELOPMENT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN ANY
 CASE, OBJECTIVE DEVELOPMENT'S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS
-AGREEMENT SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR AVR-USB.
+AGREEMENT SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR V-USB.
 
 
 8 MISCELLANEOUS TERMS

avr/bootloader/usbdrv/License.txt

@@ -1,16 +1,18 @@
-OBJECTIVE DEVELOPMENT GmbH's AVR-USB driver software is distributed under the
+OBJECTIVE DEVELOPMENT GmbH's V-USB driver software is distributed under the
-terms and conditions of the GNU GPL version 2, see the text below. In addition
+terms and conditions of the GNU GPL version 2 or the GNU GPL version 3. It is
-to the requirements in the GPL, we STRONGLY ENCOURAGE you to do the following:
+your choice whether you apply the terms of version 2 or version 3. The full
+text of GPLv2 is included below. In addition to the requirements in the GPL,
+we STRONGLY ENCOURAGE you to do the following:
 
 (1) Publish your entire project on a web site and drop us a note with the URL.
-Use the form at http://www.obdev.at/avrusb/feedback.html for your submission.
+Use the form at http://www.obdev.at/vusb/feedback.html for your submission.
 
 (2) Adhere to minimum publication standards. Please include AT LEAST:
     - a circuit diagram in PDF, PNG or GIF format
     - full source code for the host software
     - a Readme.txt file in ASCII format which describes the purpose of the
       project and what can be found in which directories and which files
-    - a reference to http://www.obdev.at/avrusb/
+    - a reference to http://www.obdev.at/vusb/
 
 (3) If you improve the driver firmware itself, please give us a free license
 to your modifications for our commercial license offerings.

avr/bootloader/usbdrv/Readme.txt

@@ -1,6 +1,6 @@
 This is the Readme file to Objective Development's firmware-only USB driver
 for Atmel AVR microcontrollers. For more information please visit
-http://www.obdev.at/avrusb/
+http://www.obdev.at/vusb/
 
 This directory contains the USB firmware only. Copy it as-is to your own
 project and add all .c and .S files to your project (these files are marked
@@ -33,26 +33,26 @@ The driver consists of the following files:
                            defined to a value greater than 0. Link this module
                            to your code!
   oddebug.h .............. Interface definitions of the debug module.
-  iarcompat.h ............ Compatibility definitions for IAR C-compiler.
+  usbportability.h ....... Header with compiler-dependent stuff.
   usbdrvasm.asm .......... Compatibility stub for IAR-C-compiler. Use this
                            module instead of usbdrvasm.S when you assembler
                            with IAR's tools.
   License.txt ............ Open Source license for this driver.
   CommercialLicense.txt .. Optional commercial license for this driver.
-  USBID-License.txt ...... Terms and conditions for using particular USB ID
+  USB-ID-FAQ.txt ......... General infos about USB Product- and Vendor-IDs.
-                           values for particular purposes.
+  USB-IDs-for-free.txt ... List and terms of use for free shared PIDs.
 
 (*) ... These files should be linked to your project.
 
 
 CPU CORE CLOCK FREQUENCY
 ========================
-We supply assembler modules for clock frequencies of 12 MHz, 15 MHz, 16 MHz and
+We supply assembler modules for clock frequencies of 12 MHz, 12.8 MHz, 15 MHz,
-16.5 MHz. Other clock rates are not supported. The actual clock rate must be
+16 MHz, 16.5 MHz 18 MHz and 20 MHz. Other clock rates are not supported. The
-configured in usbdrv.h unless you use the default 12 MHz.
+actual clock rate must be configured in usbconfig.h.
 
 12 MHz Clock
-This is the traditional clock rate of AVR-USB because it's the lowest clock
+This is the traditional clock rate of V-USB because it's the lowest clock
 rate where the timing constraints of the USB spec can be met.
 
 15 MHz Clock
@@ -67,19 +67,29 @@ if you need the slightly higher clock rate for performance reasons. Since
 16 MHz is not divisible by the USB low speed bit clock of 1.5 MHz, the code
 is somewhat tricky and has to insert a leap cycle every third byte.
 
-16.5 MHz Clock
+12.8 MHz and 16.5 MHz Clock
-The assembler module for this clock rate differs from the other modules because
+The assembler modules for these clock rates differ from the other modules
-it has been built for an RC oscillator with only 1% precision. The receiver
+because they have been built for an RC oscillator with only 1% precision. The
-code inserts leap cycles to compensate for clock deviations. 1% is also the
+receiver code inserts leap cycles to compensate for clock deviations. 1% is
-precision which can be achieved by calibrating the internal RC oscillator of
+also the precision which can be achieved by calibrating the internal RC
-the AVR. Please note that only AVRs with internal 64 MHz PLL oscillator can be
+oscillator of the AVR. Please note that only AVRs with internal 64 MHz PLL
-used since the 8 MHz RC oscillator cannot be trimmed up to 16.5 MHz. This
+oscillator can reach 16.5 MHz with the RC oscillator. This includes the very
-includes the very popular ATTiny25, ATTiny45, ATTiny85 series as well as the
+popular ATTiny25, ATTiny45, ATTiny85 series as well as the ATTiny26. Almost
-ATTiny26.
+all AVRs can reach 12.8 MHz, although this is outside the specified range.
 
-See the EasyLogger example at http://www.obdev.at/avrusb/easylogger.html for
+See the EasyLogger example at http://www.obdev.at/vusb/easylogger.html for
 code which calibrates the RC oscillator based on the USB frame clock.
 
+18 MHz Clock
+This module is closer to the USB specification because it performs an on the
+fly CRC check for incoming packets. Packets with invalid checksum are
+discarded as required by the spec. If you also implement checks for data
+PID toggling on application level (see option USB_CFG_CHECK_DATA_TOGGLING
+in usbconfig.h for more info), this ensures data integrity. Due to the CRC
+tables and alignment requirements, this code is bigger than modules for other
+clock rates. To activate this module, you must define USB_CFG_CHECK_CRC to 1
+and USB_CFG_CLOCK_KHZ to 18000 in usbconfig.h.
+
 20 MHz Clock
 This module is for people who won't do it with less than the maximum. Since
 20 MHz is not divisible by the USB low speed bit clock of 1.5 MHz, the code
@@ -94,53 +104,69 @@ can assign PIDs at will.
 
 Since an entry level cost of 1,500 USD is too high for most small companies
 and hobbyists, we provide some VID/PID pairs for free. See the file
-USBID-License.txt for details.
+USB-IDs-for-free.txt for details.
 
 Objective Development also has some license offerings which include product
-IDs. See http://www.obdev.at/avrusb/ for details.
+IDs. See http://www.obdev.at/vusb/ for details.
 
 
 DEVELOPMENT SYSTEM
 ==================
 This driver has been developed and optimized for the GNU compiler version 3
-(gcc 3). It does work well with gcc 4, but with bigger code size. We recommend
+and 4. We recommend that you use the GNU compiler suite because it is freely
-that you use the GNU compiler suite because it is freely available. AVR-USB
+available. V-USB has also been ported to the IAR compiler and assembler. It
-has also been ported to the IAR compiler and assembler. It has been tested
+has been tested with IAR 4.10B/W32 and 4.12A/W32 on an ATmega8 with the
-with IAR 4.10B/W32 and 4.12A/W32 on an ATmega8 with the "small" and "tiny"
+"small" and "tiny" memory model. Not every release is tested with IAR CC and
-memory model. Not every release is tested with IAR CC and the driver may
+the driver may therefore fail to compile with IAR. Please note that gcc is
-therefore fail to compile with IAR. Please note that gcc is more efficient for
+more efficient for usbdrv.c because this module has been deliberately
-usbdrv.c because this module has been deliberately optimized for gcc.
+optimized for gcc.
+
+Gcc version 3 produces smaller code than version 4 due to new optimizing
+capabilities which don't always improve things on 8 bit CPUs. The code size
+generated by gcc 4 can be reduced with the compiler options
+-fno-move-loop-invariants, -fno-tree-scev-cprop and
+-fno-inline-small-functions in addition to -Os. On devices with more than
+8k of flash memory, we also recommend the linker option --relax (written as
+-Wl,--relax for gcc) to convert absolute calls into relative where possible.
+
+For more information about optimizing options see:
+
+    http://www.tty1.net/blog/2008-04-29-avr-gcc-optimisations_en.html
+
+These optimizations are good for gcc 4.x. Version 3.x of gcc does not support
+most of these options and produces good code anyway.
 
 
-USING AVR-USB FOR FREE
+USING V-USB FOR FREE
-======================
+====================
 The AVR firmware driver is published under the GNU General Public License
-Version 2 (GPL2). See the file "License.txt" for details.
+Version 2 (GPL2) and the GNU General Public License Version 3 (GPL3). It is
+your choice whether you apply the terms of version 2 or version 3.
 
-If you decide for the free GPL2, we STRONGLY ENCOURAGE you to do the following
+If you decide for the free GPL2 or GPL3, we STRONGLY ENCOURAGE you to do the
-things IN ADDITION to the obligations from the GPL2:
+following things IN ADDITION to the obligations from the GPL:
 
 (1) Publish your entire project on a web site and drop us a note with the URL.
-Use the form at http://www.obdev.at/avrusb/feedback.html for your submission.
+Use the form at http://www.obdev.at/vusb/feedback.html for your submission.
 If you don't have a web site, you can publish the project in obdev's
 documentation wiki at
-http://www.obdev.at/goto.php?t=avrusb-wiki&p=hosted-projects.
+http://www.obdev.at/goto.php?t=vusb-wiki&p=hosted-projects.
 
 (2) Adhere to minimum publication standards. Please include AT LEAST:
     - a circuit diagram in PDF, PNG or GIF format
     - full source code for the host software
     - a Readme.txt file in ASCII format which describes the purpose of the
       project and what can be found in which directories and which files
-    - a reference to http://www.obdev.at/avrusb/
+    - a reference to http://www.obdev.at/vusb/
 
 (3) If you improve the driver firmware itself, please give us a free license
 to your modifications for our commercial license offerings.
 
 
-COMMERCIAL LICENSES FOR AVR-USB
+COMMERCIAL LICENSES FOR V-USB
-===============================
+=============================
-If you don't want to publish your source code under the terms of the GPL2,
+If you don't want to publish your source code under the terms of the GPL,
-you can simply pay money for AVR-USB. As an additional benefit you get
+you can simply pay money for V-USB. As an additional benefit you get
-USB PIDs for free, licensed exclusively to you. See the file
+USB PIDs for free, reserved exclusively to you. See the file
 "CommercialLicense.txt" for details.
 

avr/bootloader/usbdrv/asmcommon.inc

@@ -1,11 +1,10 @@
 /* Name: asmcommon.inc
- * Project: AVR USB driver
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
  * Author: Christian Starkjohann
  * Creation Date: 2007-11-05
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id$
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the
@@ -103,8 +102,11 @@ sofError:
     reti
 
 handleData:
-    lds     token, usbCurrentTok;[18]
+#if USB_CFG_CHECK_CRC
-    tst     token               ;[20]
+    CRC_CLEANUP_AND_CHECK       ; jumps to ignorePacket if CRC error
+#endif
+    lds     shift, usbCurrentTok;[18]
+    tst     shift               ;[20]
     breq    doReturn            ;[21]
     lds     x2, usbRxLen        ;[22]
     tst     x2                  ;[24]
@@ -113,8 +115,11 @@ handleData:
 ; recognized if usbPoll() was called less frequently than once every 4 ms.
     cpi     cnt, 4              ;[26] zero sized data packets are status phase only -- ignore and ack
     brmi    sendAckAndReti      ;[27] keep rx buffer clean -- we must not NAK next SETUP
+#if USB_CFG_CHECK_DATA_TOGGLING
+    sts     usbCurrentDataToken, token  ; store for checking by C code
+#endif
     sts     usbRxLen, cnt       ;[28] store received data, swap buffers
-    sts     usbRxToken, token   ;[30]
+    sts     usbRxToken, shift   ;[30]
     lds     x2, usbInputBufOffset;[32] swap buffers
     ldi     cnt, USB_BUFSIZE    ;[34]
     sub     cnt, x2             ;[35]
@@ -131,7 +136,11 @@ handleIn:
     ldi     x1, USBPID_NAK      ;[34] prepare value for usbTxLen
 #if USB_CFG_HAVE_INTRIN_ENDPOINT
     andi    x3, 0xf             ;[35] x3 contains endpoint
+#if USB_CFG_SUPPRESS_INTR_CODE
+    brne    sendNakAndReti      ;[36]
+#else
     brne    handleIn1           ;[36]
+#endif
 #endif
     lds     cnt, usbTxLen       ;[37]
     sbrc    cnt, 4              ;[39] all handshake tokens have bit 4 set
@@ -150,7 +159,7 @@ handleIn:
 ; RAM this way and avoid potential problems with endless retries. The rest of
 ; the driver assumes error-free transfers anyway.
 
-#if USB_CFG_HAVE_INTRIN_ENDPOINT    /* placed here due to relative jump range */
+#if !USB_CFG_SUPPRESS_INTR_CODE && USB_CFG_HAVE_INTRIN_ENDPOINT /* placed here due to relative jump range */
 handleIn1:                      ;[38]
 #if USB_CFG_HAVE_INTRIN_ENDPOINT3
 ; 2006-06-10 as suggested by O.Tamura: support second INTR IN / BULK IN endpoint
@@ -164,9 +173,8 @@ handleIn1:                      ;[38]
     ldi     YL, lo8(usbTxBuf1)  ;[46]
     ldi     YH, hi8(usbTxBuf1)  ;[47]
     rjmp    usbSendAndReti      ;[48] 50 + 12 = 62 until SOP
-#endif
 
-#if USB_CFG_HAVE_INTRIN_ENDPOINT && USB_CFG_HAVE_INTRIN_ENDPOINT3
+#if USB_CFG_HAVE_INTRIN_ENDPOINT3
 handleIn3:
     lds     cnt, usbTxLen3      ;[41]
     sbrc    cnt, 4              ;[43]
@@ -176,3 +184,4 @@ handleIn3:
     ldi     YH, hi8(usbTxBuf3)  ;[48]
     rjmp    usbSendAndReti      ;[49] 51 + 12 = 63 until SOP
 #endif
+#endif

avr/bootloader/usbdrv/oddebug.c

@@ -4,8 +4,7 @@
  * Creation Date: 2005-01-16
  * Tabsize: 4
  * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: oddebug.c 275 2007-03-20 09:58:28Z cs $
  */
 
 #include "oddebug.h"

avr/bootloader/usbdrv/oddebug.h

@@ -4,8 +4,7 @@
  * Creation Date: 2005-01-16
  * Tabsize: 4
  * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: oddebug.h 275 2007-03-20 09:58:28Z cs $
  */
 
 #ifndef __oddebug_h_included__
@@ -29,10 +28,7 @@ the output and a memory block to dump in hex ('data' and 'len').
 #endif
 
 /* make sure we have the UART defines: */
-#include "iarcompat.h"
+#include "usbportability.h"
-#ifndef __IAR_SYSTEMS_ICC__
-#   include <avr/io.h>
-#endif
 
 #ifndef uchar
 #   define  uchar   unsigned char

avr/bootloader/usbdrv/usbconfig-prototype.h

@@ -1,11 +1,10 @@
 /* Name: usbconfig.h
- * Project: AVR USB driver
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
  * Author: Christian Starkjohann
  * Creation Date: 2005-04-01
  * Tabsize: 4
  * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbconfig-prototype.h 600 2008-05-13 10:34:56Z cs $
  */
 
 #ifndef __usbconfig_h_included__
@@ -14,7 +13,7 @@
 /*
 General Description:
 This file is an example configuration (with inline documentation) for the USB
-driver. It configures AVR-USB for USB D+ connected to Port D bit 2 (which is
+driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
 also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
 wire the lines to any other port, as long as D+ is also wired to INT0 (or any
 other hardware interrupt, as long as it is the highest level interrupt, see
@@ -44,11 +43,19 @@ section at the end of this file).
  * markers every millisecond.]
  */
 #define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
-/* Clock rate of the AVR in MHz. Legal values are 12000, 15000, 16000, 16500
+/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
- * and 20000. The 16.5 MHz version of the code requires no crystal, it
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
- * tolerates +/- 1% deviation from the nominal frequency. All other rates
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
- * require a precision of 2000 ppm and thus a crystal!
+ * frequency. All other rates require a precision of 2000 ppm and thus a
- * Default if not specified: 12 MHz
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
+ */
+#define USB_CFG_CHECK_CRC       0
+/* Define this to 1 if you want that the driver checks integrity of incoming
+ * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * currently only available for 18 MHz crystal clock. You must choose
+ * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
  */
 
 /* ----------------------- Optional Hardware Config ------------------------ */
@@ -94,6 +101,14 @@ section at the end of this file).
  * it is required by the standard. We have made it a config option because it
  * bloats the code considerably.
  */
+#define USB_CFG_SUPPRESS_INTR_CODE      0
+/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
+ * want to send any data over them. If this macro is defined to 1, functions
+ * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
+ * you need the interrupt-in endpoints in order to comply to an interface
+ * (e.g. HID), but never want to send any data. This option saves a couple
+ * of bytes in flash memory and the transmit buffers in RAM.
+ */
 #define USB_CFG_INTR_POLL_INTERVAL      10
 /* If you compile a version with endpoint 1 (interrupt-in), this is the poll
  * interval. The value is in milliseconds and must not be less than 10 ms for
@@ -130,6 +145,11 @@ section at the end of this file).
  * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
  * usbdrv.h.
  */
+#define USB_CFG_DRIVER_FLASH_PAGE       0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
 #define USB_CFG_LONG_TRANSFERS          0
 /* Define this to 1 if you want to send/receive blocks of more than 254 bytes
  * in a single control-in or control-out transfer. Note that the capability
@@ -156,28 +176,67 @@ section at the end of this file).
  * counts SOF packets. This feature requires that the hardware interrupt is
  * connected to D- instead of D+.
  */
+/* #ifdef __ASSEMBLER__
+ * macro myAssemblerMacro
+ *     in      YL, TCNT0
+ *     sts     timer0Snapshot, YL
+ *     endm
+ * #endif
+ * #define USB_SOF_HOOK                    myAssemblerMacro
+ * This macro (if defined) is executed in the assembler module when a
+ * Start Of Frame condition is detected. It is recommended to define it to
+ * the name of an assembler macro which is defined here as well so that more
+ * than one assembler instruction can be used. The macro may use the register
+ * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
+ * immediately after an SOF pulse may be lost and must be retried by the host.
+ * What can you do with this hook? Since the SOF signal occurs exactly every
+ * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
+ * designs running on the internal RC oscillator.
+ * Please note that Start Of Frame detection works only if D- is wired to the
+ * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
+ */
+#define USB_CFG_CHECK_DATA_TOGGLING     0
+/* define this macro to 1 if you want to filter out duplicate data packets
+ * sent by the host. Duplicates occur only as a consequence of communication
+ * errors, when the host does not receive an ACK. Please note that you need to
+ * implement the filtering yourself in usbFunctionWriteOut() and
+ * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
+ * for each control- and out-endpoint to check for duplicate packets.
+ */
 #define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   0
 /* define this macro to 1 if you want the function usbMeasureFrameLength()
  * compiled in. This function can be used to calibrate the AVR's RC oscillator.
  */
+#define USB_USE_FAST_CRC                0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
 
 /* -------------------------- Device Description --------------------------- */
 
-#define  USB_CFG_VENDOR_ID       0xc0, 0x16
+#define  USB_CFG_VENDOR_ID       0xc0, 0x16 /* = 0x16c0 = 5824 = voti.nl */
 /* USB vendor ID for the device, low byte first. If you have registered your
- * own Vendor ID, define it here. Otherwise you use one of obdev's free shared
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
- * VID/PID pairs. Be sure to read USBID-License.txt for rules!
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
- * + This template uses obdev's shared VID/PID pair: 0x16c0/0x5dc.
+ * *** IMPORTANT NOTE ***
- * + Use this VID/PID pair ONLY if you understand the implications!
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
  */
-#define  USB_CFG_DEVICE_ID       0xdc, 0x05
+#define  USB_CFG_DEVICE_ID       0xdc, 0x05 /* = 0x05dc = 1500 */
 /* This is the ID of the product, low byte first. It is interpreted in the
  * scope of the vendor ID. If you have registered your own VID with usb.org
  * or if you have licensed a PID from somebody else, define it here. Otherwise
- * you use obdev's free shared VID/PID pair. Be sure to read the rules in
+ * you may use one of obdev's free shared VID/PID pairs. See the file
- * USBID-License.txt!
+ * USB-IDs-for-free.txt for details!
- * + This template uses obdev's shared VID/PID pair: 0x16c0/0x5dc.
+ * *** IMPORTANT NOTE ***
- * + Use this VID/PID pair ONLY if you understand the implications!
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
  */
 #define USB_CFG_DEVICE_VERSION  0x00, 0x01
 /* Version number of the device: Minor number first, then major number.
@@ -189,14 +248,14 @@ section at the end of this file).
  * are interpreted as Unicode (UTF-16) entities.
  * If you don't want a vendor name string, undefine these macros.
  * ALWAYS define a vendor name containing your Internet domain name if you use
- * obdev's free shared VID/PID pair. See the file USBID-License.txt for
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
  * details.
  */
 #define USB_CFG_DEVICE_NAME     'T', 'e', 'm', 'p', 'l', 'a', 't', 'e'
 #define USB_CFG_DEVICE_NAME_LEN 8
 /* Same as above for the device name. If you don't want a device name, undefine
- * the macros. See the file USBID-License.txt before you assign a name if you
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
- * use a shared VID/PID.
+ * you use a shared VID/PID.
  */
 /*#define USB_CFG_SERIAL_NUMBER   'N', 'o', 'n', 'e' */
 /*#define USB_CFG_SERIAL_NUMBER_LEN   0 */
@@ -243,7 +302,9 @@ section at the end of this file).
  * no properties are defined or if they are 0, the default descriptor is used.
  * Possible properties are:
  *   + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
- *     at runtime via usbFunctionDescriptor().
+ *     at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
+ *     used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
+ *     you want RAM pointers.
  *   + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
  *     in static memory is in RAM, not in flash memory.
  *   + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
@@ -275,6 +336,12 @@ section at the end of this file).
  *   USB_CFG_DESCR_PROPS_HID_REPORT
  *   USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
  *
+ * Note about string descriptors: String descriptors are not just strings, they
+ * are Unicode strings prefixed with a 2 byte header. Example:
+ * int  serialNumberDescriptor[] = {
+ *     USB_STRING_DESCRIPTOR_HEADER(6),
+ *     'S', 'e', 'r', 'i', 'a', 'l'
+ * };
  */
 
 #define USB_CFG_DESCR_PROPS_DEVICE                  0
@@ -288,6 +355,15 @@ section at the end of this file).
 #define USB_CFG_DESCR_PROPS_HID_REPORT              0
 #define USB_CFG_DESCR_PROPS_UNKNOWN                 0
 
+
+#define usbMsgPtr_t unsigned short
+/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
+ * a scalar type here because gcc generates slightly shorter code for scalar
+ * arithmetics than for pointer arithmetics. Remove this define for backward
+ * type compatibility or define it to an 8 bit type if you use data in RAM only
+ * and all RAM is below 256 bytes (tiny memory model in IAR CC).
+ */
+
 /* ----------------------- Optional MCU Description ------------------------ */
 
 /* The following configurations have working defaults in usbdrv.h. You
@@ -303,6 +379,6 @@ section at the end of this file).
 /* #define USB_INTR_ENABLE_BIT     INT0 */
 /* #define USB_INTR_PENDING        GIFR */
 /* #define USB_INTR_PENDING_BIT    INTF0 */
-/* #define USB_INTR_VECTOR         SIG_INTERRUPT0 */
+/* #define USB_INTR_VECTOR         INT0_vect */
 
 #endif /* __usbconfig_h_included__ */

avr/bootloader/usbdrv/usbdrv.c

@@ -1,18 +1,12 @@
 /* Name: usbdrv.c
- * Project: AVR USB driver
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
  * Author: Christian Starkjohann
  * Creation Date: 2004-12-29
  * Tabsize: 4
  * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbdrv.c 591 2008-05-03 20:21:19Z cs $
  */
 
-#include "iarcompat.h"
-#ifndef __IAR_SYSTEMS_ICC__
-#   include <avr/io.h>
-#   include <avr/pgmspace.h>
-#endif
 #include "usbdrv.h"
 #include "oddebug.h"
 
@@ -38,15 +32,18 @@ uchar       usbTxBuf[USB_BUFSIZE];/* data to transmit with next IN, free if usbT
 #if USB_COUNT_SOF
 volatile uchar  usbSofCount;    /* incremented by assembler module every SOF */
 #endif
-#if USB_CFG_HAVE_INTRIN_ENDPOINT
+#if USB_CFG_HAVE_INTRIN_ENDPOINT && !USB_CFG_SUPPRESS_INTR_CODE
 usbTxStatus_t  usbTxStatus1;
 #   if USB_CFG_HAVE_INTRIN_ENDPOINT3
 usbTxStatus_t  usbTxStatus3;
 #   endif
 #endif
+#if USB_CFG_CHECK_DATA_TOGGLING
+uchar       usbCurrentDataToken;/* when we check data toggling to ignore duplicate packets */
+#endif
 
 /* USB status registers / not shared with asm code */
-uchar               *usbMsgPtr;     /* data to transmit next -- ROM or RAM address */
+usbMsgPtr_t         usbMsgPtr;      /* data to transmit next -- ROM or RAM address */
 static usbMsgLen_t  usbMsgLen = USB_NO_MSG; /* remaining number of bytes */
 static uchar        usbMsgFlags;    /* flag values see below */
 
@@ -56,7 +53,7 @@ static uchar        usbMsgFlags;    /* flag values see below */
 /*
 optimizing hints:
 - do not post/pre inc/dec integer values in operations
-- assign value of PRG_RDB() to register variables and don't use side effects in arg
+- assign value of USB_READ_FLASH() to register variables and don't use side effects in arg
 - use narrow scope for variables which should be in X/Y/Z register
 - assign char sized expressions to variables to force 8 bit arithmetics
 */
@@ -68,7 +65,7 @@ optimizing hints:
 #if USB_CFG_DESCR_PROPS_STRING_0 == 0
 #undef USB_CFG_DESCR_PROPS_STRING_0
 #define USB_CFG_DESCR_PROPS_STRING_0    sizeof(usbDescriptorString0)
-PROGMEM char usbDescriptorString0[] = { /* language descriptor */
+PROGMEM const char usbDescriptorString0[] = { /* language descriptor */
     4,          /* sizeof(usbDescriptorString0): length of descriptor in bytes */
     3,          /* descriptor type */
     0x09, 0x04, /* language index (0x0409 = US-English) */
@@ -78,7 +75,7 @@ PROGMEM char usbDescriptorString0[] = { /* language descriptor */
 #if USB_CFG_DESCR_PROPS_STRING_VENDOR == 0 && USB_CFG_VENDOR_NAME_LEN
 #undef USB_CFG_DESCR_PROPS_STRING_VENDOR
 #define USB_CFG_DESCR_PROPS_STRING_VENDOR   sizeof(usbDescriptorStringVendor)
-PROGMEM int  usbDescriptorStringVendor[] = {
+PROGMEM const int  usbDescriptorStringVendor[] = {
     USB_STRING_DESCRIPTOR_HEADER(USB_CFG_VENDOR_NAME_LEN),
     USB_CFG_VENDOR_NAME
 };
@@ -87,7 +84,7 @@ PROGMEM int  usbDescriptorStringVendor[] = {
 #if USB_CFG_DESCR_PROPS_STRING_PRODUCT == 0 && USB_CFG_DEVICE_NAME_LEN
 #undef USB_CFG_DESCR_PROPS_STRING_PRODUCT
 #define USB_CFG_DESCR_PROPS_STRING_PRODUCT   sizeof(usbDescriptorStringDevice)
-PROGMEM int  usbDescriptorStringDevice[] = {
+PROGMEM const int  usbDescriptorStringDevice[] = {
     USB_STRING_DESCRIPTOR_HEADER(USB_CFG_DEVICE_NAME_LEN),
     USB_CFG_DEVICE_NAME
 };
@@ -96,7 +93,7 @@ PROGMEM int  usbDescriptorStringDevice[] = {
 #if USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER == 0 && USB_CFG_SERIAL_NUMBER_LEN
 #undef USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
 #define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    sizeof(usbDescriptorStringSerialNumber)
-PROGMEM int usbDescriptorStringSerialNumber[] = {
+PROGMEM const int usbDescriptorStringSerialNumber[] = {
     USB_STRING_DESCRIPTOR_HEADER(USB_CFG_SERIAL_NUMBER_LEN),
     USB_CFG_SERIAL_NUMBER
 };
@@ -109,7 +106,7 @@ PROGMEM int usbDescriptorStringSerialNumber[] = {
 #if USB_CFG_DESCR_PROPS_DEVICE == 0
 #undef USB_CFG_DESCR_PROPS_DEVICE
 #define USB_CFG_DESCR_PROPS_DEVICE  sizeof(usbDescriptorDevice)
-PROGMEM char usbDescriptorDevice[] = {    /* USB device descriptor */
+PROGMEM const char usbDescriptorDevice[] = {    /* USB device descriptor */
     18,         /* sizeof(usbDescriptorDevice): length of descriptor in bytes */
     USBDESCR_DEVICE,        /* descriptor type */
     0x10, 0x01,             /* USB version supported */
@@ -140,7 +137,7 @@ PROGMEM char usbDescriptorDevice[] = {    /* USB device descriptor */
 #if USB_CFG_DESCR_PROPS_CONFIGURATION == 0
 #undef USB_CFG_DESCR_PROPS_CONFIGURATION
 #define USB_CFG_DESCR_PROPS_CONFIGURATION   sizeof(usbDescriptorConfiguration)
-PROGMEM char usbDescriptorConfiguration[] = {    /* USB configuration descriptor */
+PROGMEM const char usbDescriptorConfiguration[] = {    /* USB configuration descriptor */
     9,          /* sizeof(usbDescriptorConfiguration): length of descriptor in bytes */
     USBDESCR_CONFIG,    /* descriptor type */
     18 + 7 * USB_CFG_HAVE_INTRIN_ENDPOINT + 7 * USB_CFG_HAVE_INTRIN_ENDPOINT3 +
@@ -150,9 +147,9 @@ PROGMEM char usbDescriptorConfiguration[] = {    /* USB configuration descriptor
     1,          /* index of this configuration */
     0,          /* configuration name string index */
 #if USB_CFG_IS_SELF_POWERED
-    USBATTR_SELFPOWER,      /* attributes */
+    (1 << 7) | USBATTR_SELFPOWER,       /* attributes */
 #else
-    (char)USBATTR_BUSPOWER, /* attributes */
+    (1 << 7),                           /* attributes */
 #endif
     USB_CFG_MAX_BUS_POWER/2,            /* max USB current in 2mA units */
 /* interface descriptor follows inline: */
@@ -185,7 +182,7 @@ PROGMEM char usbDescriptorConfiguration[] = {    /* USB configuration descriptor
 #if USB_CFG_HAVE_INTRIN_ENDPOINT3   /* endpoint descriptor for endpoint 3 */
     7,          /* sizeof(usbDescrEndpoint) */
     USBDESCR_ENDPOINT,  /* descriptor type = endpoint */
-    (char)0x83, /* IN endpoint number 1 */
+    (char)(0x80 | USB_CFG_EP3_NUMBER), /* IN endpoint number 3 */
     0x03,       /* attrib: Interrupt endpoint */
     8, 0,       /* maximum packet size */
     USB_CFG_INTR_POLL_INTERVAL, /* in ms */
@@ -195,18 +192,9 @@ PROGMEM char usbDescriptorConfiguration[] = {    /* USB configuration descriptor
 
 /* ------------------------------------------------------------------------- */
 
-/* We don't use prog_int or prog_int16_t for compatibility with various libc
- * versions. Here's an other compatibility hack:
- */
-#ifndef PRG_RDB
-#define PRG_RDB(addr)   pgm_read_byte(addr)
-#endif
-
-/* ------------------------------------------------------------------------- */
-
 static inline void  usbResetDataToggling(void)
 {
-#if USB_CFG_HAVE_INTRIN_ENDPOINT
+#if USB_CFG_HAVE_INTRIN_ENDPOINT && !USB_CFG_SUPPRESS_INTR_CODE
     USB_SET_DATATOKEN1(USB_INITIAL_DATATOKEN);  /* reset data toggling for interrupt endpoint */
 #   if USB_CFG_HAVE_INTRIN_ENDPOINT3
     USB_SET_DATATOKEN3(USB_INITIAL_DATATOKEN);  /* reset data toggling for interrupt endpoint */
@@ -226,6 +214,7 @@ static inline void  usbResetStall(void)
 
 /* ------------------------------------------------------------------------- */
 
+#if !USB_CFG_SUPPRESS_INTR_CODE
 #if USB_CFG_HAVE_INTRIN_ENDPOINT
 static void usbGenericSetInterrupt(uchar *data, uchar len, usbTxStatus_t *txStatus)
 {
@@ -263,6 +252,7 @@ USB_PUBLIC void usbSetInterrupt3(uchar *data, uchar len)
     usbGenericSetInterrupt(data, len, &usbTxStatus3);
 }
 #endif
+#endif /* USB_CFG_SUPPRESS_INTR_CODE */
 
 /* ------------------ utilities for code following below ------------------- */
 
@@ -309,7 +299,7 @@ USB_PUBLIC void usbSetInterrupt3(uchar *data, uchar len)
             len = usbFunctionDescriptor(rq);        \
         }else{                                      \
             len = USB_PROP_LENGTH(cfgProp);         \
-            usbMsgPtr = (uchar *)(staticName);      \
+            usbMsgPtr = (usbMsgPtr_t)(staticName);  \
         }                                           \
     }
 
@@ -369,7 +359,8 @@ uchar       flags = USB_FLG_MSGPTR_IS_ROM;
  */
 static inline usbMsgLen_t usbDriverSetup(usbRequest_t *rq)
 {
-uchar   len  = 0, *dataPtr = usbTxBuf + 9;  /* there are 2 bytes free space at the end of the buffer */
+usbMsgLen_t len = 0;
+uchar   *dataPtr = usbTxBuf + 9;    /* there are 2 bytes free space at the end of the buffer */
 uchar   value = rq->wValue.bytes[0];
 #if USB_CFG_IMPLEMENT_HALT
 uchar   index = rq->wIndex.bytes[0];
@@ -408,7 +399,7 @@ uchar   index = rq->wIndex.bytes[0];
         usbResetStall();
     SWITCH_CASE(USBRQ_GET_INTERFACE)        /* 10 */
         len = 1;
-#if USB_CFG_HAVE_INTRIN_ENDPOINT
+#if USB_CFG_HAVE_INTRIN_ENDPOINT && !USB_CFG_SUPPRESS_INTR_CODE
     SWITCH_CASE(USBRQ_SET_INTERFACE)        /* 11 */
         usbResetDataToggling();
         usbResetStall();
@@ -416,7 +407,7 @@ uchar   index = rq->wIndex.bytes[0];
     SWITCH_DEFAULT                          /* 7=SET_DESCRIPTOR, 12=SYNC_FRAME */
         /* Should we add an optional hook here? */
     SWITCH_END
-    usbMsgPtr = dataPtr;
+    usbMsgPtr = (usbMsgPtr_t)dataPtr;
 skipMsgPtrAssignment:
     return len;
 }
@@ -436,7 +427,7 @@ usbRequest_t    *rq = (void *)data;
  * 0xe1 11100001 (USBPID_OUT: data phase of setup transfer)
  * 0...0x0f for OUT on endpoint X
  */
-    DBG2(0x10 + (usbRxToken & 0xf), data, len); /* SETUP=1d, SETUP-DATA=11, OUTx=1x */
+    DBG2(0x10 + (usbRxToken & 0xf), data, len + 2); /* SETUP=1d, SETUP-DATA=11, OUTx=1x */
     USB_RX_USER_HOOK(data, len)
 #if USB_CFG_IMPLEMENT_FN_WRITEOUT
     if(usbRxToken < 0x10){  /* OUT to endpoint != 0: endpoint number in usbRxToken */
@@ -459,9 +450,13 @@ usbRequest_t    *rq = (void *)data;
         }
 #if USB_CFG_IMPLEMENT_FN_READ || USB_CFG_IMPLEMENT_FN_WRITE
         if(replyLen == USB_NO_MSG){         /* use user-supplied read/write function */
-            /* do some conditioning on replyLen */
+            /* do some conditioning on replyLen, but on IN transfers only */
             if((rq->bmRequestType & USBRQ_DIR_MASK) != USBRQ_DIR_HOST_TO_DEVICE){
-                replyLen = rq->wLength.bytes[0];    /* IN transfers only */
+                if(sizeof(replyLen) < sizeof(rq->wLength.word)){ /* help compiler with optimizing */
+                    replyLen = rq->wLength.bytes[0];
+                }else{
+                    replyLen = rq->wLength.word;
+                }
             }
             usbMsgFlags = USB_FLG_USE_USER_RW;
         }else   /* The 'else' prevents that we limit a replyLen of USB_NO_MSG to the maximum transfer len. */
@@ -502,16 +497,18 @@ static uchar usbDeviceRead(uchar *data, uchar len)
         }else
 #endif
         {
-            uchar i = len, *r = usbMsgPtr;
+            uchar i = len;
+            usbMsgPtr_t r = usbMsgPtr;
             if(usbMsgFlags & USB_FLG_MSGPTR_IS_ROM){    /* ROM data */
                 do{
-                    uchar c = PRG_RDB(r);    /* assign to char size variable to enforce byte ops */
+                    uchar c = USB_READ_FLASH(r);    /* assign to char size variable to enforce byte ops */
                     *data++ = c;
                     r++;
                 }while(--i);
             }else{  /* RAM data */
                 do{
-                    *data++ = *r++;
+                    *data++ = *((uchar *)r);
+                    r++;
                 }while(--i);
             }
             usbMsgPtr = r;
@@ -561,6 +558,8 @@ uchar           isReset = !notResetState;
         USB_RESET_HOOK(isReset);
         wasReset = isReset;
     }
+#else
+    notResetState = notResetState;  // avoid compiler warning
 #endif
 }
 
@@ -592,17 +591,17 @@ uchar   i;
             usbBuildTxBlock();
         }
     }
-    for(i = 10; i > 0; i--){
+    for(i = 20; i > 0; i--){
         uchar usbLineStatus = USBIN & USBMASK;
         if(usbLineStatus != 0)  /* SE0 has ended */
-            break;
+            goto isNotReset;
-    }
-    if(i == 0){ /* RESET condition, called multiple times during reset */
-        usbNewDeviceAddr = 0;
-        usbDeviceAddr = 0;
-        usbResetStall();
-        DBG1(0xff, 0, 0);
     }
+    /* RESET condition, called multiple times during reset */
+    usbNewDeviceAddr = 0;
+    usbDeviceAddr = 0;
+    usbResetStall();
+    DBG1(0xff, 0, 0);
+isNotReset:
     usbHandleResetHook(i);
 }
 
@@ -618,7 +617,7 @@ USB_PUBLIC void usbInit(void)
 #endif
     USB_INTR_ENABLE |= (1 << USB_INTR_ENABLE_BIT);
     usbResetDataToggling();
-#if USB_CFG_HAVE_INTRIN_ENDPOINT
+#if USB_CFG_HAVE_INTRIN_ENDPOINT && !USB_CFG_SUPPRESS_INTR_CODE
     usbTxLen1 = USBPID_NAK;
 #if USB_CFG_HAVE_INTRIN_ENDPOINT3
     usbTxLen3 = USBPID_NAK;

avr/bootloader/usbdrv/usbdrv.h

@@ -1,17 +1,16 @@
 /* Name: usbdrv.h
- * Project: AVR USB driver
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
  * Author: Christian Starkjohann
  * Creation Date: 2004-12-29
  * Tabsize: 4
  * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbdrv.h 607 2008-05-13 15:57:28Z cs $
  */
 
 #ifndef __usbdrv_h_included__
 #define __usbdrv_h_included__
 #include "usbconfig.h"
-#include "iarcompat.h"
+#include "usbportability.h"
 
 /*
 Hardware Prerequisites:
@@ -34,8 +33,8 @@ usbDeviceConnect() and usbDeviceDisconnect() further down in this file.
 
 Please adapt the values in usbconfig.h according to your hardware!
 
-The device MUST be clocked at exactly 12 MHz, 15 MHz or 16 MHz
+The device MUST be clocked at exactly 12 MHz, 15 MHz, 16 MHz or 20 MHz
-or at 16.5 MHz +/- 1%. See usbconfig-prototype.h for details.
+or at 12.8 MHz resp. 16.5 MHz +/- 1%. See usbconfig-prototype.h for details.
 
 
 Limitations:
@@ -105,9 +104,9 @@ interrupt routine.
 Interrupt latency:
 The application must ensure that the USB interrupt is not disabled for more
 than 25 cycles (this is for 12 MHz, faster clocks allow longer latency).
-This implies that all interrupt routines must either be declared as "INTERRUPT"
+This implies that all interrupt routines must either have the "ISR_NOBLOCK"
-instead of "SIGNAL" (see "avr/signal.h") or that they are written in assembler
+attribute set (see "avr/interrupt.h") or be written in assembler with "sei"
-with "sei" as the first instruction.
+as the first instruction.
 
 Maximum interrupt duration / CPU cycle consumption:
 The driver handles all USB communication during the interrupt service
@@ -122,7 +121,7 @@ USB messages, even if they address another (low-speed) device on the same bus.
 /* --------------------------- Module Interface ---------------------------- */
 /* ------------------------------------------------------------------------- */
 
-#define USBDRV_VERSION  20080513
+#define USBDRV_VERSION  20121206
 /* This define uniquely identifies a driver version. It is a decimal number
  * constructed from the driver's release date in the form YYYYMMDD. If the
  * driver's behavior or interface changes, you can use this constant to
@@ -163,11 +162,24 @@ USB messages, even if they address another (low-speed) device on the same bus.
  */
 #define USB_NO_MSG  ((usbMsgLen_t)-1)   /* constant meaning "no message" */
 
+#ifndef usbMsgPtr_t
+#define usbMsgPtr_t uchar *
+#endif
+/* Making usbMsgPtr_t a define allows the user of this library to define it to
+ * an 8 bit type on tiny devices. This reduces code size, especially if the
+ * compiler supports a tiny memory model.
+ * The type can be a pointer or scalar type, casts are made where necessary.
+ * Although it's paradoxical, Gcc 4 generates slightly better code for scalar
+ * types than for pointers.
+ */
+
 struct usbRequest;  /* forward declaration */
 
 USB_PUBLIC void usbInit(void);
 /* This function must be called before interrupts are enabled and the main
- * loop is entered.
+ * loop is entered. We exepct that the PORT and DDR bits for D+ and D- have
+ * not been changed from their default status (which is 0). If you have changed
+ * them, set both back to 0 (configure them as input with no internal pull-up).
  */
 USB_PUBLIC void usbPoll(void);
 /* This function must be called at regular intervals from the main loop.
@@ -176,7 +188,7 @@ USB_PUBLIC void usbPoll(void);
  * Please note that debug outputs through the UART take ~ 0.5ms per byte
  * at 19200 bps.
  */
-extern uchar *usbMsgPtr;
+extern usbMsgPtr_t usbMsgPtr;
 /* This variable may be used to pass transmit data to the driver from the
  * implementation of usbFunctionWrite(). It is also used internally by the
  * driver for standard control requests.
@@ -273,6 +285,8 @@ USB_PUBLIC uchar usbFunctionRead(uchar *data, uchar len);
  * to 1 in usbconfig.h and return 0xff in usbFunctionSetup()..
  */
 #endif /* USB_CFG_IMPLEMENT_FN_READ */
+
+extern uchar usbRxToken;    /* may be used in usbFunctionWriteOut() below */
 #if USB_CFG_IMPLEMENT_FN_WRITEOUT
 USB_PUBLIC void usbFunctionWriteOut(uchar *data, uchar len);
 /* This function is called by the driver when data is received on an interrupt-
@@ -339,6 +353,12 @@ extern volatile uchar   usbSofCount;
  * the macro USB_COUNT_SOF is defined to a value != 0.
  */
 #endif
+#if USB_CFG_CHECK_DATA_TOGGLING
+extern uchar    usbCurrentDataToken;
+/* This variable can be checked in usbFunctionWrite() and usbFunctionWriteOut()
+ * to ignore duplicate packets.
+ */
+#endif
 
 #define USB_STRING_DESCRIPTOR_HEADER(stringLength) ((2*(stringLength)+2) | (3<<8))
 /* This macro builds a descriptor header for a string descriptor given the
@@ -380,11 +400,13 @@ extern volatile schar   usbRxLen;
  * about the various methods to define USB descriptors. If you do nothing,
  * the default descriptors will be used.
  */
-#define USB_PROP_IS_DYNAMIC     (1 << 14)
+#define USB_PROP_IS_DYNAMIC     (1u << 14)
 /* If this property is set for a descriptor, usbFunctionDescriptor() will be
- * used to obtain the particular descriptor.
+ * used to obtain the particular descriptor. Data directly returned via
+ * usbMsgPtr are FLASH data by default, combine (OR) with USB_PROP_IS_RAM to
+ * return RAM data.
  */
-#define USB_PROP_IS_RAM         (1 << 15)
+#define USB_PROP_IS_RAM         (1u << 15)
 /* If this property is set for a descriptor, the data is read from RAM
  * memory instead of Flash. The property is used for all methods to provide
  * external descriptors.
@@ -438,43 +460,43 @@ extern volatile schar   usbRxLen;
 #ifndef __ASSEMBLER__
 extern
 #if !(USB_CFG_DESCR_PROPS_DEVICE & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 char usbDescriptorDevice[];
 
 extern
 #if !(USB_CFG_DESCR_PROPS_CONFIGURATION & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 char usbDescriptorConfiguration[];
 
 extern
 #if !(USB_CFG_DESCR_PROPS_HID_REPORT & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 char usbDescriptorHidReport[];
 
 extern
 #if !(USB_CFG_DESCR_PROPS_STRING_0 & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 char usbDescriptorString0[];
 
 extern
 #if !(USB_CFG_DESCR_PROPS_STRING_VENDOR & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 int usbDescriptorStringVendor[];
 
 extern
 #if !(USB_CFG_DESCR_PROPS_STRING_PRODUCT & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 int usbDescriptorStringDevice[];
 
 extern
 #if !(USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 int usbDescriptorStringSerialNumber[];
 
@@ -501,22 +523,22 @@ int usbDescriptorStringSerialNumber[];
 #if !defined __ASSEMBLER__ && (!defined USB_CFG_VENDOR_ID || !defined USB_CFG_DEVICE_ID)
 #warning "You should define USB_CFG_VENDOR_ID and USB_CFG_DEVICE_ID in usbconfig.h"
 /* If the user has not defined IDs, we default to obdev's free IDs.
- * See USBID-License.txt for details.
+ * See USB-IDs-for-free.txt for details.
  */
 #endif
 
 /* make sure we have a VID and PID defined, byte order is lowbyte, highbyte */
 #ifndef USB_CFG_VENDOR_ID
-#   define  USB_CFG_VENDOR_ID   0xc0, 0x16  /* 5824 in dec, stands for VOTI */
+#   define  USB_CFG_VENDOR_ID   0xc0, 0x16  /* = 0x16c0 = 5824 = voti.nl */
 #endif
 
 #ifndef USB_CFG_DEVICE_ID
 #   if USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH
-#       define USB_CFG_DEVICE_ID    0xdf, 0x05  /* 1503 in dec, shared PID for HIDs */
+#       define USB_CFG_DEVICE_ID    0xdf, 0x05  /* = 0x5df = 1503, shared PID for HIDs */
 #   elif USB_CFG_INTERFACE_CLASS == 2
-#       define USB_CFG_DEVICE_ID    0xe1, 0x05  /* 1505 in dec, shared PID for CDC Modems */
+#       define USB_CFG_DEVICE_ID    0xe1, 0x05  /* = 0x5e1 = 1505, shared PID for CDC Modems */
 #   else
-#       define USB_CFG_DEVICE_ID    0xdc, 0x05  /* 1500 in dec, obdev's free PID */
+#       define USB_CFG_DEVICE_ID    0xdc, 0x05  /* = 0x5dc = 1500, obdev's free PID */
 #   endif
 #endif
 
@@ -546,6 +568,10 @@ int usbDescriptorStringSerialNumber[];
 #define USB_CFG_EP3_NUMBER  3
 #endif
 
+#ifndef USB_CFG_HAVE_INTRIN_ENDPOINT3
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3   0
+#endif
+
 #define USB_BUFSIZE     11  /* PID, 8 bytes data, 2 bytes CRC */
 
 /* ----- Try to find registers and bits responsible for ext interrupt 0 ----- */
@@ -558,7 +584,14 @@ int usbDescriptorStringSerialNumber[];
 #   endif
 #endif
 #ifndef USB_INTR_CFG_SET    /* allow user to override our default */
-#   define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01))    /* cfg for rising edge */
+#   if defined(USB_COUNT_SOF) || defined(USB_SOF_HOOK)
+#       define USB_INTR_CFG_SET (1 << ISC01)                    /* cfg for falling edge */
+        /* If any SOF logic is used, the interrupt must be wired to D- where
+         * we better trigger on falling edge
+         */
+#   else
+#       define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01))   /* cfg for rising edge */
+#   endif
 #endif
 #ifndef USB_INTR_CFG_CLR    /* allow user to override our default */
 #   define USB_INTR_CFG_CLR 0    /* no bits to clear */
@@ -695,7 +728,8 @@ typedef struct usbRequest{
 #define USBDESCR_HID_REPORT     0x22
 #define USBDESCR_HID_PHYS       0x23
 
-#define USBATTR_BUSPOWER        0x80
+//#define USBATTR_BUSPOWER        0x80  // USB 1.1 does not define this value any more
+#define USBATTR_BUSPOWER        0
 #define USBATTR_SELFPOWER       0x40
 #define USBATTR_REMOTEWAKE      0x20
 

avr/bootloader/usbdrv/usbdrvasm.S

@@ -1,11 +1,10 @@
 /* Name: usbdrvasm.S
- * Project: AVR USB driver
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
  * Author: Christian Starkjohann
  * Creation Date: 2007-06-13
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id$
  */
 
 /*
@@ -15,16 +14,9 @@ general code (preprocessor acrobatics and CRC computation) and then includes
 the file appropriate for the given clock rate.
 */
 
-#include "iarcompat.h"
+#define __SFR_OFFSET 0      /* used by avr-libc's register definitions */
-#ifndef __IAR_SYSTEMS_ASM__
+#include "usbportability.h"
-    /* configs for io.h */
+#include "usbdrv.h"         /* for common defs */
-#   define __SFR_OFFSET 0
-#   define _VECTOR(N)   __vector_ ## N   /* io.h does not define this for asm */
-#   include <avr/io.h> /* for CPU I/O register definitions and vectors */
-#   define macro    .macro  /* GNU Assembler macro definition */
-#   define endm     .endm   /* End of GNU Assembler macro definition */
-#endif  /* __IAR_SYSTEMS_ASM__ */
-#include "usbdrv.h" /* for common defs */
 
 /* register names */
 #define x1      r16
@@ -33,24 +25,14 @@ the file appropriate for the given clock rate.
 #define cnt     r19
 #define x3      r20
 #define x4      r21
-#define bitcnt  r22
+#define x5		r22
+#define bitcnt  x5
 #define phase   x4
 #define leap    x4
 
 /* Some assembler dependent definitions and declarations: */
 
 #ifdef __IAR_SYSTEMS_ASM__
-
-#   define nop2     rjmp    $+2 /* jump to next instruction */
-#   define XL       r26
-#   define XH       r27
-#   define YL       r28
-#   define YH       r29
-#   define ZL       r30
-#   define ZH       r31
-#   define lo8(x)   LOW(x)
-#   define hi8(x)   (((x)>>8) & 0xff)   /* not HIGH to allow XLINK to make a proper range check */
-
     extern  usbRxBuf, usbDeviceAddr, usbNewDeviceAddr, usbInputBufOffset
     extern  usbCurrentTok, usbRxLen, usbRxToken, usbTxLen
     extern  usbTxBuf, usbTxStatus1, usbTxStatus3
@@ -73,10 +55,12 @@ the file appropriate for the given clock rate.
 
 #else /* __IAR_SYSTEMS_ASM__ */
 
-#   define nop2     rjmp    .+0 /* jump to next instruction */
-
 #   ifndef USB_INTR_VECTOR /* default to hardware interrupt INT0 */
-#       define USB_INTR_VECTOR  SIG_INTERRUPT0
+#       ifdef INT0_vect
+#           define USB_INTR_VECTOR  INT0_vect       // this is the "new" define for the vector
+#       else
+#           define USB_INTR_VECTOR  SIG_INTERRUPT0  // this is the "old" vector
+#       endif
 #   endif
     .text
     .global USB_INTR_VECTOR
@@ -158,16 +142,93 @@ RTMODEL "__rt_version", "3"
 
 #endif
 
-; extern unsigned usbCrc16(unsigned char *data, unsigned char len);
+#if USB_USE_FAST_CRC
-; data: r24/25
+
-; len: r22
+; This implementation is faster, but has bigger code size
+; Thanks to Slawomir Fras (BoskiDialer) for this code!
+; It implements the following C pseudo-code:
+; unsigned table(unsigned char x)
+; {
+; unsigned    value;
+; 
+;     value = (unsigned)x << 6;
+;     value ^= (unsigned)x << 7;
+;     if(parity(x))
+;         value ^= 0xc001;
+;     return value;
+; }
+; unsigned usbCrc16(unsigned char *argPtr, unsigned char argLen)
+; {
+; unsigned crc = 0xffff;
+; 
+;     while(argLen--)
+;         crc = table(lo8(crc) ^ *argPtr++) ^ hi8(crc);
+;     return ~crc;
+; }
+
+; extern unsigned usbCrc16(unsigned char *argPtr, unsigned char argLen);
+;   argPtr  r24+25 / r16+r17
+;   argLen  r22 / r18
 ; temp variables:
-;   r18: data byte
+;   byte    r18 / r22
-;   r19: bit counter
+;   scratch r23
-;   r20/21: polynomial
+;   resCrc  r24+r25 / r16+r17
-;   r23: scratch
+;   ptr     X / Z
-;   r24/25: crc-sum
+usbCrc16:
-;   r26/27=X: ptr
+    mov     ptrL, argPtrL
+    mov     ptrH, argPtrH
+    ldi     resCrcL, 0xFF
+    ldi     resCrcH, 0xFF
+    rjmp    usbCrc16LoopTest
+usbCrc16ByteLoop:
+    ld      byte, ptr+
+    eor     resCrcL, byte   ; resCrcL is now 'x' in table()
+    mov     byte, resCrcL   ; compute parity of 'x'
+    swap    byte
+    eor     byte, resCrcL
+    mov     scratch, byte
+    lsr     byte
+    lsr     byte
+    eor     byte, scratch
+    inc     byte
+    lsr     byte
+    andi    byte, 1         ; byte is now parity(x)
+    mov     scratch, resCrcL
+    mov     resCrcL, resCrcH
+    eor     resCrcL, byte   ; low byte of if(parity(x)) value ^= 0xc001;
+    neg     byte
+    andi    byte, 0xc0
+    mov     resCrcH, byte   ; high byte of if(parity(x)) value ^= 0xc001;
+    clr     byte
+    lsr     scratch
+    ror     byte
+    eor     resCrcH, scratch
+    eor     resCrcL, byte
+    lsr     scratch
+    ror     byte
+    eor     resCrcH, scratch
+    eor     resCrcL, byte
+usbCrc16LoopTest:
+    subi    argLen, 1
+    brsh    usbCrc16ByteLoop
+    com     resCrcL
+    com     resCrcH
+    ret
+
+#else   /* USB_USE_FAST_CRC */
+
+; This implementation is slower, but has less code size
+;
+; extern unsigned usbCrc16(unsigned char *argPtr, unsigned char argLen);
+;   argPtr  r24+25 / r16+r17
+;   argLen  r22 / r18
+; temp variables:
+;   byte    r18 / r22
+;   bitCnt  r19
+;   poly    r20+r21
+;   scratch r23
+;   resCrc  r24+r25 / r16+r17
+;   ptr     X / Z
 usbCrc16:
     mov     ptrL, argPtrL
     mov     ptrH, argPtrH
@@ -175,27 +236,30 @@ usbCrc16:
     ldi     resCrcH, 0
     ldi     polyL, lo8(0xa001)
     ldi     polyH, hi8(0xa001)
-    com     argLen      ; argLen = -argLen - 1
+    com     argLen      ; argLen = -argLen - 1: modified loop to ensure that carry is set
-crcByteLoop:
+    ldi     bitCnt, 0   ; loop counter with starnd condition = end condition
-    subi    argLen, -1
+    rjmp    usbCrcLoopEntry
-    brcc    crcReady    ; modified loop to ensure that carry is set below
+usbCrcByteLoop:
     ld      byte, ptr+
-    ldi     bitCnt, -8  ; strange loop counter to ensure that carry is set where we need it
     eor     resCrcL, byte
-crcBitLoop:
+usbCrcBitLoop:
-    ror     resCrcH     ; carry is always set here
+    ror     resCrcH     ; carry is always set here (see brcs jumps to here)
     ror     resCrcL
-    brcs    crcNoXor
+    brcs    usbCrcNoXor
     eor     resCrcL, polyL
     eor     resCrcH, polyH
-crcNoXor:
+usbCrcNoXor:
-    subi    bitCnt, -1
+    subi    bitCnt, 224 ; (8 * 224) % 256 = 0; this loop iterates 8 times
-    brcs    crcBitLoop
+    brcs    usbCrcBitLoop
-    rjmp    crcByteLoop
+usbCrcLoopEntry:
-crcReady:
+    subi    argLen, -1
+    brcs    usbCrcByteLoop
+usbCrcReady:
     ret
 ; Thanks to Reimar Doeffinger for optimizing this CRC routine!
 
+#endif /* USB_USE_FAST_CRC */
+
 ; extern unsigned usbCrc16Append(unsigned char *data, unsigned char len);
 usbCrc16Append:
     rcall   usbCrc16
@@ -296,19 +360,33 @@ usbMFTimeout:
 ;----------------------------------------------------------------------------
 
 #ifndef USB_CFG_CLOCK_KHZ
-#   define USB_CFG_CLOCK_KHZ 12000
+#   ifdef F_CPU
+#       define USB_CFG_CLOCK_KHZ (F_CPU/1000)
+#   else
+#       error "USB_CFG_CLOCK_KHZ not defined in usbconfig.h and no F_CPU set!"
+#   endif
 #endif
 
-#if USB_CFG_CLOCK_KHZ == 12000
+#if USB_CFG_CHECK_CRC   /* separate dispatcher for CRC type modules */
-#   include "usbdrvasm12.inc"
+#   if USB_CFG_CLOCK_KHZ == 18000
-#elif USB_CFG_CLOCK_KHZ == 15000
+#       include "usbdrvasm18-crc.inc"
-#   include "usbdrvasm15.inc"
+#   else
-#elif USB_CFG_CLOCK_KHZ == 16000
+#       error "USB_CFG_CLOCK_KHZ is not one of the supported crc-rates!"
-#   include "usbdrvasm16.inc"
+#   endif
-#elif USB_CFG_CLOCK_KHZ == 16500
+#else   /* USB_CFG_CHECK_CRC */
-#   include "usbdrvasm165.inc"
+#   if USB_CFG_CLOCK_KHZ == 12000
-#elif USB_CFG_CLOCK_KHZ == 20000
+#       include "usbdrvasm12.inc"
-#   include "usbdrvasm20.inc"
+#   elif USB_CFG_CLOCK_KHZ == 12800
-#else
+#       include "usbdrvasm128.inc"
-#   error "USB_CFG_CLOCK_KHZ is not one of the supported rates!"
+#   elif USB_CFG_CLOCK_KHZ == 15000
-#endif
+#       include "usbdrvasm15.inc"
+#   elif USB_CFG_CLOCK_KHZ == 16000
+#       include "usbdrvasm16.inc"
+#   elif USB_CFG_CLOCK_KHZ == 16500
+#       include "usbdrvasm165.inc"
+#   elif USB_CFG_CLOCK_KHZ == 20000
+#       include "usbdrvasm20.inc"
+#   else
+#       error "USB_CFG_CLOCK_KHZ is not one of the supported non-crc-rates!"
+#   endif
+#endif /* USB_CFG_CHECK_CRC */

avr/bootloader/usbdrv/usbdrvasm.asm

@@ -1,11 +1,10 @@
 /* Name: usbdrvasm.asm
- * Project: AVR USB driver
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
  * Author: Christian Starkjohann
  * Creation Date: 2006-03-01
  * Tabsize: 4
  * Copyright: (c) 2006 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id$
  */
 
 /*

avr/bootloader/usbdrv/usbdrvasm12.inc

@@ -1,11 +1,10 @@
 /* Name: usbdrvasm12.inc
- * Project: AVR USB driver
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
  * Author: Christian Starkjohann
  * Creation Date: 2004-12-29
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbdrvasm12.inc 483 2008-02-05 15:05:32Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the
@@ -48,10 +47,13 @@ USB_INTR_VECTOR:
 ;----------------------------------------------------------------------------
 ;sync byte (D-) pattern LSb to MSb: 01010100 [1 = idle = J, 0 = K]
 ;sync up with J to K edge during sync pattern -- use fastest possible loops
-;first part has no timeout because it waits for IDLE or SE1 (== disconnected)
+;The first part waits at most 1 bit long since we must be in sync pattern.
+;YL is guarenteed to be < 0x80 because I flag is clear. When we jump to
+;waitForJ, ensure that this prerequisite is met.
 waitForJ:
-    sbis    USBIN, USBMINUS ;1 [40] wait for D- == 1
+    inc     YL
-    rjmp    waitForJ        ;2
+    sbis    USBIN, USBMINUS
+    brne    waitForJ        ; just make sure we have ANY timeout
 waitForK:
 ;The following code results in a sampling window of 1/4 bit which meets the spec.
     sbis    USBIN, USBMINUS
@@ -69,6 +71,9 @@ waitForK:
     inc     YL
     sts     usbSofCount, YL
 #endif  /* USB_COUNT_SOF */
+#ifdef USB_SOF_HOOK
+    USB_SOF_HOOK
+#endif
     rjmp    sofError
 foundK:
 ;{3, 5} after falling D- edge, average delay: 4 cycles [we want 4 for center sampling]
@@ -250,12 +255,12 @@ macro POP_STANDARD ; 12 cycles
     pop     x1
     pop     shift
     pop     YH
-endm
+    endm
 macro POP_RETI     ; 5 cycles
     pop     YL
     out     SREG, YL
     pop     YL
-endm
+    endm
 
 #include "asmcommon.inc"
 
@@ -263,25 +268,16 @@ endm
 ; Transmitting data
 ;----------------------------------------------------------------------------
 
-bitstuff0:                  ;1 (for branch taken)
+txByteLoop:
-    eor     x1, x4          ;1
+txBitloop:
-    ldi     x2, 0           ;1
+stuffN1Delay:                   ;     [03]
-    out     USBOUT, x1      ;1 <-- out
+    ror     shift               ;[-5] [11] [59]
-    rjmp    didStuff0       ;2 branch back 2 cycles earlier
+    brcc    doExorN1            ;[-4]      [60]
-bitstuff1:                  ;1 (for branch taken)
+    subi    x4, 1               ;[-3]
-    eor     x1, x4          ;1
+    brne    commonN1            ;[-2]
-    rjmp    didStuff1       ;2 we know that C is clear, jump back to do OUT and ror 0 into x2
+    lsl     shift               ;[-1] compensate ror after rjmp stuffDelay
-bitstuff2:                  ;1 (for branch taken)
+    nop                         ;[00] stuffing consists of just waiting 8 cycles
-    eor     x1, x4          ;1
+    rjmp    stuffN1Delay        ;[01] after ror, C bit is reliably clear
-    rjmp    didStuff2       ;2 jump back 4 cycles earlier and do out and ror 0 into x2
-bitstuff3:                  ;1 (for branch taken)
-    eor     x1, x4          ;1
-    rjmp    didStuff3       ;2 jump back earlier and ror 0 into x2
-bitstuff4:                  ;1 (for branch taken)
-    eor     x1, x4          ;1
-    ldi     x2, 0           ;1
-    out     USBOUT, x1      ;1 <-- out
-    rjmp    didStuff4       ;2 jump back 2 cycles earlier
 
 sendNakAndReti:                 ;0 [-19] 19 cycles until SOP
     ldi     x3, USBPID_NAK      ;1 [-18]
@@ -306,122 +302,91 @@ usbSendX3:                      ;0 [-16]
 ;usbSend:
 ;pointer to data in 'Y'
 ;number of bytes in 'cnt' -- including sync byte
-;uses: x1...x4, shift, cnt, Y
+;uses: x1...x2, x4, shift, cnt, Y [x1 = mirror USBOUT, x2 = USBMASK, x4 = bitstuff cnt]
-;Numbers in brackets are time since first bit of sync pattern is sent
+;Numbers in brackets are time since first bit of sync pattern is sent (start of instruction)
-usbSendAndReti:             ;0 [-13] timing: 13 cycles until SOP
+usbSendAndReti:
-    in      x2, USBDDR      ;1 [-12]
+    in      x2, USBDDR          ;[-12] 12 cycles until SOP
-    ori     x2, USBMASK     ;1 [-11]
+    ori     x2, USBMASK         ;[-11]
-    sbi     USBOUT, USBMINUS;2 [-9] prepare idle state; D+ and D- must have been 0 (no pullups)
+    sbi     USBOUT, USBMINUS    ;[-10] prepare idle state; D+ and D- must have been 0 (no pullups)
-    in      x1, USBOUT      ;1 [-8] port mirror for tx loop
+    out     USBDDR, x2          ;[-8] <--- acquire bus
-    out     USBDDR, x2      ;1 [-7] <- acquire bus
+    in      x1, USBOUT          ;[-7] port mirror for tx loop
-; need not init x2 (bitstuff history) because sync starts with 0
+    ldi     shift, 0x40         ;[-6] sync byte is first byte sent (we enter loop after ror)
-    push    x4              ;2 [-5]
+    ldi     x2, USBMASK         ;[-5]
-    ldi     x4, USBMASK     ;1 [-4] exor mask
+    push    x4                  ;[-4]
-    ldi     shift, 0x80     ;1 [-3] sync byte is first byte sent
+doExorN1:
-txLoop:                     ;       [62]
+    eor     x1, x2              ;[-2] [06] [62]
-    sbrs    shift, 0        ;1 [-2] [62]
+    ldi     x4, 6               ;[-1] [07] [63]
-    eor     x1, x4          ;1 [-1] [63]
+commonN1:
-    out     USBOUT, x1      ;1 [0] <-- out bit 0
+stuffN2Delay:
-    ror     shift           ;1 [1]
+    out     USBOUT, x1          ;[00] [08] [64] <--- set bit
-    ror     x2              ;1 [2]
+    ror     shift               ;[01]
-didStuff0:
+    brcc    doExorN2            ;[02]
-    cpi     x2, 0xfc        ;1 [3]
+    subi    x4, 1               ;[03]
-    brsh    bitstuff0       ;1 [4]
+    brne    commonN2            ;[04]
-    sbrs    shift, 0        ;1 [5]
+    lsl     shift               ;[05] compensate ror after rjmp stuffDelay
-    eor     x1, x4          ;1 [6]
+    rjmp    stuffN2Delay        ;[06] after ror, C bit is reliably clear
-    ror     shift           ;1 [7]
+doExorN2:
-didStuff1:
+    eor     x1, x2              ;[04] [12]
-    out     USBOUT, x1      ;1 [8] <-- out bit 1
+    ldi     x4, 6               ;[05] [13]
-    ror     x2              ;1 [9]
+commonN2:
-    cpi     x2, 0xfc        ;1 [10]
+    nop                         ;[06] [14]
-    brsh    bitstuff1       ;1 [11]
+    subi    cnt, 171            ;[07] [15] trick: (3 * 171) & 0xff = 1
-    sbrs    shift, 0        ;1 [12]
+    out     USBOUT, x1          ;[08] [16] <--- set bit
-    eor     x1, x4          ;1 [13]
+    brcs    txBitloop           ;[09]      [25] [41]
-    ror     shift           ;1 [14]
+
-didStuff2:
+stuff6Delay:
-    ror     x2              ;1 [15]
+    ror     shift               ;[42] [50]
-    out     USBOUT, x1      ;1 [16] <-- out bit 2
+    brcc    doExor6             ;[43]
-    cpi     x2, 0xfc        ;1 [17]
+    subi    x4, 1               ;[44]
-    brsh    bitstuff2       ;1 [18]
+    brne    common6             ;[45]
-    sbrs    shift, 0        ;1 [19]
+    lsl     shift               ;[46] compensate ror after rjmp stuffDelay
-    eor     x1, x4          ;1 [20]
+    nop                         ;[47] stuffing consists of just waiting 8 cycles
-    ror     shift           ;1 [21]
+    rjmp    stuff6Delay         ;[48] after ror, C bit is reliably clear
-didStuff3:
+doExor6:
-    ror     x2              ;1 [22]
+    eor     x1, x2              ;[45] [53]
-    cpi     x2, 0xfc        ;1 [23]
+    ldi     x4, 6               ;[46]
-    out     USBOUT, x1      ;1 [24] <-- out bit 3
+common6:
-    brsh    bitstuff3       ;1 [25]
+stuff7Delay:
-    nop2                    ;2 [27]
+    ror     shift               ;[47] [55]
-    ld      x3, y+          ;2 [29]
+    out     USBOUT, x1          ;[48] <--- set bit
-    sbrs    shift, 0        ;1 [30]
+    brcc    doExor7             ;[49]
-    eor     x1, x4          ;1 [31]
+    subi    x4, 1               ;[50]
-    out     USBOUT, x1      ;1 [32] <-- out bit 4
+    brne    common7             ;[51]
-    ror     shift           ;1 [33]
+    lsl     shift               ;[52] compensate ror after rjmp stuffDelay
-    ror     x2              ;1 [34]
+    rjmp    stuff7Delay         ;[53] after ror, C bit is reliably clear
-didStuff4:
+doExor7:
-    cpi     x2, 0xfc        ;1 [35]
+    eor     x1, x2              ;[51] [59]
-    brsh    bitstuff4       ;1 [36]
+    ldi     x4, 6               ;[52]
-    sbrs    shift, 0        ;1 [37]
+common7:
-    eor     x1, x4          ;1 [38]
+    ld      shift, y+           ;[53]
-    ror     shift           ;1 [39]
+    tst     cnt                 ;[55]
-didStuff5:
+    out     USBOUT, x1          ;[56] <--- set bit
-    out     USBOUT, x1      ;1 [40] <-- out bit 5
+    brne    txByteLoop          ;[57]
-    ror     x2              ;1 [41]
+
-    cpi     x2, 0xfc        ;1 [42]
-    brsh    bitstuff5       ;1 [43]
-    sbrs    shift, 0        ;1 [44]
-    eor     x1, x4          ;1 [45]
-    ror     shift           ;1 [46]
-didStuff6:
-    ror     x2              ;1 [47]
-    out     USBOUT, x1      ;1 [48] <-- out bit 6
-    cpi     x2, 0xfc        ;1 [49]
-    brsh    bitstuff6       ;1 [50]
-    sbrs    shift, 0        ;1 [51]
-    eor     x1, x4          ;1 [52]
-    ror     shift           ;1 [53]
-didStuff7:
-    ror     x2              ;1 [54]
-    cpi     x2, 0xfc        ;1 [55]
-    out     USBOUT, x1      ;1 [56] <-- out bit 7
-    brsh    bitstuff7       ;1 [57]
-    mov     shift, x3       ;1 [58]
-    dec     cnt             ;1 [59]
-    brne    txLoop          ;1/2 [60/61]
 ;make SE0:
-    cbr     x1, USBMASK     ;1 [61] prepare SE0 [spec says EOP may be 15 to 18 cycles]
+    cbr     x1, USBMASK         ;[58] prepare SE0 [spec says EOP may be 15 to 18 cycles]
-    pop     x4              ;2 [63]
+    lds     x2, usbNewDeviceAddr;[59]
-;brackets are cycles from start of SE0 now
+    lsl     x2                  ;[61] we compare with left shifted address
-    out     USBOUT, x1      ;1 [0] <-- out SE0 -- from now 2 bits = 16 cycles until bus idle
+    subi    YL, 2 + 20          ;[62] Only assign address on data packets, not ACK/NAK in x3
+    sbci    YH, 0               ;[63]
+    out     USBOUT, x1          ;[00] <-- out SE0 -- from now 2 bits = 16 cycles until bus idle
 ;2006-03-06: moved transfer of new address to usbDeviceAddr from C-Code to asm:
 ;set address only after data packet was sent, not after handshake
-    lds     x2, usbNewDeviceAddr;2 [2]
+    breq    skipAddrAssign      ;[01]
-    lsl     x2;             ;1 [3] we compare with left shifted address
+    sts     usbDeviceAddr, x2   ; if not skipped: SE0 is one cycle longer
-    subi    YL, 20 + 2      ;1 [4] Only assign address on data packets, not ACK/NAK in x3
-    sbci    YH, 0           ;1 [5]
-    breq    skipAddrAssign  ;2 [7]
-    sts     usbDeviceAddr, x2; if not skipped: SE0 is one cycle longer
 skipAddrAssign:
 ;end of usbDeviceAddress transfer
-    ldi     x2, 1<<USB_INTR_PENDING_BIT;1 [8] int0 occurred during TX -- clear pending flag
+    ldi     x2, 1<<USB_INTR_PENDING_BIT;[03] int0 occurred during TX -- clear pending flag
-    USB_STORE_PENDING(x2)   ;1 [9]
+    USB_STORE_PENDING(x2)       ;[04]
-    ori     x1, USBIDLE     ;1 [10]
+    ori     x1, USBIDLE         ;[05]
-    in      x2, USBDDR      ;1 [11]
+    in      x2, USBDDR          ;[06]
-    cbr     x2, USBMASK     ;1 [12] set both pins to input
+    cbr     x2, USBMASK         ;[07] set both pins to input
-    mov     x3, x1          ;1 [13]
+    mov     x3, x1              ;[08]
-    cbr     x3, USBMASK     ;1 [14] configure no pullup on both pins
+    cbr     x3, USBMASK         ;[09] configure no pullup on both pins
-    out     USBOUT, x1      ;1 [15] <-- out J (idle) -- end of SE0 (EOP signal)
+    pop     x4                  ;[10]
-    out     USBDDR, x2      ;1 [16] <-- release bus now
+    nop2                        ;[12]
-    out     USBOUT, x3      ;1 [17] <-- ensure no pull-up resistors are active
+    nop2                        ;[14]
+    out     USBOUT, x1          ;[16] <-- out J (idle) -- end of SE0 (EOP signal)
+    out     USBDDR, x2          ;[17] <-- release bus now
+    out     USBOUT, x3          ;[18] <-- ensure no pull-up resistors are active
     rjmp    doReturn
-
-bitstuff5:                  ;1 (for branch taken)
-    eor     x1, x4          ;1
-    rjmp    didStuff5       ;2 same trick as in bitstuff1...
-bitstuff6:                  ;1 (for branch taken)
-    eor     x1, x4          ;1
-    rjmp    didStuff6       ;2 same trick as above...
-bitstuff7:                  ;1 (for branch taken)
-    eor     x1, x4          ;1
-    rjmp    didStuff7       ;2 same trick as above...
-

avr/bootloader/usbdrv/usbdrvasm128.inc

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2008 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbdrvasm128.inc 740 2009-04-13 18:23:31Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the
@@ -31,8 +30,9 @@ limitations:
 They typical range is 14.5 MHz and most AVRs can actually reach this rate.
 (2) Writing EEPROM and Flash may be unreliable (short data lifetime) since
 the write procedure is timed from the RC oscillator.
-(3) End Of Packet detection is between bit 0 and bit 1 where the EOP condition
+(3) End Of Packet detection (SE0) should be in bit 1, bit it is only checked
-may not be reliable when a hub is used. It should be in bit 1.
+if bits 0 and 1 both read as 0 on D- and D+ read as 0 in the middle. This may
+cause problems with old hubs which delay SE0 by up to one cycle.
 (4) Code size is much larger than that of the other modules.
 
 Since almost all of this code is timing critical, don't change unless you
@@ -217,8 +217,10 @@ unstuff0s:
     ifioclr USBIN, USBMINUS     ;[00]
     ifioset USBIN, USBPLUS      ;[01]
     rjmp    bit0IsClr           ;[02] executed if first expr false or second true
-jumpToSe0AndStore:
+se0AndStore:                    ; executed only if both bits 0
-    rjmp    se0AndStore         ;[03] executed only if both bits 0
+    st      y+, x1              ;[15/17] cycles after start of byte
+    rjmp    se0                 ;[17/19]
+
 bit0IsClr:
     ifrset  phase, USBMINUS     ;[04] check phase only if D- changed
     lpm                         ;[05]
@@ -228,7 +230,7 @@ bit1AfterClr:
     andi    phase, USBMASK      ;[08]
     ifioset USBIN, USBMINUS     ;[09] <--- sample 1
     rjmp    bit1IsSet           ;[10]
-    breq    jumpToSe0AndStore   ;[11]
+    breq    se0AndStore         ;[11] if D- was 0 in bits 0 AND 1 and D+ was 0 in between, we have SE0
     andi    shift, ~(7 << 1)    ;[12]
     in      phase, USBIN        ;[13] <- phase
     breq    unstuff1c           ;[14]
@@ -355,10 +357,6 @@ unstuff7c:
     nop                         ;[59]
     rjmp    bit7IsSet           ;[60]
 
-se0AndStore:
-    st      y+, x1              ;[15/17] cycles after start of byte
-    rjmp    se0                 ;[17/19]
-
 bit7IsClr:
     ifrset  phase, USBMINUS     ;[62] check phase only if D- changed
     lpm                         ;[63]
@@ -391,25 +389,24 @@ bit0IsSet:
     in      phase, USBIN        ;[06] <- phase (one cycle too late)
     ori     shift, 1 << 0       ;[07]
 bit1AfterSet:
-    andi    phase, USBMASK      ;[08]
+    andi    shift, ~(7 << 1)    ;[08] compensated by "ori shift, 1<<1" if bit1IsClr
     ifioclr USBIN, USBMINUS     ;[09] <--- sample 1
     rjmp    bit1IsClr           ;[10]
-    andi    shift, ~(7 << 1)    ;[11]
+    breq    unstuff1s           ;[11]
-    breq    unstuff1s           ;[12]
+    nop2                        ;[12] do not check for SE0 if bit 0 was 1
-    in      phase, USBIN        ;[13] <- phase
+    in      phase, USBIN        ;[14] <- phase (one cycle too late)
-    nop                         ;[14]
     rjmp    bit2AfterSet        ;[15]
 unstuff1s:
-    in      phase, USBIN        ;[14] <- phase (one cycle too late)
+    in      phase, USBIN        ;[13] <- phase
-    andi    fix, ~(1 << 1)      ;[15]
+    andi    fix, ~(1 << 1)      ;[14]
-    nop2                        ;[08]
+    lpm                         ;[07]
     nop2                        ;[10]
 bit1IsClr:
     ifrset  phase, USBMINUS     ;[12] check phase only if D- changed
     lpm                         ;[13]
     in      phase, USBIN        ;[14] <- phase (one cycle too late)
-    breq    se0AndStore         ;[15] if we come from unstuff1s, Z bit is never set
+    ori     shift, 1 << 1       ;[15]
-    ori     shift, 1 << 1       ;[16]
+    nop                         ;[16]
 bit2AfterClr:
     ifioset USBIN, USBMINUS     ;[17] <--- sample 2
     rjmp    bit2IsSet           ;[18]

avr/bootloader/usbdrv/usbdrvasm15.inc

@@ -1,11 +1,10 @@
 /* Name: usbdrvasm15.inc
- * Project: AVR USB driver
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
  * Author: contributed by V. Bosch
  * Creation Date: 2007-08-06
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id: usbdrvasm15.inc 607 2008-05-13 15:57:28Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the
@@ -43,11 +42,13 @@ USB_INTR_VECTOR:
 ;
 ;   sync byte (D-) pattern LSb to MSb: 01010100 [1 = idle = J, 0 = K]
 ;   sync up with J to K edge during sync pattern -- use fastest possible loops
-;   first part has no timeout because it waits for IDLE or SE1 (== disconnected)
+;The first part waits at most 1 bit long since we must be in sync pattern.
-;-------------------------------------------------------------------------------
+;YL is guarenteed to be < 0x80 because I flag is clear. When we jump to
-waitForJ:			 ;- 
+;waitForJ, ensure that this prerequisite is met.
-    sbis    USBIN, USBMINUS      ;1 <-- sample: wait for D- == 1
+waitForJ:
-    rjmp    waitForJ		 ;2 
+    inc     YL
+    sbis    USBIN, USBMINUS
+    brne    waitForJ        ; just make sure we have ANY timeout
 ;-------------------------------------------------------------------------------
 ; The following code results in a sampling window of < 1/4 bit 
 ;	which meets the spec.
@@ -70,6 +71,9 @@ waitForK:			 ;-
     inc     YL
     sts     usbSofCount, YL
 #endif  /* USB_COUNT_SOF */
+#ifdef USB_SOF_HOOK
+    USB_SOF_HOOK
+#endif
     rjmp    sofError
 ;------------------------------------------------------------------------------
 ; {3, 5} after falling D- edge, average delay: 4 cycles [we want 5 for 
@@ -289,12 +293,12 @@ macro POP_STANDARD ; 16 cycles
     pop     x1
     pop     shift
     pop     YH
-endm
+    endm
 macro POP_RETI     ; 5 cycles
     pop     YL
     out     SREG, YL
     pop     YL
-endm
+    endm
 
 #include "asmcommon.inc"
 

avr/bootloader/usbdrv/usbdrvasm16.inc

@@ -1,11 +1,10 @@
 /* Name: usbdrvasm16.inc
- * Project: AVR USB driver
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
  * Author: Christian Starkjohann
  * Creation Date: 2007-06-15
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id: usbdrvasm16.inc 607 2008-05-13 15:57:28Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the
@@ -41,10 +40,13 @@ USB_INTR_VECTOR:
 ;----------------------------------------------------------------------------
 ;sync byte (D-) pattern LSb to MSb: 01010100 [1 = idle = J, 0 = K]
 ;sync up with J to K edge during sync pattern -- use fastest possible loops
-;first part has no timeout because it waits for IDLE or SE1 (== disconnected)
+;The first part waits at most 1 bit long since we must be in sync pattern.
+;YL is guarenteed to be < 0x80 because I flag is clear. When we jump to
+;waitForJ, ensure that this prerequisite is met.
 waitForJ:
-    sbis    USBIN, USBMINUS     ;[-18] wait for D- == 1
+    inc     YL
-    rjmp    waitForJ
+    sbis    USBIN, USBMINUS
+    brne    waitForJ        ; just make sure we have ANY timeout
 waitForK:
 ;The following code results in a sampling window of < 1/4 bit which meets the spec.
     sbis    USBIN, USBMINUS     ;[-15]
@@ -64,6 +66,9 @@ waitForK:
     inc     YL
     sts     usbSofCount, YL
 #endif  /* USB_COUNT_SOF */
+#ifdef USB_SOF_HOOK
+    USB_SOF_HOOK
+#endif
     rjmp    sofError
 foundK:                         ;[-12]
 ;{3, 5} after falling D- edge, average delay: 4 cycles [we want 5 for center sampling]
@@ -111,12 +116,15 @@ haveTwoBitsK:
 ; Receiver loop (numbers in brackets are cycles within byte after instr)
 ;----------------------------------------------------------------------------
 
+; duration of unstuffing code should be 10.66666667 cycles. We adjust "leap"
+; accordingly to approximate this value in the long run.
+
 unstuff6:
     andi    x2, USBMASK ;[03]
     ori     x3, 1<<6    ;[04] will not be shifted any more
     andi    shift, ~0x80;[05]
     mov     x1, x2      ;[06] sampled bit 7 is actually re-sampled bit 6
-    subi    leap, 3     ;[07] since this is a short (10 cycle) bit, enforce leap bit
+    subi    leap, -1    ;[07] total duration = 11 bits -> subtract 1/3
     rjmp    didUnstuff6 ;[08]
 
 unstuff7:
@@ -124,7 +132,7 @@ unstuff7:
     in      x2, USBIN   ;[00] [10]  re-sample bit 7
     andi    x2, USBMASK ;[01]
     andi    shift, ~0x80;[02]
-    subi    leap, 3     ;[03] since this is a short (10 cycle) bit, enforce leap bit
+    subi    leap, 2     ;[03] total duration = 10 bits -> add 1/3
     rjmp    didUnstuff7 ;[04]
 
 unstuffEven:
@@ -133,8 +141,8 @@ unstuffEven:
     andi    shift, ~0x80;[01]
     andi    x1, USBMASK ;[02]
     breq    se0         ;[03]
-    subi    leap, 3     ;[04] since this is a short (10 cycle) bit, enforce leap bit
+    subi    leap, -1    ;[04] total duration = 11 bits -> subtract 1/3
-    nop                 ;[05]
+    nop2                ;[05]
     rjmp    didUnstuffE ;[06]
 
 unstuffOdd:
@@ -143,8 +151,8 @@ unstuffOdd:
     andi    shift, ~0x80;[01]
     andi    x2, USBMASK ;[02]
     breq    se0         ;[03]
-    subi    leap, 3     ;[04] since this is a short (10 cycle) bit, enforce leap bit
+    subi    leap, -1    ;[04] total duration = 11 bits -> subtract 1/3
-    nop                 ;[05]
+    nop2                ;[05]
     rjmp    didUnstuffO ;[06]
 
 rxByteLoop:
@@ -208,13 +216,13 @@ macro POP_STANDARD ; 14 cycles
     pop     x1
     pop     shift
     pop     bitcnt
-endm
+    endm
 macro POP_RETI     ; 7 cycles
     pop     YH
     pop     YL
     out     SREG, YL
     pop     YL
-endm
+    endm
 
 #include "asmcommon.inc"
 

avr/bootloader/usbdrv/usbdrvasm165.inc

@@ -1,11 +1,10 @@
 /* Name: usbdrvasm165.inc
- * Project: AVR USB driver
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
  * Author: Christian Starkjohann
  * Creation Date: 2007-04-22
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id: usbdrvasm165.inc 607 2008-05-13 15:57:28Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the
@@ -46,10 +45,13 @@ USB_INTR_VECTOR:
 ;----------------------------------------------------------------------------
 ;sync byte (D-) pattern LSb to MSb: 01010100 [1 = idle = J, 0 = K]
 ;sync up with J to K edge during sync pattern -- use fastest possible loops
-;first part has no timeout because it waits for IDLE or SE1 (== disconnected)
+;The first part waits at most 1 bit long since we must be in sync pattern.
+;YL is guarenteed to be < 0x80 because I flag is clear. When we jump to
+;waitForJ, ensure that this prerequisite is met.
 waitForJ:
-    sbis    USBIN, USBMINUS     ;[-18] wait for D- == 1
+    inc     YL
-    rjmp    waitForJ
+    sbis    USBIN, USBMINUS
+    brne    waitForJ        ; just make sure we have ANY timeout
 waitForK:
 ;The following code results in a sampling window of < 1/4 bit which meets the spec.
     sbis    USBIN, USBMINUS     ;[-15]
@@ -69,6 +71,9 @@ waitForK:
     inc     YL
     sts     usbSofCount, YL
 #endif  /* USB_COUNT_SOF */
+#ifdef USB_SOF_HOOK
+    USB_SOF_HOOK
+#endif
     rjmp    sofError
 foundK:                         ;[-12]
 ;{3, 5} after falling D- edge, average delay: 4 cycles [we want 5 for center sampling]
@@ -334,12 +339,12 @@ macro POP_STANDARD ; 16 cycles
     pop     shift
     pop     YH
     pop     r0
-endm
+    endm
 macro POP_RETI     ; 5 cycles
     pop     YL
     out     SREG, YL
     pop     YL
-endm
+    endm
 
 #include "asmcommon.inc"
 

avr/bootloader/usbdrv/usbdrvasm18-crc.inc

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2008 by Lukas Schrittwieser and OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id: usbdrvasm18-crc.inc 740 2009-04-13 18:23:31Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the

avr/bootloader/usbdrv/usbdrvasm20.inc

@@ -1,12 +1,11 @@
 /* Name: usbdrvasm20.inc
- * Project: AVR USB driver
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
  * Author: Jeroen Benschop
  * Based on usbdrvasm16.inc from Christian Starkjohann
  * Creation Date: 2008-03-05
  * Tabsize: 4
  * Copyright: (c) 2008 by Jeroen Benschop and OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id: usbdrvasm20.inc 607 2008-05-13 15:57:28Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the
@@ -57,10 +56,13 @@ USB_INTR_VECTOR:
 ;----------------------------------------------------------------------------
 ;sync byte (D-) pattern LSb to MSb: 01010100 [1 = idle = J, 0 = K]
 ;sync up with J to K edge during sync pattern -- use fastest possible loops
-;first part has no timeout because it waits for IDLE or SE1 (== disconnected)
+;The first part waits at most 1 bit long since we must be in sync pattern.
+;YL is guarenteed to be < 0x80 because I flag is clear. When we jump to
+;waitForJ, ensure that this prerequisite is met.
 waitForJ:
-    sbis    USBIN, USBMINUS     ;[-21] wait for D- == 1
+    inc     YL
-    rjmp    waitForJ
+    sbis    USBIN, USBMINUS
+    brne    waitForJ        ; just make sure we have ANY timeout
 waitForK:
 ;The following code results in a sampling window of < 1/4 bit which meets the spec.
     sbis    USBIN, USBMINUS     ;[-19]
@@ -86,6 +88,9 @@ waitForK:
     inc     YL
     sts     usbSofCount, YL
 #endif  /* USB_COUNT_SOF */
+#ifdef USB_SOF_HOOK
+    USB_SOF_HOOK
+#endif
     rjmp    sofError
 foundK:                         ;[-16]
 ;{3, 5} after falling D- edge, average delay: 4 cycles
@@ -232,13 +237,13 @@ macro POP_STANDARD ; 14 cycles
     pop     x1
     pop     shift
     pop     bitcnt
-endm
+    endm
 macro POP_RETI     ; 7 cycles
     pop     YH
     pop     YL
     out     SREG, YL
     pop     YL
-endm
+    endm
 
 
 

avr/bootloader/usbdrv/usbportability.h

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2008 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbportability.h 740 2009-04-13 18:23:31Z cs $
  */
 
 /*
@@ -125,7 +124,11 @@ static inline void  sei(void)
 #   include <avr/pgmspace.h>
 #endif
 
-#define USB_READ_FLASH(addr)    pgm_read_byte(addr)
+#if USB_CFG_DRIVER_FLASH_PAGE
+#   define USB_READ_FLASH(addr)    pgm_read_byte_far(((long)USB_CFG_DRIVER_FLASH_PAGE << 16) | (long)(addr))
+#else
+#   define USB_READ_FLASH(addr)    pgm_read_byte(addr)
+#endif
 
 #define macro   .macro
 #define endm    .endm

avr/usbload/Makefile

@@ -19,27 +19,56 @@
 DEBUG   = 1
 TTY     = /dev/tty.PL2303-00002126
 DEVICE  = atmega644
-F_CPU   = 20000000	# in Hz
+F_CPU   = 20000000
 TARGET  = main
 AVRDUDE = avrdude -c usbasp -p $(DEVICE)
 SIZE    = avr-size
-
+BOOT_LOADER = 1
-
+BOOT_COMPRESS = rle
+BOOT_ROM01  = ../../roms/qd16boot_ver01.smc
+BOOT_ROM02  = ../../roms/qd16boot_ver02.smc
 
 
 ifeq ($(DEBUG),1)
-    LDFLAGS =  -Wl,-u,vfprintf -lprintf_flt 
+    BOOT_DEBUG = debug
-    CFLAGS  = -Iusbdrv -I. -DDEBUG_LEVEL=0 
+    LDFLAGS =-Wl,-u,vfprintf  
+    CFLAGS  =-Iusbdrv -I. -DDEBUG_LEVEL=0 
     OBJECTS = usbdrv/usbdrv.o usbdrv/usbdrvasm.o usbdrv/oddebug.o \
-               main.o usb_bulk.o uart.o fifo.o sram.o crc.o debug.o \
+               main.o usb_bulk.o uart.o fifo.o sram.o debug.o \
-               dump.o timer.o watchdog.o rle.c loader.o info.o shared_memory.o \
+dump.o timer.o watchdog.o loader.o info.o shared_memory.o crc.o \
-               command.o testing.o
+               system.o pwm.o util.o shell.o irq.o command.o 
 else 
-    LDFLAGS =  -Wl,-u
+    BOOT_DEBUG = nodebug
-    CFLAGS  = -Iusbdrv -I. -DDEBUG_LEVEL=0 -DNO_DEBUG -DNO_INFO
+    LDFLAGS =
+    CFLAGS  =-Iusbdrv -I. -DDEBUG_LEVEL=0 -DNO_DEBUG -DNO_INFO 
     OBJECTS = usbdrv/usbdrv.o usbdrv/usbdrvasm.o usbdrv/oddebug.o  main.o usb_bulk.o \
-              uart.o fifo.o sram.o crc.o debug.o dump.o timer.o watchdog.o rle.c loader.o \
+              sram.o crc.o debug.o dump.o loader.o \
-              info.o shared_memory.o command.o
+              system.o util.o info.o shared_memory.o command.o irq.o \
+              pwm.o
+endif
+
+ifeq ($(BOOT_LOADER), 1)
+	BOOT_ROM = $(BOOT_ROM01)
+else
+	BOOT_ROM = $(BOOT_ROM02)
+endif 
+
+ifeq ($(BOOT_COMPRESS), rle)
+	BOOT_CONVERTER = python ../../scripts/conv_rle.py
+	CFLAGS += -DBOOT_COMPRESS_RLE 
+	OBJECTS += rle.o 
+endif 
+
+ifeq ($(BOOT_COMPRESS), zip)
+	BOOT_CONVERTER = python ../../scripts/conv_zip.py
+	CFLAGS += -DBOOT_COMPRESS_ZIP
+	OBJECTS += neginf/neginf.o
+endif 
+
+ifeq ($(BOOT_COMPRESS), fastlz)
+	BOOT_CONVERTER = python ../../scripts/conv_fastlz.py
+	CFLAGS += -DBOOT_COMPRESS_FASTLZ
+	OBJECTS += fastlz.o 
 endif 
 
 COMPILE = avr-gcc -Wall -Os -DF_CPU=$(F_CPU) $(CFLAGS) -mmcu=$(DEVICE)
@@ -56,19 +85,13 @@ all: hex
 help:
 	@echo "This Makefile has no default rule. Use one of the following:"
 	@echo "make hex ....... to build main.hex"
-	@echo "make program ... to flash fuses and firmware"
 	@echo "make fuse ...... to flash the fuses"
 	@echo "make flash ..... to flash the firmware (use this on metaboard)"
 	@echo "make clean ..... to delete objects and hex file"
 
 hex: main.hex
-	@echo "==============================="
 	@echo "$(TARGET) compiled for: $(DEVICE)"
-	@echo -n "size is: "
+	@./checksize $(TARGET).elf
-	@$(SIZE) -A $(TARGET).hex | grep "\.sec1" | tr -s " " | cut -d" " -f2
-	@echo "==============================="
-
-program: flash fuse
 
 # rule for programming fuse bits:
 fuse:
@@ -79,6 +102,11 @@ fuse:
 flash: main.hex
 	$(AVRDUDE) -U flash:w:main.hex:i
 
+convert-boot-rom:
+	$(BOOT_CONVERTER) $(BOOT_ROM) 
+
+release: main.hex
+	cp -v main.hex ../../files/firmware/firmware-loader0$(BOOT_LOADER)-$(BOOT_COMPRESS)-$(BOOT_DEBUG)-$$(date +%Y%m%d).hex 
 
 .c.o:
 	$(COMPILE) -c $< -o $@

avr/usbload/checksize

@@ -5,11 +5,11 @@
 # Creation Date: 2004-12-29
 # Tabsize: 4
 # Copyright: (c) 2005 OBJECTIVE DEVELOPMENT Software GmbH.
-# Revision: $Id: checksize 83 2006-01-05 22:20:53Z cs $
+# Revision: $:Id: checksize 83 2006-01-05 22:20:53Z cs $
 
 error=0
-codelimit=16384  # default value
+codelimit=65536  # default value
-datalimit=992   # default value; leave 32 bytes for stack
+datalimit=4064   # default value; leave 32 bytes for stack
 
 if [ $# -gt 1 ]; then
 	codelimit="$2"

avr/usbload/command.c

@@ -18,7 +18,7 @@
  * =====================================================================================
  */
 
-#include <avr/io.h>
+#include <avr/interrupt.h>
 #include <util/delay.h>
 #include <stdlib.h>
 
@@ -26,36 +26,174 @@
 #include "requests.h"
 #include "sram.h"
 #include "info.h"
+#include "irq.h"
+#include "usbdrv.h"
 
-extern uint32_t req_bank_size;
+#if defined(BOOT_COMPRESS_RLE) 
+#include "rle.h"
+#endif 
+
+#if defined(BOOT_COMPRESS_ZIP) 
+#include "neginf/neginf.h"
+#include "inflate.h"
+#endif 
+
+#if defined(BOOT_COMPRESS_FASTLZ) 
+#include "fastlz.h"
+#endif 
+
+#include "loader.h"
+#include "system.h"
 
 
-void send_reset()
+extern usb_transaction_t usb_trans;
+extern system_t my_system;
+
+extern const char *_rom[];
+extern const char _rom01[];
+extern const int _rom_size[];
+
+void usb_connect()
 {
-    info("Reset Snes\n");
+    uint8_t i = 0;
-    snes_reset_on();
+    info_P(PSTR("USB init\n"));
-    snes_reset_lo();
+    usbDeviceDisconnect();      /* enforce re-enumeration, do this while */
-    _delay_ms(2);
+    cli();
-    snes_reset_hi();
+    info_P(PSTR("USB disconnect\n"));
-    snes_reset_off();
+    i = 10;
-}
+    while (--i) {               /* fake USB disconnect for > 250 ms */
-
+        _delay_ms(50);
-void send_irq()
-{
-    snes_irq_on();
-    snes_irq_lo();
-    _delay_us(20);
-    snes_irq_hi();
-    snes_irq_off();
-}
-
-void set_rom_mode()
-{
-    if (req_bank_size == 0x8000) {
-        snes_lorom();
-        info("Set Snes lowrom \n");
-    } else {
-        snes_hirom();
-        info("Set Snes hirom \n");
     }
+    led_on();
+    usbDeviceConnect();
+    info_P(PSTR("USB connect\n"));
+}
+
+
+
+void boot_startup_rom(uint16_t init_delay)
+{
+    uint8_t i;
+
+#if defined(BOOT_COMPRESS_RLE) 
+    uint32_t addr = 0x000000;
+#endif 
+
+#if defined(BOOT_COMPRESS_ZIP) 
+    uint8_t c;
+    uint16_t j;
+    PGM_VOID_P p_addr;
+#endif 
+    
+    info_P(PSTR("Fetch Loader: %s from AVR PROGMEM\n"), LOADER_NAME);
+
+    system_set_bus_avr();
+    // snes_irq_lo();
+    // system_snes_irq_off();
+    system_set_rom_lorom();
+
+    // info_P(PSTR("Activate AVR bus\n"));
+    // avr_bus_active();
+    // info_P(PSTR("IRQ off\n"));
+    // snes_irq_lo();
+    // snes_irq_off();
+    // snes_lorom();
+
+    info_P(PSTR("Unpack Loader with using method: %s\n"), LOADER_COMPRESS);
+#if defined(BOOT_COMPRESS_RLE) 
+    for (i = 0; i < ROM_BUFFER_CNT; i++) {
+        addr += rle_decode(_rom[i], _rom_size[i], addr);
+    }
+#endif 
+
+#if defined(BOOT_COMPRESS_ZIP) 
+    //inflate_init();
+    neginf_init(0);
+    for (i=0; i<ROM_BUFFER_CNT; i++){
+        p_addr = _rom[i];
+        info_P(PSTR("idx=%i addr=%lx %s\n"), i, p_addr);
+        for (j=0; j<_rom_size[i]; j++){
+            c = pgm_read_byte((PGM_VOID_P)p_addr++); 
+            neginf_process_byte(c);
+            
+        }
+    }
+#endif 
+
+#if defined(BOOT_COMPRESS_FASTLZ) 
+    uint32_t rlen = _rom_size[0]+ _rom_size[1];
+    fastlz_decompress2(_rom[0], _rom[0], rlen);
+#endif 
+
+    info_P(PSTR("\n"));
+    
+
+#if DO_CRC_CHECK_LOADER
+    dump_memory(0x010000 - 0x100, 0x010000);
+    uint16_t crc;
+    crc = crc_check_bulk_memory((uint32_t) 0x000000, 0x010000, 0x010000);
+    info(PSTR("crc=%x\n"), crc);
+#endif
+
+    // snes_irq_lo();
+    // snes_irq_off();
+    // snes_hirom();
+    // snes_wr_disable();
+
+    // system_set_bus_snes();
+    // system_set_rom_hirom();
+    // system_set_wr_disable();
+    // system_snes_irq_off();
+
+    snes_irq_lo();
+    system_snes_irq_off();
+    system_set_rom_hirom();
+    system_set_wr_disable();
+    system_set_bus_snes();
+
+
+    system_send_snes_reset();
+    info_P(PSTR("Move Loader to wram"));
+    for (i = 0; i < 30; i++) {
+        _delay_ms(20);
+        info_P(PSTR("."));
+    }
+    info_P(PSTR("\n"));
+}
+
+void banner()
+{
+    uint8_t i;
+    for (i = 0; i < 40; i++)
+        info_P(PSTR("\n"));
+    info_P(PSTR
+           (" ________        .__        __    ________               ____  ________\n"));
+    info_P(PSTR
+           (" \\_____  \\  __ __|__| ____ |  | __\\______ \\   _______  _/_   |/  _____/\n"));
+    info_P(PSTR
+           ("  /  / \\  \\|  |  \\  |/ ___\\|  |/ / |    |  \\_/ __ \\  \\/ /|   /   __  \\ \n"));
+    info_P(PSTR
+           (" /   \\_/.  \\  |  /  \\  \\___|    <  |    `   \\  ___/\\   / |   \\  |__\\  \\ \n"));
+    info_P(PSTR
+           (" \\_____\\ \\_/____/|__|\\___  >__|_ \\/_______  /\\___  >\\_/  |___|\\_____  / \n"));
+    info_P(PSTR
+           ("        \\__>             \\/     \\/        \\/     \\/                 \\/ \n"));
+    info_P(PSTR("\n"));
+    info_P(PSTR("                               www.optixx.org\n"));
+    info_P(PSTR("\n"));
+    info_P(PSTR("Hardware Version: %s Software Version: %s Build Date: %s \n"), HW_VERSION, SW_VERSION, __DATE__ );
+
+}
+
+void transaction_status()
+{
+    info_P(PSTR("\nAddr           0x%06lx\n"), usb_trans.req_addr);
+    info_P(PSTR("Bank           0x%02x\n"), usb_trans.req_bank);
+    info_P(PSTR("Banksize       0x%06lx\n"), usb_trans.req_bank_size);
+    info_P(PSTR("Bankcount      0x%02x\n"), usb_trans.req_bank_cnt);
+    info_P(PSTR("Status         0x%02x\n"), usb_trans.req_state);
+    info_P(PSTR("Percent        %02i\n"), usb_trans.req_percent);
+    info_P(PSTR("TX buffer      %02i\n"), usb_trans.tx_remaining);
+    info_P(PSTR("RX buffer      %02i\n"), usb_trans.rx_remaining);
+    info_P(PSTR("Syncerr        %02i\n"), usb_trans.sync_errors);
 }

avr/usbload/command.h

@@ -22,8 +22,10 @@
 #ifndef __COMMAND_H__
 #define __COMMAND_H__
 
-void send_reset();
+void usb_connect();
-void send_irq();
+void boot_startup_rom(uint16_t init_delay);
-void set_rom_mode();
+void banner();
+void transaction_status();
+
 
 #endif

avr/usbload/config.h

@@ -42,7 +42,17 @@
 #define USB_MAX_TRANS               0xff
 #define USB_CRC_CHECK               0x01
 
-#define TRANSFER_BUFFER_SIZE        0x200
+#define TRANSFER_BUFFER_SIZE        0x000
+#define FORMAT_BUFFER_LEN           0x080
+#define RECEIVE_BUF_LEN             0x030
+#define HW_VERSION                  "2.6"
+#define SW_VERSION                  "1.2"
 
+#define DO_CRC_CHECK_LOADER         0
+#define DO_CRC_CHECK                1
+#define DO_SHM_SCRATCHPAD           0
+#define DO_SHM                      0
+#define DO_TIMER                    1
+#define DO_SHELL                    1
 
 #endif

avr/usbload/crc.c

@@ -65,17 +65,24 @@ uint16_t do_crc_update(uint16_t crc, uint8_t * data, uint16_t size)
 }
 
 
-uint16_t crc_check_bulk_memory(uint32_t bottom_addr, uint32_t top_addr, uint32_t bank_size)
+uint16_t crc_check_bulk_memory(uint32_t bottom_addr, uint32_t top_addr,
+                               uint32_t bank_size)
 {
     uint16_t crc = 0;
     uint32_t addr = 0;
     uint8_t req_bank = 0;
     sram_bulk_read_start(bottom_addr);
+    debug_P(DEBUG_CRC,
+            PSTR
+            ("crc_check_bulk_memory: bottom_addr=0x%08lx top_addr=0x%08lx\n"),
+            bottom_addr, top_addr);
 
     for (addr = bottom_addr; addr < top_addr; addr++) {
-        if (addr && addr % bank_size == 0) {
+        if (addr && ((addr % bank_size) == 0)) {
-            debug(DEBUG_CRC,"crc_check_bulk_memory: bank=0x%02x addr=0x%08lx crc=0x%04x\n",
+            debug_P(DEBUG_CRC,
-                req_bank,addr,crc);
+                    PSTR
+                    ("crc_check_bulk_memory: bank=0x%02x addr=0x%08lx crc=0x%04x\n"),
+                    req_bank, addr, crc);
             req_bank++;
             crc = 0;
         }
@@ -83,8 +90,10 @@ uint16_t crc_check_bulk_memory(uint32_t bottom_addr, uint32_t top_addr, uint32_t
         sram_bulk_read_next();
     }
     if (addr % 0x8000 == 0)
-        debug(DEBUG_CRC,"crc_check_bulk_memory: bank=0x%02x addr=0x%08lx crc=0x%04x\n",
+        debug_P(DEBUG_CRC,
-            req_bank,addr,crc);
+                PSTR
+                ("crc_check_bulk_memory: bank=0x%02x addr=0x%08lx crc=0x%04x\n"),
+                req_bank, addr, crc);
     sram_bulk_read_end();
     return crc;
 }
@@ -92,12 +101,14 @@ uint16_t crc_check_bulk_memory(uint32_t bottom_addr, uint32_t top_addr, uint32_t
 
 
 
-uint16_t crc_check_memory_range(uint32_t start_addr, uint32_t size,uint8_t *buffer)
+uint16_t crc_check_memory_range(uint32_t start_addr, uint32_t size,
+                                uint8_t * buffer)
 {
     uint16_t crc = 0;
     uint32_t addr;
-    for (addr = start_addr; addr < start_addr + size; addr += TRANSFER_BUFFER_SIZE) {
+    for (addr = start_addr; addr < start_addr + size;
-        sram_bulk_read_buffer(addr, buffer, TRANSFER_BUFFER_SIZE);
+         addr += TRANSFER_BUFFER_SIZE) {
+        sram_bulk_copy_into_buffer(addr, buffer, TRANSFER_BUFFER_SIZE);
         crc = do_crc_update(crc, buffer, TRANSFER_BUFFER_SIZE);
     }
     return crc;

avr/usbload/crc.h

@@ -27,9 +27,11 @@
 
 
 uint16_t crc_xmodem_update(uint16_t crc, uint8_t data);
-uint16_t do_crc(uint8_t * data,uint16_t size);
+uint16_t do_crc(uint8_t * data, uint16_t size);
-uint16_t do_crc_update(uint16_t crc,uint8_t * data,uint16_t size);
+uint16_t do_crc_update(uint16_t crc, uint8_t * data, uint16_t size);
-uint16_t crc_check_memory_range(uint32_t start_addr, uint32_t size,uint8_t *buffer);
+uint16_t crc_check_memory_range(uint32_t start_addr, uint32_t size,
-uint16_t crc_check_bulk_memory(uint32_t bottom_addr, uint32_t bank_size,uint32_t top_addr);
+                                uint8_t * buffer);
+uint16_t crc_check_bulk_memory(uint32_t bottom_addr, uint32_t bank_size,
+                               uint32_t top_addr);
 
 #endif

avr/usbload/debug.c

@@ -20,19 +20,20 @@
 
 #include <stdlib.h>
 #include <stdint.h>
+#include <avr/pgmspace.h>
 
 #include "debug.h"
 #include "uart.h"
-
+#include "config.h"
-
 
 extern FILE uart_stdout;
 
-extern int debug_level; /* the higher, the more messages... */
+extern int debug_level;         /* the higher, the more messages... */
 
 #if defined(NO_DEBUG) && defined(__GNUC__)
 #else
-void debug(int level, char* format, ...) {
+void debug(int level, char *format, ...)
+{
 #ifdef NO_DEBUG
 
 #else
@@ -46,4 +47,24 @@ void debug(int level, char* format, ...) {
 }
 #endif
 
+#ifndef NO_INFO
+uint8_t buffer_debug[FORMAT_BUFFER_LEN];
+#endif
 
+#if defined(NO_DEBUG) && defined(__GNUC__)
+#else
+void debug_P(int level, PGM_P format, ...)
+{
+#ifdef NO_DEBUG
+
+#else
+    va_list args;
+    if (!(debug_level & level))
+        return;
+    strlcpy_P((char *) buffer_debug, format, FORMAT_BUFFER_LEN);
+    va_start(args, format);
+    vprintf((char *) buffer_debug, args);
+    va_end(args);
+#endif
+}
+#endif

avr/usbload/debug.h

@@ -26,18 +26,33 @@
 #include <stdlib.h>
 #include <stdint.h>
 #include <stdarg.h>
-
+#include <avr/pgmspace.h>
 
 #if defined(NO_DEBUG) && defined(__GNUC__)
-/* gcc's cpp has extensions; it allows for macros with a variable number of
+/*
-   arguments. We use this extension here to preprocess pmesg away. */
+ * gcc's cpp has extensions; it allows for macros with a variable number of arguments. We use this extension here to preprocess pmesg away. 
+ */
 #define debug(level, format, args...) ((void)0)
 #else
 void debug(int level, char *format, ...);
-/* print a message, if it is considered significant enough.
+/*
-      Adapted from [K&R2], p. 174 */
+ * print a message, if it is considered significant enough. Adapted from [K&R2], p. 174 
+ */
 #endif
 
 
-#endif /* DEBUG_H */
 
+#if defined(NO_DEBUG) && defined(__GNUC__)
+/*
+ * gcc's cpp has extensions; it allows for macros with a variable number of arguments. We use this extension here to preprocess pmesg away. 
+ */
+#define debug_P(level, format, args...) ((void)0)
+#else
+void debug_P(int level, PGM_P format, ...);
+/*
+ * print a message, if it is considered significant enough. Adapted from [K&R2], p. 174 
+ */
+#endif
+
+
+#endif                          /* DEBUG_H */

avr/usbload/dump.c

@@ -26,13 +26,14 @@
 #include "info.h"
 #include "uart.h"
 #include "sram.h"
+#include "dump.h"
 
 
 extern FILE uart_stdout;
 
 void dump_packet(uint32_t addr, uint32_t len, uint8_t * packet)
 {
-    uint16_t i,j;
+    uint16_t i, j;
     uint16_t sum = 0;
     uint8_t clear = 0;
 
@@ -47,21 +48,21 @@ void dump_packet(uint32_t addr, uint32_t len, uint8_t * packet)
             continue;
         }
         if (clear) {
-            info("*\n");
+            info_P(PSTR("*\n"));
             clear = 0;
         }
-        info("%08lx:", addr + i);
+        info_P(PSTR("%08lx:"), addr + i);
         for (j = 0; j < 16; j++) {
-            info(" %02x", packet[i + j]);
+            info_P(PSTR(" %02x"), packet[i + j]);
         }
-        info(" |");
+        info_P(PSTR(" |"));
         for (j = 0; j < 16; j++) {
             if (packet[i + j] >= 33 && packet[i + j] <= 126)
-                info("%c", packet[i + j]);
+                info_P(PSTR("%c"), packet[i + j]);
             else
-                info(".");
+                info_P(PSTR("."));
         }
-        info("|\n");
+        info_P(PSTR("|\n"));
     }
 }
 
@@ -70,13 +71,13 @@ void dump_memory(uint32_t bottom_addr, uint32_t top_addr)
     uint32_t addr;
     uint8_t byte;
     sram_bulk_read_start(bottom_addr);
-    for ( addr = bottom_addr; addr < top_addr; addr++) {
+    for (addr = bottom_addr; addr < top_addr; addr++) {
-        if (addr%0x10 == 0)
+        if (addr % 0x10 == 0)
-            info("\n%08lx:", addr);
+            info_P(PSTR("\n%08lx:"), addr);
         byte = sram_bulk_read();
         sram_bulk_read_next();
-        info(" %02x", byte);
+        info_P(PSTR(" %02x"), byte);
     }
-    info("\n");
+    info_P(PSTR("\n"));
     sram_bulk_read_end();
 }

avr/usbload/dump.h

@@ -28,7 +28,6 @@
 
 void dump_memory(uint32_t bottom_addr, uint32_t top_addr);
 
-void dump_packet(uint32_t addr,uint32_t len,uint8_t *packet);
+void dump_packet(uint32_t addr, uint32_t len, uint8_t * packet);
 
 #endif
-

avr/usbload/fastlz.c

@@ -0,0 +1,197 @@
+
+#if defined(__GNUC__) && (__GNUC__ > 2)
+#define FASTLZ_EXPECT_CONDITIONAL(c)    (__builtin_expect((c), 1))
+#define FASTLZ_UNEXPECT_CONDITIONAL(c)  (__builtin_expect((c), 0))
+#else
+#define FASTLZ_EXPECT_CONDITIONAL(c)    (c)
+#define FASTLZ_UNEXPECT_CONDITIONAL(c)  (c)
+#endif
+
+/*
+ * Use inlined functions for supported systems.
+ */
+#if defined(__GNUC__) || defined(__DMC__) || defined(__POCC__) || defined(__WATCOMC__) || defined(__SUNPRO_C)
+#define FASTLZ_INLINE inline
+#elif defined(__BORLANDC__) || defined(_MSC_VER) || defined(__LCC__)
+#define FASTLZ_INLINE __inline
+#else 
+#define FASTLZ_INLINE
+#endif
+
+typedef unsigned char  flzuint8;
+typedef unsigned short flzuint16;
+typedef unsigned int   flzuint32;
+
+/* prototypes */
+int fastlz_decompress(const void* input, int length, void* output);
+
+#define MAX_DISTANCE  256
+
+
+#include <avr/pgmspace.h>       /* required by usbdrv.h */
+#include <util/delay.h>         /* for _delay_ms() */
+#include <avr/interrupt.h>      /* for sei() */
+
+#include "sram.h"
+#include "debug.h"
+#include "info.h"
+#include "ringbuffer.h"
+
+//#define log2(NUM) printf("%i op=%i(%x) ip=%i(%x) ref=%i(%x) dist=%i buf->end=%i len=%i ctrl=%i ofs=%i(%i) limit=%i\n",NUM, output_index,output[output_index], input_index,input[input_index],ref_index,input[ref_index],output_index - ref_index,ref_buffer_ptr->end, len, ctrl, ofs, ofs>>6,input_index < ip_limit); 
+
+#define log2(NUM) info_P(PSTR("%i op=%i ip=%i ref=%i dist=%i buf->end=%i len=%i ctrl=%i ofs=%i(%i) limit=%i\n"),NUM, output_index, input_index,ref_index,output_index - ref_index,ref_buffer_ptr->end, len, ctrl, ofs, ofs>>6,input_index < ip_limit); 
+
+#define OUTPUT_INC(B)  do { \
+    __b = B;\
+    sram_bulk_write(__b);\
+    sram_bulk_write_next();\
+    bufferWrite(ref_buffer_ptr, __b);\
+    output_index++;\
+} while (0)
+
+#define OUTPUT_INC_FROM_REFINC()  do { \
+    __dist = (output_index-ref_index); \
+    __c = buffer_get(ref_buffer_ptr, __dist); \
+    sram_bulk_write(__c);\
+    sram_bulk_write_next();\
+    output_index++;\
+    bufferWrite(ref_buffer_ptr, __c);\
+    ref_index++;\
+} while (0)
+
+
+#define FROM_REF(OUT)  do { \
+    flzuint16 __dist = (output_index-ref_index+1); \
+    OUT = buffer_get(ref_buffer_ptr, __dist); \
+} while (0)
+
+#define OUTBYTE(OUT) do { \
+    sram_bulk_write(OUT);\
+    sram_bulk_write_next();\
+    output_index++;\
+} while(0)
+
+#define INBYTE(IN) do { \
+    cli();\
+    IN = pgm_read_byte((PGM_VOID_P)input_index++);  \
+    sei();\
+} while(0)
+
+#define INPUT_INC(IN)  do { \
+    cli();\
+    if (input_index<32768) { \
+        IN = pgm_read_byte((PGM_VOID_P)input_index++);  \
+    } else { \
+        IN = pgm_read_byte((PGM_VOID_P)input_index-32768);  \
+        input_index++; \
+    }\
+    sei();\
+} while (0)
+
+ring_buffer_typedef(unsigned char, byte_buffer);
+
+int fastlz_decompress2(unsigned char* input1, unsigned char* input2, int length)
+{
+  flzuint32 input_index = 0;
+  flzuint32 ip_limit = length;
+  flzuint32 output_index = 0;
+  flzuint32 ref_index = 0;
+  //flzuint32 ctrl = (input[input_index++]) & 31;
+  flzuint32 ctrl;
+  INPUT_INC(ctrl);
+  ctrl = ctrl & 31;
+
+
+
+  int loop = 1;
+
+  byte_buffer ref_buffer;
+  buffer_init(ref_buffer, MAX_DISTANCE, unsigned char);
+  byte_buffer* ref_buffer_ptr;
+  ref_buffer_ptr = &ref_buffer;
+
+  do
+  {
+    flzuint8 __b;
+    flzuint16 __dist;
+    flzuint8 __c; 
+    flzuint8 tmp;
+
+    ref_index = output_index;
+    flzuint32 len = ctrl >> 5;
+    flzuint32 ofs = (ctrl & 31) << 6;
+    //log2(1)
+    if(ctrl >= 32)
+    {
+      len--;
+      ref_index -= ofs;
+      if (len == 7-1){
+        INPUT_INC(tmp);
+        len += tmp;
+        //len += input[input_index++];
+      }
+      INPUT_INC(tmp);
+      ref_index -= tmp;
+      //ref_index -= input[input_index++];
+      
+      //log2(1)
+
+      if(FASTLZ_EXPECT_CONDITIONAL( input_index < ip_limit))
+        INPUT_INC(ctrl);
+        //ctrl = input[input_index++];
+      else
+        loop = 0;
+      
+      //log2(1)
+
+      if(ref_index == output_index)
+      {
+        //log2(2)
+        //flzuint8 b = output[ref_index-1];
+        flzuint8 b;
+        FROM_REF(b);
+        
+
+        OUTPUT_INC(b);
+        OUTPUT_INC(b);
+        OUTPUT_INC(b);
+        for(; len; --len)
+            OUTPUT_INC(b);
+      }
+      else
+      {
+        //log2(3)
+        ref_index--;
+        OUTPUT_INC_FROM_REFINC();
+        OUTPUT_INC_FROM_REFINC();
+        OUTPUT_INC_FROM_REFINC();
+        for(; len; --len)
+            OUTPUT_INC_FROM_REFINC();
+      }
+    }
+    else
+    {
+      ctrl++;
+      //log2(4)
+      INPUT_INC(tmp);
+      OUTPUT_INC(tmp);
+      //OUTPUT_INC(input[input_index++]);
+      for(--ctrl; ctrl; ctrl--){
+        //log2(5)
+        INPUT_INC(tmp);
+        OUTPUT_INC(tmp);
+        //OUTPUT_INC(input[input_index++]);
+    } 
+
+      loop = FASTLZ_EXPECT_CONDITIONAL(input_index < ip_limit);
+      if (loop){
+        INPUT_INC(ctrl);
+        //ctrl = input[input_index++];
+     }
+      //log2(6)
+    }
+  }
+  while(FASTLZ_EXPECT_CONDITIONAL(loop));
+  buffer_destroy(ref_buffer_ptr);
+  return 0;
+}

avr/usbload/fastlz.h

@@ -0,0 +1,14 @@
+#ifndef FASTLZ_H
+#define FASTLZ_H
+
+#define FASTLZ_VERSION 0x000100
+
+#define FASTLZ_VERSION_MAJOR     0
+#define FASTLZ_VERSION_MINOR     0
+#define FASTLZ_VERSION_REVISION  0
+
+#define FASTLZ_VERSION_STRING "0.1.0"
+
+int fastlz_decompress2(const void* input1, const void* input2, int length); 
+
+#endif /* FASTLZ_H */

avr/usbload/info.c

@@ -20,9 +20,12 @@
 
 #include <stdlib.h>
 #include <stdint.h>
+#include <avr/pgmspace.h>
 
 #include "info.h"
 #include "uart.h"
+#include "config.h"
+
 
 
 
@@ -34,7 +37,8 @@ extern FILE uart_stdout;
 #define info(format, args...) ((void)0)
 
 #else
-void info(char* format, ...) {
+void info(char *format, ...)
+{
 #ifdef NO_INFO
 
 #else
@@ -47,3 +51,25 @@ void info(char* format, ...) {
 #endif
 
 
+#ifndef NO_INFO
+uint8_t buffer_info[FORMAT_BUFFER_LEN];
+#endif
+
+#if defined(NO_INFO) && defined(__GNUC__)
+
+#define info(format, args...) ((void)0)
+
+#else
+void info_P(PGM_P format, ...)
+{
+#ifdef NO_INFO
+
+#else
+    strlcpy_P((char *) buffer_info, format, FORMAT_BUFFER_LEN);
+    va_list args;
+    va_start(args, format);
+    vprintf((char *) buffer_info, args);
+    va_end(args);
+#endif
+}
+#endif

avr/usbload/info.h

@@ -26,16 +26,31 @@
 #include <stdlib.h>
 #include <stdint.h>
 #include <stdarg.h>
-
+#include <avr/pgmspace.h>
 
 #if defined(NO_INFO) && defined(__GNUC__)
-/* gcc's cpp has extensions; it allows for macros with a variable number of
+/*
-   arguments. We use this extension here to preprocess pmesg away. */
+ * gcc's cpp has extensions; it allows for macros with a variable number of arguments. We use this extension here to preprocess pmesg away. 
+ */
 #define info(format, args...) ((void)0)
 #else
 void info(char *format, ...);
-/* print a message, if it is considered significant enough.
+/*
-      Adapted from [K&R2], p. 174 */
+ * print a message, if it is considered significant enough. Adapted from [K&R2], p. 174 
+ */
+#endif
+
+
+#if defined(NO_INFO) && defined(__GNUC__)
+/*
+ * gcc's cpp has extensions; it allows for macros with a variable number of arguments. We use this extension here to preprocess pmesg away. 
+ */
+#define info_P(format, args...) ((void)0)
+#else
+void info_P(PGM_P format, ...);
+/*
+ * print a message, if it is considered significant enough. Adapted from [K&R2], p. 174 
+ */
 #endif
 
 

avr/usbload/irq.c

@@ -0,0 +1,75 @@
+/*
+ * =====================================================================================
+ *
+ * ________        .__        __    ________               ____  ________
+ * \_____  \  __ __|__| ____ |  | __\______ \   _______  _/_   |/  _____/
+ *  /  / \  \|  |  \  |/ ___\|  |/ / |    |  \_/ __ \  \/ /|   /   __  \
+ * /   \_/.  \  |  /  \  \___|    <  |    `   \  ___/\   / |   \  |__\  \
+ * \_____\ \_/____/|__|\___  >__|_ \/_______  /\___  >\_/  |___|\_____  /
+ *        \__>             \/     \/        \/     \/                 \/
+ *
+ *                                  www.optixx.org
+ *
+ *
+ *        Version:  1.0
+ *        Created:  07/21/2009 03:32:16 PM
+ *         Author:  david@optixx.org
+ *
+ * =====================================================================================
+ */
+
+
+
+
+#include <stdint.h>
+#include <stdio.h>
+#include <avr/interrupt.h>      /* for sei() */
+#include <avr/wdt.h>
+
+
+#include "usbdrv.h"
+#include "oddebug.h"            /* This is also an example for using debug macros */
+#include "debug.h"
+#include "info.h"
+#include "sram.h"
+#include "system.h"
+
+extern system_t my_system;
+
+void (*jump_to_app) (void) = 0x0000;
+
+void irq_init()
+{
+    cli();
+    PCMSK3 |= (1 << PCINT27);
+    PCICR |= (1 << PCIE3);
+    sei();
+    my_system.reset_irq = RESET_IRQ_ON;
+}
+
+void irq_stop()
+{
+    cli();
+    PCMSK3 &= ~(1 << PCINT27);
+    sei();
+    my_system.reset_irq = RESET_IRQ_OFF;
+}
+
+void leave_application(void)
+{
+    cli();
+    usbDeviceDisconnect();
+    my_system.avr_reset_count++;
+    wdt_enable(WDTO_15MS);
+    while (1);
+
+}
+
+ISR(PCINT3_vect)
+{
+    if (snes_reset_test()) {
+        info_P(PSTR("Catch SNES reset button\n"));
+        info_P(PSTR("Set watchdog...\n"));
+        leave_application();
+    }
+}

avr/usbload/irq.h

@@ -0,0 +1,28 @@
+/*
+ * =====================================================================================
+ *
+ * ________        .__        __    ________               ____  ________
+ * \_____  \  __ __|__| ____ |  | __\______ \   _______  _/_   |/  _____/
+ *  /  / \  \|  |  \  |/ ___\|  |/ / |    |  \_/ __ \  \/ /|   /   __  \
+ * /   \_/.  \  |  /  \  \___|    <  |    `   \  ___/\   / |   \  |__\  \
+ * \_____\ \_/____/|__|\___  >__|_ \/_______  /\___  >\_/  |___|\_____  /
+ *        \__>             \/     \/        \/     \/                 \/
+ *
+ *                                  www.optixx.org
+ *
+ *
+ *        Version:  1.0
+ *        Created:  07/21/2009 03:32:16 PM
+ *         Author:  david@optixx.org
+ *
+ * =====================================================================================
+ */
+
+
+#ifndef __IRQ_H__
+#define __IRQ_H__
+
+void irq_init();
+void irq_stop();
+void leave_application(void);
+#endif

avr/usbload/loader.c

@@ -1,11 +1,11 @@
 /*
-File: main.smc 
+File: %s
-Time: Thu, 06 Aug 2009 20:01:38
+Time: %s
 */
 #include <avr/pgmspace.h>
 #include <loader.h>
 
-const char _rom[ROM_BUFFER_SIZE] PROGMEM = {
+const char _rom01[ROM_BUFFER_SIZE01] PROGMEM = {
 0x00,0x90,0x04,0x08,0xc2,0x30,0xa9,0x00,0x00,0x20,0x12,0x00,0x20,0xd2,0x08,0x28,0x60,
 0x08,0xc2,0x31,0x29,0xff,0x00,0x0a,0x0a,0xaa,0xbf,0xe5,0x57,0x7f,0x48,0xbf,0xe3,
 0x57,0x7f,0x48,0xa6,0x8c,0xe2,0x20,0xa9,0x01,0x9f,0x93,0x2d,0x7e,0xa9,0x7f,0x9f,
@@ -1950,4 +1950,6 @@ const char _rom[ROM_BUFFER_SIZE] PROGMEM = {
 0x01,0xdc,0xbc,0x23,0x43,0xff,0x90,0x04,0xa0,0xff,0xa0,0xff,0xa0,0xff,0xb6,0xff,
 0x00,0x00,0xb7,0xff,0x90,0x05,0xa0,0xff,0x00,0x00,0xa0,0xff,0xa0,0xff,0xa1,0xff,
 0xa0,0xff
-};
+    };
+PGM_VOID_P _rom[ROM_BUFFER_CNT]= {&_rom01};
+const int _rom_size[ROM_BUFFER_CNT] = {31091};

avr/usbload/loader.h

@@ -1,9 +1,15 @@
-
+/*
+File: qd16boot_ver01.smc
+Time: Sat, 20 Aug 2016 18:12:14
+*/
 #ifndef __FIFO_H__
 #define __FIFO_H__
 
-#define ROM_BUFFER_SIZE  31091
+#define LOADER_NAME "qd16boot_ver01.smc"
-#define ROM_HUFFMAN_SIZE 0
+#define LOADER_COMPRESS "RLE"
 #define ROM_RLE_SIZE     31091
+#define ROM_BUFFER_CNT   1
+
+#define ROM_BUFFER_SIZE01  31091
 
 #endif

avr/usbload/main.c

@@ -19,13 +19,12 @@
  */
 
 
-
-#include <avr/io.h>
 #include <avr/interrupt.h>
 #include <util/delay.h>
 #include <stdlib.h>
 #include <avr/pgmspace.h>
 #include <avr/eeprom.h>
+#include <string.h>
 
 #include "usbdrv.h"
 #include "oddebug.h"
@@ -44,35 +43,20 @@
 #include "loader.h"
 #include "command.h"
 #include "shared_memory.h"
+#include "irq.h"
+#include "pwm.h"
 #include "testing.h"
+#include "shell.h"
+#include "system.h"
 
-
+#ifndef NO_DEBUG
-
-extern const char _rom[] PROGMEM;
 extern FILE uart_stdout;
+#endif
+extern system_t my_system;
 
 uint8_t debug_level = (DEBUG | DEBUG_USB | DEBUG_CRC);
 
-uint8_t read_buffer[TRANSFER_BUFFER_SIZE];
+usb_transaction_t usb_trans;
-uint32_t req_addr = 0;
-uint32_t req_addr_end = 0;
-uint32_t req_size;
-uint8_t req_bank;
-uint32_t req_bank_size;
-uint16_t req_bank_cnt;
-uint8_t req_percent;
-uint8_t req_percent_last;
-uint8_t req_state = REQ_STATUS_IDLE;
-uint8_t rx_remaining = 0;
-uint8_t tx_remaining = 0;
-uint16_t sync_errors = 0;
-uint8_t tx_buffer[32];
-uint8_t data_buffer[4];
-uint32_t addr;
-uint16_t crc = 0;
-
-
-
 
 usbMsgLen_t usbFunctionSetup(uchar data[8])
 {
@@ -82,53 +66,68 @@ usbMsgLen_t usbFunctionSetup(uchar data[8])
 
     if (rq->bRequest == USB_BULK_UPLOAD_INIT) {
 
-        req_bank = 0;
+        usb_trans.req_bank = 0;
-        rx_remaining = 0;
+        usb_trans.rx_remaining = 0;
-        debug(DEBUG_USB, "USB_BULK_UPLOAD_INIT: %i %i\n", rq->wValue.word,
+        debug_P(DEBUG_USB, PSTR("USB_BULK_UPLOAD_INIT: %i %i\n"),
-              rq->wIndex.word);
+                rq->wValue.word, rq->wIndex.word);
-        req_bank_size = (uint32_t) (1L << rq->wValue.word);
+        usb_trans.req_bank_size = (uint32_t) (1L << rq->wValue.word);
-        req_bank_cnt = rq->wIndex.word;
+        usb_trans.req_bank_cnt = rq->wIndex.word;
-        req_addr_end = (uint32_t) req_bank_size *req_bank_cnt;
+        usb_trans.req_addr_end =
-        req_percent = 0;
+            (uint32_t) usb_trans.req_bank_size * usb_trans.req_bank_cnt;
-        req_percent_last = 0;
+        usb_trans.req_percent = 0;
-        sync_errors = 0;
+        usb_trans.req_percent_last = 0;
-        debug(DEBUG_USB,
+        usb_trans.sync_errors = 0;
-              "USB_BULK_UPLOAD_INIT: bank_size=0x%08lx bank_cnt=0x%x end_addr=0x%08lx\n",
+        debug_P(DEBUG_USB,
-              req_bank_size, req_bank_cnt, req_addr_end);
+                PSTR
+                ("USB_BULK_UPLOAD_INIT: bank_size=0x%08lx bank_cnt=0x%x end_addr=0x%08lx\n"),
+                usb_trans.req_bank_size, usb_trans.req_bank_cnt,
+                usb_trans.req_addr_end);
 
-        shared_memory_write(SHARED_MEM_TX_CMD_BANK_COUNT, req_bank_cnt);
+        shared_memory_write(SHARED_MEM_TX_CMD_UPLOAD_START, 0);
-        if (req_addr == 0x000000) {
+        shared_memory_write(SHARED_MEM_TX_CMD_BANK_COUNT,
+                            usb_trans.req_bank_cnt);
+#if DO_TIMER
+        if (usb_trans.req_addr == 0x000000) {
+#ifndef NO_DEBUG
             timer_start();
+#endif
         }
+#endif
         /*
          * -------------------------------------------------------------------------
          */
     } else if (rq->bRequest == USB_BULK_UPLOAD_ADDR) {
 
-        req_state = REQ_STATUS_BULK_UPLOAD;
+        usb_trans.req_state = REQ_STATUS_BULK_UPLOAD;
-        req_addr = rq->wValue.word;
+        usb_trans.req_addr = rq->wValue.word;
-        req_addr = req_addr << 16;
+        usb_trans.req_addr = usb_trans.req_addr << 16;
-        req_addr = req_addr | rq->wIndex.word;
+        usb_trans.req_addr = usb_trans.req_addr | rq->wIndex.word;
-        rx_remaining = rq->wLength.word;
+        usb_trans.rx_remaining = rq->wLength.word;
 
 
-        if (req_addr && req_addr % req_bank_size == 0) {
+
+        if (usb_trans.req_addr
+            && usb_trans.req_addr % usb_trans.req_bank_size == 0) {
+#if DO_TIMER
+#ifndef NO_DEBUG
 #ifdef FLT_DEBUG
-            debug(DEBUG_USB,
+            debug_P(DEBUG_USB,
-                  "USB_BULK_UPLOAD_ADDR: req_bank=0x%02x addr=0x%08lx time=%.4f\n",
+                    PSTR
-                  req_bank, req_addr, timer_stop());
+                    ("USB_BULK_UPLOAD_ADDR: req_bank=0x%02x addr=0x%08lx time=%.4f\n"),
+                    usb_trans.req_bank, usb_trans.req_addr, timer_stop());
 #else
-            debug(DEBUG_USB,
+            debug_P(DEBUG_USB,
-                  "USB_BULK_UPLOAD_ADDR: req_bank=0x%02x addr=0x%08lx time=%i\n",
+                    PSTR
-                  req_bank, req_addr, timer_stop_int());
+                    ("USB_BULK_UPLOAD_ADDR: req_bank=0x%02x addr=0x%08lx time=%i\n"),
+                    usb_trans.req_bank, usb_trans.req_addr, timer_stop_int());
 #endif
-            req_bank++;
-            shared_memory_write(SHARED_MEM_TX_CMD_UPLOAD_PROGESS, req_bank);
-            sram_bulk_write_start(req_addr);
             timer_start();
+#endif
+#endif
+            usb_trans.req_bank++;
 
         } else {
-            sram_bulk_write_start(req_addr);
+            sram_bulk_write_start(usb_trans.req_addr);
         }
         ret_len = USB_MAX_TRANS;
 
@@ -136,282 +135,195 @@ usbMsgLen_t usbFunctionSetup(uchar data[8])
          * -------------------------------------------------------------------------
          */
     } else if (rq->bRequest == USB_BULK_UPLOAD_NEXT) {
+        usb_trans.req_state = REQ_STATUS_BULK_UPLOAD;
+        usb_trans.req_addr = rq->wValue.word;
+        usb_trans.req_addr = usb_trans.req_addr << 16;
+        usb_trans.req_addr = usb_trans.req_addr | rq->wIndex.word;
+        usb_trans.rx_remaining = rq->wLength.word;
 
-        req_state = REQ_STATUS_BULK_UPLOAD;
+#if DO_SHM
-        req_addr = rq->wValue.word;
+        usb_trans.req_percent =
-        req_addr = req_addr << 16;
+            (uint32_t) (100 * usb_trans.req_addr) / usb_trans.req_addr_end;
-        req_addr = req_addr | rq->wIndex.word;
+        if (usb_trans.req_percent != usb_trans.req_percent_last) {
-        rx_remaining = rq->wLength.word;
+            shared_memory_write(SHARED_MEM_TX_CMD_UPLOAD_PROGESS,
-
+                                usb_trans.req_percent);
-        req_percent = (uint32_t)( 100 * req_addr )  / req_addr_end;
-        if (req_percent!=req_percent_last){
-            debug(DEBUG_USB,
-                "USB_BULK_UPLOAD_ADDR: precent=%i\n",  req_percent);
-            shared_memory_write(SHARED_MEM_TX_CMD_UPLOAD_PROGESS, req_percent);
-            sram_bulk_write_start(req_addr);
         }
-        req_percent_last = req_percent;
+        usb_trans.req_percent_last = usb_trans.req_percent;
-
+        shared_memory_scratchpad_region_save_helper(usb_trans.req_addr);
-#if 0
-        if (req_addr && (req_addr % 0x1000) == 0) {
-            debug(DEBUG_USB,
-                  "USB_BULK_UPLOAD_NEXT: bank=0x%02x addr=0x%08lx crc=%04x\n",
-                  req_bank, req_addr, crc_check_bulk_memory(req_addr - 0x1000,
-                                                            req_addr,
-                                                            req_bank_size));
-
-        }
-        sram_bulk_write_start(req_addr);
 #endif
-        if (req_addr && (req_addr % req_bank_size) == 0) {
+        if (usb_trans.req_addr
+            && (usb_trans.req_addr % usb_trans.req_bank_size) == 0) {
+#if DO_TIMER
+#ifndef NO_DEBUG
 #ifdef FLT_DEBUG
-            debug(DEBUG_USB,
+            debug_P(DEBUG_USB,
-                  "USB_BULK_UPLOAD_NEXT: req_bank=0x%02x addr=0x%08lx time=%.4f\n",
+                    PSTR
-                  req_bank, req_addr, timer_stop());
+                    ("USB_BULK_UPLOAD_NEXT: req_bank=0x%02x addr=0x%08lx time=%.4f\n"),
+                    usb_trans.req_bank, usb_trans.req_addr, timer_stop());
 #else
-            debug(DEBUG_USB,
+            debug_P(DEBUG_USB,
-                  "USB_BULK_UPLOAD_NEXT: req_bank=0x%02x addr=0x%08lx time=%i\n",
+                    PSTR
-                  req_bank, req_addr, timer_stop_int());
+                    ("USB_BULK_UPLOAD_NEXT: req_bank=0x%02x addr=0x%08lx time=%i\n"),
+                    usb_trans.req_bank, usb_trans.req_addr, timer_stop_int());
 #endif
-            req_bank++;
             timer_start();
-            shared_memory_write(SHARED_MEM_TX_CMD_BANK_CURRENT, req_bank);
+#endif
-            sram_bulk_write_start(req_addr);
+#endif
-
+            usb_trans.req_bank++;
+#if DO_SHM
+            shared_memory_write(SHARED_MEM_TX_CMD_BANK_CURRENT,
+                                usb_trans.req_bank);
+#endif
         }
         ret_len = USB_MAX_TRANS;
         /*
          * -------------------------------------------------------------------------
          */
     } else if (rq->bRequest == USB_BULK_UPLOAD_END) {
-        if (req_state != REQ_STATUS_BULK_UPLOAD) {
+        debug_P(DEBUG_USB, PSTR("USB_BULK_UPLOAD_END:\n"));
-            debug(DEBUG_USB,
+        usb_trans.req_state = REQ_STATUS_IDLE;
-                  "USB_BULK_UPLOAD_END: ERROR state is not REQ_STATUS_BULK_UPLOAD\n");
-            return 0;
-        }
-        debug(DEBUG_USB, "USB_BULK_UPLOAD_END:\n");
-        req_state = REQ_STATUS_IDLE;
         sram_bulk_write_end();
+#if DO_SHM
         shared_memory_write(SHARED_MEM_TX_CMD_UPLOAD_END, 0);
+#endif
         ret_len = 0;
 
         /*
          * -------------------------------------------------------------------------
          */
     } else if (rq->bRequest == USB_CRC) {
-        req_addr = rq->wValue.word;
+        usb_trans.req_addr = rq->wValue.word;
-        req_addr = req_addr << 16;
+        usb_trans.req_addr = usb_trans.req_addr << 16;
-        req_addr = req_addr | rq->wIndex.word;
+        usb_trans.req_addr = usb_trans.req_addr | rq->wIndex.word;
-        debug(DEBUG_USB, "USB_CRC: addr=0x%08lx \n", req_addr);
+        debug_P(DEBUG_USB, PSTR("USB_CRC: addr=0x%08lx \n"),
-        crc_check_bulk_memory(0x000000, req_addr, req_bank_size);
+                usb_trans.req_addr);
+#if DO_CRC_CHECK
+        crc_check_bulk_memory(0x000000, usb_trans.req_addr,
+                              usb_trans.req_bank_size);
+#endif
         ret_len = 0;
         /*
          * -------------------------------------------------------------------------
          */
     } else if (rq->bRequest == USB_MODE_SNES) {
-        req_state = REQ_STATUS_SNES;
+        usb_trans.req_state = REQ_STATUS_SNES;
-        debug(DEBUG_USB, "USB_MODE_SNES:\n");
+        debug_P(DEBUG_USB, PSTR("USB_MODE_SNES:\n"));
         ret_len = 0;
+
         /*
          * -------------------------------------------------------------------------
          */
     } else if (rq->bRequest == USB_MODE_AVR) {
-        req_state = REQ_STATUS_AVR;
+        usb_trans.req_state = REQ_STATUS_AVR;
-        debug(DEBUG_USB, "USB_MODE_AVR:\n");
+        debug_P(DEBUG_USB, PSTR("USB_MODE_AVR:\n"));
         ret_len = 0;
         /*
          * -------------------------------------------------------------------------
          */
     } else if (rq->bRequest == USB_AVR_RESET) {
-        debug(DEBUG_USB, "USB_AVR_RESET:\n");
+        debug_P(DEBUG_USB, PSTR("USB_AVR_RESET:\n"));
         soft_reset();
         ret_len = 0;
         /*
          * -------------------------------------------------------------------------
          */
-
+    } else if (rq->bRequest == USB_SET_LAODER) {
-    } else if (rq->bRequest == USB_CRC_ADDR) {
+        debug_P(DEBUG_USB, PSTR("USB_SET_LAODER:\n"));
-        req_state = REQ_STATUS_CRC;
+        usb_trans.loader_enabled = rq->wValue.word;
-        req_addr = rq->wValue.word;
+        ret_len = 0;
-        req_addr = req_addr << 16;
-        req_addr = req_addr | rq->wIndex.word;
-        debug(DEBUG_USB, "USB_CRC_ADDR: addr=0x%lx size=%i\n", req_addr,
-              rq->wLength.word);
-        req_size = rq->wLength.word;
-        req_size = req_size << 2;
-        tx_remaining = 2;
-        debug(DEBUG_USB, "USB_CRC_ADDR: addr=0x%lx size=%li\n", req_addr,
-              req_size);
-
-        crc = crc_check_memory_range(req_addr, req_size, read_buffer);
-        tx_buffer[0] = crc & 0xff;
-        tx_buffer[1] = (crc >> 8) & 0xff;
-        ret_len = 2;
-        req_state = REQ_STATUS_IDLE;
     }
-
+    usbMsgPtr = usb_trans.rx_buffer;
-    usbMsgPtr = data_buffer;
+    return ret_len;
-    return ret_len;             /* default for not implemented requests: return no data back to host */
 }
 
-
 /*
  * ------------------------------------------------------------------------- 
  */
 
 
-void usb_connect()
+void globals_init()
 {
-    uint8_t i = 0;
+    memset(&usb_trans, 0, sizeof(usb_transaction_t));
-    info("USB init\n");
+
-    usbDeviceDisconnect();      /* enforce re-enumeration, do this while */
+    usb_trans.req_addr = 0;
-    cli();
+    usb_trans.req_addr_end = 0;
-    info("USB disconnect\n");
+    usb_trans.req_state = REQ_STATUS_IDLE;
-    i = 10;
+    usb_trans.rx_remaining = 0;
-    while (--i) {               /* fake USB disconnect for > 250 ms */
+    usb_trans.tx_remaining = 0;
-        led_on();
+    usb_trans.sync_errors = 0;
-        _delay_ms(35);
+    usb_trans.loader_enabled = 1;
-        led_off();
-        _delay_ms(65);
-    }
-    led_on();
-    usbDeviceConnect();
-    info("USB connect\n");
 }
 
-
-void boot_startup_rom()
-{
-
-
-    info("Activate AVR bus\n");
-    avr_bus_active();
-
-    info("IRQ off\n");
-    snes_irq_lo();
-    snes_irq_off();
-
-    snes_lorom();
-    info("Set Snes lowrom \n");
-
-    rle_decode(&_rom, ROM_BUFFER_SIZE, 0x000000);
-    dump_memory(0x10000 - 0x100, 0x10000);
-
-    snes_reset_hi();
-    snes_reset_off();
-    snes_irq_lo();
-    snes_irq_off();
-    info("IRQ off\n");
-    snes_hirom();
-    snes_wr_disable();
-    info("Disable snes WR\n");
-    snes_bus_active();
-    info("Activate Snes bus\n");
-    _delay_ms(100);
-    info("Reset Snes\n");
-    send_reset();
-    _delay_ms(100);
-#if 0
-    uint8_t i = 0;
-    i = 20;
-    info("Wait");
-    while (--i) {
-        _delay_ms(500);
-        info(".");
-    }
-    info("\n");
-#endif
-}
-
-
 int main(void)
 {
 
+#ifndef NO_DEBUG
     uart_init();
     stdout = &uart_stdout;
-
+    banner();
-    info("Sytem start\n");
-    system_init();
-
-#if 0
-    test_read_write();
-    test_bulk_read_write();
-    test_crc();
-    while (1);
 #endif
-
+    shared_memory_init();
-    info("Boot startup rom\n");
+    system_init();
-    boot_startup_rom();
+    sram_init();
-
+    pwm_init();
+    irq_init();
+    boot_startup_rom(50);
+    globals_init();
+    pwm_stop();
     usbInit();
     usb_connect();
-
+    sei();
     while (1) {
-        avr_bus_active();
+        system_set_bus_avr();
-        info("Activate AVR bus\n");
+        system_set_wr_disable();
-        info("IRQ off\n");
+        while (usb_trans.req_state != REQ_STATUS_SNES) {
-        snes_irq_lo();
-        snes_irq_off();
-        info("Set Snes lowrom\n");
-        snes_lorom();
-        info("Disable snes WR\n");
-        snes_wr_disable();
-        sei();
-        info("USB poll\n");
-        while (req_state != REQ_STATUS_SNES) {
             usbPoll();
+#if DO_SHELL
+#ifndef NO_DEBUG
+            shell_run();
+#endif
+#endif
         }
+
+#if DO_SHM
         shared_memory_write(SHARED_MEM_TX_CMD_TERMINATE, 0);
-        info("USB poll done\n");
-        set_rom_mode();
-        snes_wr_disable();
-        info("Disable snes WR\n");
-        snes_bus_active();
-        info("Activate Snes bus\n");
-        _delay_ms(100);
-        info("Reset Snes\n");
-        send_reset();
-
-        info("Poll\n");
-        while (req_state != REQ_STATUS_AVR) {
-            usbPoll();
-
-#ifdef DO_IRQ
-            uint8_t i;
-            uint16_t irq_count = 0;
-            i = 10;
-            while (--i) {
-                _delay_ms(100);
-            }
-            info("Send IRQ %i\n", ++irq_count);
-            send_irq();
 #endif
 
-#ifdef DO_BUS_STEALING
+#if DO_SHM_SCRATCHPAD
-            avr_bus_active();
+        shared_memory_scratchpad_region_tx_restore();
-            sram_bulk_read_start(0x003000);
+        shared_memory_scratchpad_region_rx_restore();
-            c = sram_bulk_read();
+#endif
-            i = 5;
-            while (--i) {
-                _delay_ms(500);
-                info("Wait to switch to snes mode %i\n", i);
-            }
 
-            if (req_bank_size == 0x8000) {
+#if DO_CRC_CHECK
-                snes_lorom();
+        info_P(PSTR("-->CRC Check\n"));
-                info("Set Snes lowrom \n");
+        crc_check_bulk_memory(0x000000,
-            } else {
+                              usb_trans.req_bank_size * usb_trans.req_bank_cnt,
-                snes_hirom();
+                              usb_trans.req_bank_size);
-                info("Set Snes hirom \n");
+#endif
-            }
+
-            snes_wr_disable();
+        system_set_rom_mode(&usb_trans);
-            info("Disable snes WR\n");
+        system_set_wr_disable();
-            snes_bus_active();
+        system_set_bus_snes();
-            info("Activate Snes bus\n");
+        system_send_snes_reset();
-            info("Read 0x3000=%c\n", c);
+        irq_stop();
+        while ((usb_trans.req_state != REQ_STATUS_AVR)) {
+            usbPoll();
+#if DO_SHELL
+#ifndef NO_DEBUG
+            shell_run();
+#endif
 #endif
         }
+        info_P(PSTR("-->Switch TO AVR\n"));
+        shared_memory_init();
+        irq_init();
+        if (usb_trans.loader_enabled) {
+            boot_startup_rom(50);
+        } else {
+            system_set_bus_avr();
+            system_send_snes_reset();
+        }
+        globals_init();
     }
-
     return 0;
 }

avr/usbload/memmory.txt

@@ -0,0 +1,30 @@
+
+Loader Version 1
+
+DEBUG:
+Bootloader:     4096
+CODE:           24984 
+RAM:            742
+LOADER:         31091
+
+NO_DEBUG:
+Bootloader:     4096
+CODE:           7532 
+RAM:            344
+LOADER:         31091
+ 
+
+Loader Version 2
+
+DEBUG:
+Bootloader:     4096
+CODE:           24984 
+RAM:            742
+LOADER:         58046
+
+NO_DEBUG:
+Bootloader:     4096
+CODE:           7532 
+RAM:            344
+LOADER:         58046
+

avr/usbload/pwm.c

@@ -0,0 +1,113 @@
+/*
+ * =====================================================================================
+ *
+ * ________        .__        __    ________               ____  ________
+ * \_____  \  __ __|__| ____ |  | __\______ \   _______  _/_   |/  _____/
+ *  /  / \  \|  |  \  |/ ___\|  |/ / |    |  \_/ __ \  \/ /|   /   __  \
+ * /   \_/.  \  |  /  \  \___|    <  |    `   \  ___/\   / |   \  |__\  \
+ * \_____\ \_/____/|__|\___  >__|_ \/_______  /\___  >\_/  |___|\_____  /
+ *        \__>             \/     \/        \/     \/                 \/
+ *
+ *                                  www.optixx.org
+ *
+ *
+ *        Version:  1.0
+ *        Created:  07/21/2009 03:32:16 PM
+ *         Author:  david@optixx.org
+ *
+ * =====================================================================================
+ */
+#include <stdint.h>
+#include <string.h>
+#include <avr/io.h>
+#include <avr/interrupt.h>
+
+#include "pwm.h"
+#include "debug.h"
+#include "info.h"
+#include "sram.h"
+
+
+#define PWM_SINE_MAX 64
+#define PWM_OVERFLOW_MAX 1024
+
+uint8_t pwm_sine_table[] = {
+    0x7f, 0x8b, 0x97, 0xa4, 0xaf, 0xbb, 0xc5, 0xcf, 0xd9, 0xe1, 0xe8, 0xef,
+        0xf4, 0xf8, 0xfb, 0xfd,
+    0xfd, 0xfd, 0xfb, 0xf8, 0xf3, 0xee, 0xe7, 0xe0, 0xd7, 0xce, 0xc4, 0xb9,
+        0xae, 0xa2, 0x96, 0x89,
+    0x7e, 0x71, 0x65, 0x59, 0x4d, 0x42, 0x37, 0x2d, 0x24, 0x1c, 0x15, 0x0f,
+        0x09, 0x05, 0x03, 0x01,
+    0x01, 0x01, 0x03, 0x07, 0x0b, 0x11, 0x17, 0x1f, 0x28, 0x31, 0x3b, 0x46,
+        0x52, 0x5e, 0x6a, 0x76
+};
+
+volatile uint8_t pwm_setting;
+volatile uint16_t pwm_overflow;
+volatile uint8_t pwm_idx;
+volatile uint16_t pwm_overflow_max;
+
+ISR(TIMER2_COMPA_vect)
+{
+    static uint8_t pwm_cnt = 0;
+    OCR2A += (uint16_t) T_PWM;
+
+    if (pwm_setting > pwm_cnt)
+        led_pwm_on();
+    else
+        led_pwm_off();
+
+    if (pwm_cnt == (uint8_t) (PWM_STEPS - 1))
+        pwm_cnt = 0;
+    else
+        pwm_cnt++;
+    if (pwm_overflow_max == pwm_overflow++) {
+        pwm_setting = pwm_sine_table[pwm_idx++];
+        pwm_overflow = 0;
+        if (PWM_SINE_MAX == pwm_idx)
+            pwm_idx = 0;
+    }
+}
+
+void pwm_speed(uint16_t val)
+{
+    pwm_overflow_max = val;
+}
+
+void pwm_speed_slow(uint16_t val)
+{
+    pwm_overflow_max = PWM_OVERFLOW_MAX * 2;
+}
+
+void pwm_speed_fast(uint16_t val)
+{
+    pwm_overflow_max = PWM_OVERFLOW_MAX / 2;
+}
+
+void pwm_speed_normal(uint16_t val)
+{
+    pwm_overflow_max = PWM_OVERFLOW_MAX;
+}
+
+
+void pwm_set(uint8_t val)
+{
+    pwm_setting = val;
+}
+
+void pwm_stop(void)
+{
+    while (pwm_setting != 0xfd);
+    TIMSK2 = 0;
+}
+
+void pwm_init(void)
+{
+    pwm_overflow_max = PWM_OVERFLOW_MAX;
+    pwm_setting = 0x7f;
+    pwm_overflow = 0;
+    // cli();
+    TCCR2B = 1;
+    TIMSK2 |= (1 << OCIE2A);
+    sei();
+}

avr/usbload/pwm.h

@@ -0,0 +1,37 @@
+/*
+ * =====================================================================================
+ *
+ * ________        .__        __    ________               ____  ________
+ * \_____  \  __ __|__| ____ |  | __\______ \   _______  _/_   |/  _____/
+ *  /  / \  \|  |  \  |/ ___\|  |/ / |    |  \_/ __ \  \/ /|   /   __  \
+ * /   \_/.  \  |  /  \  \___|    <  |    `   \  ___/\   / |   \  |__\  \
+ * \_____\ \_/____/|__|\___  >__|_ \/_______  /\___  >\_/  |___|\_____  /
+ *        \__>             \/     \/        \/     \/                 \/
+ *
+ *                                  www.optixx.org
+ *
+ *
+ *        Version:  1.0
+ *        Created:  07/21/2009 03:32:16 PM
+ *         Author:  david@optixx.org
+ *
+ * =====================================================================================
+ */
+
+#ifndef __PWM_H__
+#define __PWM_H__
+
+#define F_PWM 100               // PWM-Frequenz in Hz
+#define PWM_STEPS 256           // PWM-Schritte pro Zyklus(1..256)
+
+#define T_PWM (F_CPU/(F_PWM*PWM_STEPS)) // Systemtakte pro PWM-Takt
+
+#if (T_PWM<(93+5))
+#error T_PWM zu klein, F_CPU muss vergrösst werden oder F_PWM oder PWM_STEPS verkleinert werden
+#endif
+
+void pwm_init(void);
+void pwm_stop(void);
+
+
+#endif

avr/usbload/requests.h

@@ -38,5 +38,23 @@
 #define USB_MODE_SNES           10
 #define USB_MODE_AVR            11
 #define USB_AVR_RESET           12
+#define USB_SET_LAODER          13
 
-#endif /* __REQUESTS_H_INCLUDED__ */
+typedef struct usb_transaction_t {
+    uint32_t req_addr;
+    uint32_t req_addr_end;
+    uint8_t req_bank;
+    uint32_t req_bank_size;
+    uint16_t req_bank_cnt;
+    uint8_t req_percent;
+    uint8_t req_percent_last;
+    uint8_t req_state;
+    uint8_t rx_remaining;
+    uint8_t tx_remaining;
+    uint16_t sync_errors;
+    uint8_t tx_buffer[32];
+    uint8_t rx_buffer[8];
+    uint8_t loader_enabled;
+} usb_transaction_t;
+
+#endif                          /* __REQUESTS_H_INCLUDED__ */

avr/usbload/ringbuffer.h

@@ -0,0 +1,42 @@
+#ifndef _ringbuffer_h
+#define _ringbuffer_h
+
+int __mod(int a, int b)
+{
+    int r = a % b;
+    return r < 0 ? r + b : r;
+}
+
+#define ring_buffer_typedef(T, NAME) \
+  typedef struct { \
+    int size; \
+    int start; \
+    int end; \
+    T* elems; \
+  } NAME
+
+#define buffer_init(BUF, S, T) \
+  BUF.size = S+1; \
+  BUF.start = 0; \
+  BUF.end = 0; \
+  BUF.elems = (T*)calloc(BUF.size, sizeof(T))
+
+
+#define buffer_destroy(BUF) free(BUF->elems)
+#define nex_start_index(BUF) ((BUF->start + 1) % BUF->size)
+#define is_buffer_empty(BUF) (BUF->end == BUF->start)
+#define buffer_get(BUF, INDEX) (BUF->elems[__mod(BUF->end - INDEX, BUF->size)])
+
+#define bufferWrite(BUF, ELEM) \
+  BUF->elems[BUF->end] = ELEM; \
+  BUF->end = (BUF->end + 1) % BUF->size; \
+  if (is_buffer_empty(BUF)) { \
+    BUF->start = nex_start_index(BUF); \
+  }
+
+#define bufferRead(BUF, ELEM) \
+    ELEM = BUF->elems[BUF->start]; \
+    BUF->start = nex_start_index(BUF);
+
+#endif
+

avr/usbload/rle.c

@@ -32,14 +32,12 @@
 
 #define RUNCHAR 0x90
 
-uint8_t rle_decode(PGM_VOID_P in_addr, int32_t in_len, uint32_t out_addr)
+uint32_t rle_decode(PGM_VOID_P in_addr, int32_t in_len, uint32_t out_addr)
 {
     uint8_t in_byte, in_repeat, last_byte;
-    uint32_t out_len, out_len_left;
+    info_P(PSTR("RLE decode len=%li addr=0x%08lx\n"), in_len, out_addr);
-    info("RLE decode len=%li addr=0x%08lx\n", in_len, out_addr);
     last_byte = 0;
 
-    out_len_left = out_len;
     sram_bulk_write_start(out_addr);
 #define INBYTE(b) \
 	do { \
@@ -63,7 +61,7 @@ uint8_t rle_decode(PGM_VOID_P in_addr, int32_t in_len, uint32_t out_addr)
     if (in_byte == RUNCHAR) {
         INBYTE(in_repeat);
         if (in_repeat != 0) {
-            info("Orphaned RLE code at start\n");
+            info_P(PSTR("Orphaned RLE code at start\n"));
             return 1;
         }
         OUTBYTE(RUNCHAR);
@@ -74,7 +72,7 @@ uint8_t rle_decode(PGM_VOID_P in_addr, int32_t in_len, uint32_t out_addr)
     while (in_len > 0) {
         INBYTE(in_byte);
         if (in_len % 1024 == 0)
-            info(".");
+            info_P(PSTR("."));
         if (in_byte == RUNCHAR) {
             INBYTE(in_repeat);
             if (in_repeat == 0) {
@@ -99,5 +97,6 @@ uint8_t rle_decode(PGM_VOID_P in_addr, int32_t in_len, uint32_t out_addr)
         last_byte = in_byte;
     }
     sram_bulk_write_end();
-    return 0;
+    info_P(PSTR("\nDone addr=0x%08lx\n"), out_addr);
+    return out_addr;
 }

avr/usbload/rle.h

@@ -23,6 +23,6 @@
 
 #include <avr/pgmspace.h>
 
-uint8_t rle_decode(PGM_VOID_P in_addr, uint32_t in_len, uint32_t out_addr);
+uint32_t rle_decode(PGM_VOID_P in_addr, uint32_t in_len, uint32_t out_addr);
 
 #endif

avr/usbload/shared_memory.c

@@ -29,7 +29,10 @@
 #include "config.h"
 #include "sram.h"
 #include "debug.h"
+#include "dump.h"
 #include "info.h"
+#include "crc.h"
+
 
 uint8_t irq_addr_lo;
 uint8_t irq_addr_hi;
@@ -38,6 +41,207 @@ uint8_t scratchpad_state;
 uint8_t scratchpad_cmd;
 uint8_t scratchpad_payload;
 
+uint8_t scratchpad_region_rx[SHARED_MEM_RX_LOC_SIZE];
+uint8_t scratchpad_region_tx[SHARED_MEM_TX_LOC_SIZE];
+
+uint8_t scratchpad_locked_rx = 1;
+uint8_t scratchpad_locked_tx = 1;
+
+
+void shared_memory_init(void)
+{
+    scratchpad_locked_rx = 1;
+    scratchpad_locked_tx = 1;
+
+}
+
+
+uint8_t shared_memory_scratchpad_region_save_helper(uint32_t addr)
+{
+
+
+
+#if DO_SHM_SCRATCHPAD
+    if (addr > (SHARED_MEM_TX_LOC_STATE + (SHARED_MEM_TX_LOC_SIZE))
+        && scratchpad_locked_tx) {
+        debug_P(DEBUG_SHM,
+                PSTR
+                ("shared_memory_scratchpad_region_save_helper: open tx addr=0x%06lx\n"),
+                addr);
+        shared_memory_scratchpad_region_tx_save();
+        return 0;
+    }
+    if (addr > (SHARED_MEM_RX_LOC_STATE + (SHARED_MEM_RX_LOC_SIZE))
+        && scratchpad_locked_rx) {
+        debug_P(DEBUG_SHM,
+                PSTR
+                ("shared_memory_scratchpad_region_save_helper: open rx addr=0x%06lx\n"),
+                addr);
+        shared_memory_scratchpad_region_rx_save();
+        return 0;
+    }
+#endif
+    return 1;
+}
+
+
+void shared_memory_scratchpad_region_tx_save()
+{
+    sram_bulk_addr_save();
+
+#if SHARED_SCRATCHPAD_CRC
+    uint16_t crc;
+    crc = crc_check_bulk_memory((uint32_t) SHARED_MEM_TX_LOC_STATE,
+                                (uint32_t) (SHARED_MEM_TX_LOC_STATE +
+                                            SHARED_MEM_TX_LOC_SIZE), 0x8000);
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_tx_save: crc=%x\n"), crc);
+
+#endif
+
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_tx_save: unlock\n"));
+    sram_bulk_copy_into_buffer((uint32_t) SHARED_MEM_TX_LOC_STATE,
+                               scratchpad_region_tx,
+                               (uint32_t) SHARED_MEM_TX_LOC_SIZE);
+    scratchpad_locked_tx = 0;
+
+#if SHARED_SCRATCHPAD_CRC
+    do_crc_update(0, scratchpad_region_tx, SHARED_MEM_TX_LOC_SIZE);
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_tx_save: crc=%x\n"), crc);
+#endif
+
+#if SHARED_SCRATCHPAD_DUMP
+    dump_packet(SHARED_MEM_TX_LOC_STATE, SHARED_MEM_TX_LOC_SIZE,
+                scratchpad_region_tx);
+    dump_memory(SHARED_MEM_TX_LOC_STATE,
+                SHARED_MEM_TX_LOC_STATE + SHARED_MEM_TX_LOC_SIZE);
+#endif
+    sram_bulk_addr_restore();
+
+}
+
+void shared_memory_scratchpad_region_rx_save()
+{
+
+    sram_bulk_addr_save();
+#if SHARED_SCRATCHPAD_CRC
+    uint16_t crc;
+    crc = crc_check_bulk_memory((uint32_t) SHARED_MEM_RX_LOC_STATE,
+                                (uint32_t) (SHARED_MEM_RX_LOC_STATE +
+                                            SHARED_MEM_RX_LOC_SIZE), 0x8000);
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_rx_save: crc=%x\n"), crc);
+#endif
+
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_rx_save: unlock\n"));
+    sram_bulk_copy_into_buffer((uint32_t) SHARED_MEM_RX_LOC_STATE,
+                               scratchpad_region_rx,
+                               (uint32_t) SHARED_MEM_RX_LOC_SIZE);
+    scratchpad_locked_rx = 0;
+
+#if SHARED_SCRATCHPAD_CRC
+    do_crc_update(0, scratchpad_region_rx, SHARED_MEM_RX_LOC_SIZE);
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_rx_save: crc=%x\n"), crc);
+#endif
+
+#if SHARED_SCRATCHPAD_DUMP
+    dump_packet(SHARED_MEM_RX_LOC_STATE, SHARED_MEM_RX_LOC_SIZE,
+                scratchpad_region_rx);
+    dump_memory(SHARED_MEM_RX_LOC_STATE,
+                SHARED_MEM_RX_LOC_STATE + SHARED_MEM_RX_LOC_SIZE);
+#endif
+    sram_bulk_addr_restore();
+
+}
+
+void shared_memory_scratchpad_region_tx_restore()
+{
+    if (scratchpad_locked_tx)
+        return;
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_tx_restore: lock\n"));
+
+#if SHARED_SCRATCHPAD_DUMP
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_tx_restore: memory\n"));
+    dump_memory(SHARED_MEM_TX_LOC_STATE,
+                SHARED_MEM_TX_LOC_STATE + SHARED_MEM_TX_LOC_SIZE);
+#endif
+
+    sram_bulk_copy_from_buffer((uint32_t) SHARED_MEM_TX_LOC_STATE,
+                               scratchpad_region_tx,
+                               (uint32_t) SHARED_MEM_TX_LOC_SIZE);
+    scratchpad_locked_tx = 1;
+
+#if SHARED_SCRATCHPAD_DUMP
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_tx_restore: buffer\n"));
+    dump_packet(SHARED_MEM_TX_LOC_STATE, SHARED_MEM_TX_LOC_SIZE,
+                scratchpad_region_tx);
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_tx_restore: memory\n"));
+    dump_memory(SHARED_MEM_TX_LOC_STATE,
+                SHARED_MEM_TX_LOC_STATE + SHARED_MEM_TX_LOC_SIZE);
+#endif
+
+#if SHARED_SCRATCHPAD_CRC
+    uint16_t crc;
+    crc = crc_check_bulk_memory((uint32_t) SHARED_MEM_TX_LOC_STATE,
+                                (uint32_t) (SHARED_MEM_TX_LOC_STATE +
+                                            SHARED_MEM_TX_LOC_SIZE), 0x8000);
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_tx_restore: crc=%x\n"), crc);
+#endif
+}
+
+
+void shared_memory_scratchpad_region_rx_restore()
+{
+    if (scratchpad_locked_rx)
+        return;
+
+
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_rx_restore: lock\n"));
+
+#if SHARED_SCRATCHPAD_DUMP
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_rx_restore: memory\n"));
+    dump_memory(SHARED_MEM_RX_LOC_STATE - 0x10,
+                SHARED_MEM_RX_LOC_STATE + SHARED_MEM_RX_LOC_SIZE);
+#endif
+
+    sram_bulk_copy_from_buffer((uint32_t) SHARED_MEM_RX_LOC_STATE,
+                               scratchpad_region_rx,
+                               (uint32_t) SHARED_MEM_RX_LOC_SIZE);
+    scratchpad_locked_rx = 1;
+
+#if SHARED_SCRATCHPAD_DUMP
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_rx_restore: buffer\n"));
+    dump_packet(SHARED_MEM_RX_LOC_STATE, SHARED_MEM_RX_LOC_SIZE,
+                scratchpad_region_rx);
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_rx_restore: memory\n"));
+    dump_memory(SHARED_MEM_RX_LOC_STATE - 0x10,
+                SHARED_MEM_RX_LOC_STATE + SHARED_MEM_RX_LOC_SIZE);
+#endif
+
+#if SHARED_SCRATCHPAD_CRC
+    uint16_t crc;
+    crc = crc_check_bulk_memory((uint32_t) SHARED_MEM_RX_LOC_STATE,
+                                (uint32_t) (SHARED_MEM_RX_LOC_STATE +
+                                            SHARED_MEM_RX_LOC_SIZE), 0x8000);
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_scratchpad_region_rx_restore: crc=%x\n"), crc);
+#endif
+}
+
+
 void shared_memory_scratchpad_tx_save()
 {
     scratchpad_state = sram_read(SHARED_MEM_TX_LOC_STATE);
@@ -69,18 +273,32 @@ void shared_memory_irq_restore()
 
 void shared_memory_write(uint8_t cmd, uint8_t value)
 {
+#if DO_SHM
+#if DO_SHM_SCRATCHPAD
+    if (scratchpad_locked_tx) {
+        debug_P(DEBUG_SHM, PSTR("shared_memory_write:  locked_tx\n"));
+        return;
+    }
+#endif
+    debug_P(DEBUG_SHM,
+            PSTR("shared_memory_write:  0x%04x=0x%02x 0x%04x=0x%02x \n"),
+            SHARED_MEM_TX_LOC_CMD, cmd, SHARED_MEM_TX_LOC_PAYLOAD, value);
 
-    debug(DEBUG_SHM,"shared_memory_write:  0x%04x=0x%02x 0x%04x=0x%02x \n",
+    sram_bulk_addr_save();
-         SHARED_MEM_TX_LOC_CMD, cmd, SHARED_MEM_TX_LOC_PAYLOAD, value);
 
+#if (DO_SHM_SCRATCHPAD==0)
     shared_memory_scratchpad_tx_save();
+#endif
+#if SHARED_MEM_SWITCH_IRQ
     shared_memory_irq_hook();
+#endif
 
     sram_write(SHARED_MEM_TX_LOC_STATE, SHARED_MEM_TX_SNES_ACK);
     sram_write(SHARED_MEM_TX_LOC_CMD, cmd);
     sram_write(SHARED_MEM_TX_LOC_PAYLOAD, value);
 
     snes_hirom();
+    snes_wr_disable();
     snes_bus_active();
 
 #if SHARED_MEM_SWITCH_IRQ
@@ -94,11 +312,19 @@ void shared_memory_write(uint8_t cmd, uint8_t value)
 #endif
 
     avr_bus_active();
+    snes_irq_lo();
+    snes_irq_off();
     snes_lorom();
+    snes_wr_disable();
 
+#if (DO_SHM_SCRATCHPAD==0)
     shared_memory_scratchpad_tx_restore();
+#endif
+#if SHARED_MEM_SWITCH_IRQ
     shared_memory_irq_restore();
-
+#endif
+    sram_bulk_addr_restore();
+#endif
 }
 
 void shared_memory_yield()
@@ -115,25 +341,35 @@ void shared_memory_yield()
 }
 
 
-int shared_memory_read(uint8_t *cmd, uint8_t *len,uint8_t *buffer)
+int shared_memory_read(uint8_t * cmd, uint8_t * len, uint8_t * buffer)
 {
-    uint8_t state;
+    // uint8_t state;
-
+#if DO_SHM
+#if DO_SHM_SCRATCHPAD
+    if (scratchpad_locked_rx) {
+        debug_P(DEBUG_SHM, PSTR("shared_memory_write:  locked_tx\n"));
+        return 1;
+    }
+#endif
+    sram_bulk_addr_save();
 
     state = sram_read(SHARED_MEM_RX_LOC_STATE);
-    if (state != SHARED_MEM_RX_AVR_ACK){
+    if (state != SHARED_MEM_RX_AVR_ACK) {
+        sram_bulk_addr_restore();
         return 1;
     }
 
     *cmd = sram_read(SHARED_MEM_RX_LOC_CMD);
     *len = sram_read(SHARED_MEM_RX_LOC_LEN);
-    debug(DEBUG_SHM,"shared_memory_read: 0x%04x=0x%02x 0x%04x=0x%02x \n",
+    debug_P(DEBUG_SHM,
-         SHARED_MEM_RX_LOC_CMD, *cmd, SHARED_MEM_RX_LOC_LEN, *len);
+            PSTR("shared_memory_read: 0x%04x=0x%02x 0x%04x=0x%02x \n"),
+            SHARED_MEM_RX_LOC_CMD, *cmd, SHARED_MEM_RX_LOC_LEN, *len);
 
-    sram_bulk_read_buffer(SHARED_MEM_RX_LOC_PAYLOAD,buffer, *len);
+    sram_bulk_copy_into_buffer(SHARED_MEM_RX_LOC_PAYLOAD, buffer, *len);
     sram_write(SHARED_MEM_RX_LOC_STATE, SHARED_MEM_RX_AVR_RTS);
 
     snes_hirom();
+    snes_wr_disable();
     snes_bus_active();
 
 #if SHARED_MEM_SWITCH_IRQ
@@ -148,5 +384,8 @@ int shared_memory_read(uint8_t *cmd, uint8_t *len,uint8_t *buffer)
 
     avr_bus_active();
     snes_lorom();
+    snes_wr_disable();
+    sram_bulk_addr_restore();
+#endif
     return 0;
 }

avr/usbload/shared_memory.h

@@ -37,6 +37,7 @@
 #define SHARED_MEM_TX_CMD_TERMINATE         0x06
 
 #define SHARED_MEM_TX_LOC_STATE             0x000000
+#define SHARED_MEM_TX_LOC_SIZE              0x000040
 #define SHARED_MEM_TX_LOC_CMD               0x000001
 #define SHARED_MEM_TX_LOC_PAYLOAD           0x000002
 
@@ -47,6 +48,7 @@
 #define SHARED_MEM_RX_CMD_FILESEL           0x01
 
 #define SHARED_MEM_RX_LOC_STATE             0x001000
+#define SHARED_MEM_RX_LOC_SIZE              0x000040
 #define SHARED_MEM_RX_LOC_CMD               0x001001
 #define SHARED_MEM_RX_LOC_LEN               0x001002
 #define SHARED_MEM_RX_LOC_PAYLOAD           0x001003
@@ -54,10 +56,23 @@
 #define SHARED_IRQ_LOC_LO                   0x00fffe
 #define SHARED_IRQ_LOC_HI                   0x00ffff
 
-#define SHARED_IRQ_HANDLER_LO               0x00
+/*
-#define SHARED_IRQ_HANDLER_HI               0x10
+ * Use COP IRQ LOC for hooked IRQ handler 
+ */
+#define SHARED_IRQ_HANDLER_LO               0x0ffe4
+#define SHARED_IRQ_HANDLER_HI               0x0ffe5
 
+#define SHARED_SCRATCHPAD_DUMP              0
+#define SHARED_SCRATCHPAD_CRC               0
+
+
+void shared_memory_init(void);
+uint8_t shared_memory_scratchpad_region_save_helper(uint32_t addr);
+void shared_memory_scratchpad_region_tx_save();
+void shared_memory_scratchpad_region_tx_restore();
+void shared_memory_scratchpad_region_rx_save();
+void shared_memory_scratchpad_region_rx_restore();
 void shared_memory_write(uint8_t cmd, uint8_t value);
-int shared_memory_read(uint8_t *cmd, uint8_t *len,uint8_t *buffer);
+int shared_memory_read(uint8_t * cmd, uint8_t * len, uint8_t * buffer);
 
 #endif

avr/usbload/shell.c

@@ -0,0 +1,495 @@
+/*
+ * =====================================================================================
+ *
+ * ________        .__        __    ________               ____  ________
+ * \_____  \  __ __|__| ____ |  | __\______ \   _______  _/_   |/  _____/
+ *  /  / \  \|  |  \  |/ ___\|  |/ / |    |  \_/ __ \  \/ /|   /   __  \
+ * /   \_/.  \  |  /  \  \___|    <  |    `   \  ___/\   / |   \  |__\  \
+ * \_____\ \_/____/|__|\___  >__|_ \/_______  /\___  >\_/  |___|\_____  /
+ *        \__>             \/     \/        \/     \/                 \/
+ *
+ *                                  www.optixx.org
+ *
+ *
+ *        Version:  1.0
+ *        Created:  07/21/2009 03:32:16 PM
+ *         Author:  david@optixx.org
+ *
+ * =====================================================================================
+ */
+#include <stdint.h>
+#include <string.h>
+#include <avr/io.h>
+#include <stdlib.h>
+#include <avr/interrupt.h>
+#include <util/delay.h>
+#include <avr/pgmspace.h>
+#include <avr/eeprom.h>
+
+
+#include "pwm.h"
+#include "debug.h"
+#include "info.h"
+#include "sram.h"
+#include "util.h"
+#include "uart.h"
+#include "dump.h"
+#include "irq.h"
+#include "config.h"
+#include "crc.h"
+#include "command.h"
+#include "shared_memory.h"
+#include "system.h"
+
+
+extern system_t my_system;
+
+const char STR_ROM[] PROGMEM = "Rom";
+const char STR_RAM[] PROGMEM = "Sram";
+const char STR_BAT[] PROGMEM = "Battery";
+const char STR_SUPERFX[] PROGMEM = "SuperFX";
+const char STR_SA[] PROGMEM = "SA-1";
+
+
+uint8_t command_buf[RECEIVE_BUF_LEN];
+uint8_t recv_buf[RECEIVE_BUF_LEN];
+
+volatile uint8_t recv_counter = 0;
+volatile uint8_t cr = 0;
+
+uint8_t *token_ptr;
+
+#if DO_SHELL
+
+uint8_t *get_token(void)
+{
+    uint8_t *p = token_ptr;
+    while (*p == ' ')
+        p++;
+    if (*p == '\0')
+        return NULL;
+    token_ptr = p;
+    do {
+        token_ptr++;
+        if (*token_ptr == ' ' || *token_ptr == '\n' || *token_ptr == '\r') {
+            *token_ptr++ = '\0';
+            break;
+        }
+    } while (*token_ptr != ' ' && *token_ptr != '\n' && *token_ptr != '\r');
+    return p;
+}
+
+uint8_t get_dec(uint32_t * decval)
+{
+    const uint8_t *t;
+    t = get_token();
+    if (t != NULL) {
+        int x = util_sscandec(t);
+        if (x < 0)
+            return 0;
+        *decval = x;
+        return 1;
+    }
+    return 0;
+}
+
+uint8_t parse_hex(const uint8_t * s, uint32_t * hexval)
+{
+    uint32_t x = util_sscanhex(s);
+    *hexval = (uint32_t) x;
+    return 1;
+}
+
+uint8_t get_hex(uint32_t * hexval)
+{
+    const uint8_t *t;
+    t = get_token();
+    if (t != NULL)
+        return parse_hex(t, hexval);
+    return 0;
+}
+
+uint8_t get_hex_arg2(uint32_t * hexval1, uint32_t * hexval2)
+{
+    return get_hex(hexval1) && get_hex(hexval2);
+}
+
+uint8_t get_hex_arg3(uint32_t * hexval1, uint32_t * hexval2, uint32_t * hexval3)
+{
+    return get_hex(hexval1) && get_hex(hexval2) && get_hex(hexval3);
+}
+
+#if 0
+static uint8_t get_int32(uint32_t * val)
+{
+    if (!get_hex(val)) {
+        info_P(PSTR("Invalid argument!\n"));
+        return 0;
+    } else {
+        return 1;
+    }
+}
+
+static uint8_t get_int8(uint8_t * val)
+{
+    uint32_t ret;
+    if (!get_hex(&ret) || ret > 0xff) {
+        info_P(PSTR("Invalid argument!\n"));
+        return 0;
+    } else {
+        *val = (uint8_t) ret;
+        return 1;
+    }
+}
+#endif
+static int get_bool(void)
+{
+    const uint8_t *t;
+    t = get_token();
+    if (t != NULL) {
+        int result = util_sscanbool(t);
+        if (result >= 0)
+            return result;
+    }
+    info_P(PSTR("Invalid argument (should be 0 or 1)!\n"));
+    return -1;
+}
+void prompt(void)
+{
+
+    uart_putc('\r');
+    uart_putc('\n');
+    uart_putc('>');
+
+}
+
+ISR(USART0_RX_vect)
+{
+    UCSR0B &= (255 - (1 << RXCIE0));    // Interrupts disable for RxD
+    sei();
+    if (recv_counter == (sizeof(recv_buf) - 1)) {
+        cr = 1;
+        recv_buf[recv_counter] = '\0';
+        recv_counter = 0;
+        prompt();
+    }
+    recv_buf[recv_counter] = UDR0;
+    uart_putc(recv_buf[recv_counter]);
+    if (recv_buf[recv_counter] == 0x0d) {
+        /*
+         * recv_buf[recv_counter] = 0; 
+         */
+        cr = 1;
+        recv_buf[++recv_counter] = '\0';
+        recv_counter = 0;
+        prompt();
+    } else {
+        // we accept backspace or delete
+        if ((recv_buf[recv_counter] == 0x08 || recv_buf[recv_counter] == 0x7f)
+            && recv_counter > 0) {
+            recv_counter--;
+        } else {
+            recv_counter++;
+        }
+    }
+    UCSR0B |= (1 << RXCIE0);
+}
+
+enum cmds {
+    CMD_DUMP,
+    CMD_DUMPVEC,
+    CMD_DUMPHEADER,
+#if DO_CRC_CHECK
+    CMD_CRC,
+#endif
+    CMD_EXIT,
+    CMD_RESET,
+    CMD_RESETSNIFF,
+    CMD_IRQ,
+    CMD_AVR,
+    CMD_SNES,
+    CMD_LOROM,
+    CMD_HIROM,
+    CMD_WR,
+    CMD_SHMWR,
+    CMD_SHMSAVE,
+    CMD_SHMRESTORE,
+    CMD_LOADER,
+    CMD_RECONNECT,
+    CMD_STATUS,
+    CMD_SYS,
+    CMD_HELP
+};
+
+const uint8_t cmdlist[][CMD_HELP] PROGMEM = {
+    {"DUMP"},
+    {"DUMPVEC"},
+    {"DUMPHEADER"},
+#if DO_CRC_CHECK
+    {"CRC"},
+#endif
+    {"EXIT"},
+    {"RESET"},
+    {"RESETSNIFF"},
+    {"IRQ"},
+    {"AVR"},
+    {"SNES"},
+    {"LOROM"},
+    {"HIROM"},
+    {"WR"},
+    {"SHMWR"},
+    {"SHMSAVE"},
+    {"SHMRESTORE"},
+    {"LOADER"},
+    {"RECONNECT"},
+    {"STATUS"},
+    {"SYS"},
+    {"HELP"},
+};
+
+
+void shell_help(void)
+{
+    uint8_t i;
+    info_P(PSTR("\n"));
+    for (i = CMD_DUMP; i < CMD_HELP; i++) {
+        info_P((PGM_P) cmdlist[i]);
+        info_P(PSTR("\n"));
+
+    }
+}
+
+
+void shell_run(void)
+{
+    uint8_t *t;
+    uint32_t arg1;
+    uint32_t arg2;
+    uint16_t crc;
+    uint16_t offset;
+    uint8_t c;
+
+    if (!cr)
+        return;
+    cr = 0;
+    strcpy((char *) command_buf, (char *) recv_buf);
+
+    token_ptr = command_buf;
+    t = get_token();
+
+    if (t == NULL)
+        shell_help();
+
+    util_strupper(t);
+
+    if (strcmp_P((const char *) t, (PGM_P) cmdlist[CMD_DUMP]) == 0) {
+        if (get_hex_arg2(&arg1, &arg2))
+            dump_memory(arg1, arg2);
+        else
+            info_P(PSTR("DUMP <start addr> <end addr>\n"));
+
+#if DO_CRC_CHECK
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_CRC]) == 0) {
+        if (get_hex_arg2(&arg1, &arg2)) {
+            crc = crc_check_bulk_memory(arg1, arg2, 0x8000);
+            info_P(PSTR("0x%06lx - 0x%06lx crc=0x%04x\n"), arg1, arg2, crc);
+        } else
+            info_P(PSTR("CRC <start addr> <end addr>\n"));
+#endif
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_EXIT]) == 0) {
+        leave_application();
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_RESET]) == 0) {
+        system_send_snes_reset();
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_IRQ]) == 0) {
+        info_P(PSTR("Send IRQ\n"));
+        snes_irq_on();
+        snes_irq_lo();
+        _delay_us(20);
+        snes_irq_hi();
+        snes_irq_off();
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_AVR]) == 0) {
+        system_set_bus_avr();
+        snes_irq_lo();
+        system_snes_irq_off();
+
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_SNES]) == 0) {
+        snes_irq_lo();
+        system_snes_irq_off();
+        system_set_wr_disable();
+        system_set_bus_snes();
+
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_LOROM]) == 0) {
+        system_set_rom_lorom();
+        system_set_wr_disable();
+
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_HIROM]) == 0) {
+        system_set_rom_hirom();
+        system_set_wr_disable();
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_WR]) == 0) {
+        arg1 = get_bool();
+        if (arg1 == 1) {
+            info_P(PSTR("Set WR enable"));
+            snes_wr_enable();
+        } else if (arg1 == 0) {
+            info_P(PSTR("Set WR disable"));
+            snes_wr_disable();
+        }
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_RESETSNIFF]) == 0) {
+        arg1 = get_bool();
+        if (arg1 == 1) {
+            info_P(PSTR("Start Reset sniffer"));
+            irq_init();
+        } else if (arg1 == 0) {
+            info_P(PSTR("Stop Reset sniffer"));
+            irq_stop();
+        }
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_DUMPVEC]) == 0) {
+        uint16_t offset;
+        if (my_system.rom_mode == LOROM)
+            offset = 0x8000;
+        else
+            offset = 0x0000;
+
+        info_P(PSTR("ABORT  0x%04x 0x%04x\n"), (0xFFE8 - offset),
+               sram_read16_be(0xFFE8 - offset));
+        info_P(PSTR("BRK    0x%04x 0x%04x\n"), (0xFFE6 - offset),
+               sram_read16_be(0xFFE6 - offset));
+        info_P(PSTR("COP    0x%04x 0x%04x\n"), (0xFFE4 - offset),
+               sram_read16_be(0xFFE4 - offset));
+        info_P(PSTR("IRQ    0x%04x 0x%04x\n"), (0xFFEE - offset),
+               sram_read16_be(0xFFEE - offset));
+        info_P(PSTR("NMI    0x%04x 0x%04x\n"), (0xFFEA - offset),
+               sram_read16_be(0xFFEA - offset));
+        info_P(PSTR("RES    0x%04x 0x%04x\n"), (0xFFFC - offset),
+               sram_read16_be(0xFFFC - offset));
+
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_DUMPHEADER]) == 0) {
+
+        if (my_system.rom_mode == LOROM)
+            offset = 0x8000;
+        else
+            offset = 0x0000;
+        /*
+         * # $ffc0..$ffd4 => Name of the ROM, typically in ASCII, using spaces to pad the name to 21 bytes. # $ffd5 => ROM layout,
+         * typically $20 for LoROM, or $21 for HiROM. Add $10 for FastROM. # $ffd6 => Cartridge type, typically $00 for ROM only, or $02
+         * for ROM with save-RAM. # $ffd7 => ROM size byte. # $ffd8 => RAM size byte. # $ffd9 => Country code, which selects the video in
+         * the emulator. Values $00, $01, $0d use NTSC. Values in range $02..$0c use PAL. Other values are invalid. # $ffda => Licensee
+         * code. If this value is $33, then the ROM has an extended header with ID at $ffb2..$ffb5. # $ffdb => Version number, typically
+         * $00. # $ffdc..$ffdd => Checksum complement, which is the bitwise-xor of the checksum and $ffff. # $ffde..$ffdf => SNES checksum, 
+         * an unsigned 16-bit checksum of bytes. # $ffe0..$ffe3 => Unknown. 
+         */
+        info_P(PSTR("NAME   0x%04x "), (0xffc0 - offset));
+        for (arg1 = (0xffc0 - offset); arg1 < (0xffc0 - offset + 21); arg1++) {
+            c = sram_read(arg1);
+            if (c > 0x1f && c < 0x7f)
+                printf("%c", c);
+        }
+        printf("\n");
+        c = sram_read(0xffd5 - offset);
+        info_P(PSTR("LAYOUT 0x%04x "), (0xffd5 - offset));
+
+        switch (c) {
+            case 0x20:
+                info_P(PSTR("LoROM, not fast\n"));
+                break;
+            case 0x21:
+                info_P(PSTR("HiRom, not fast\n"));
+                break;
+            case 0x30:
+                info_P(PSTR("LoROM, fast\n"));
+                break;
+            case 0x31:
+                info_P(PSTR("HiRom, fast\n"));
+                break;
+            default:
+                info_P(PSTR("Unkown 0x%02x\n"), c);
+                break;
+        }
+
+        c = sram_read(0xffd6 - offset);
+        info_P(PSTR("TYPE   0x%04xc"), (0xffd6 - offset), c);
+        switch (c) {
+            case 0x00:
+                info_P(PSTR("Rom\n"));
+                break;
+            case 0x01:
+                info_P(PSTR("Rom + Sram\n"));
+                break;
+            case 0x02:
+                info_P(PSTR("Rom + Sram + Battery\n"));
+                break;
+            case 0x13:
+                info_P(PSTR("SuperFX\n"));
+                break;
+            case 0x14:
+                info_P(PSTR("SuperFX\n"));
+                break;
+            case 0x15:
+                info_P(PSTR("SuperFX + Sram\n"));
+                break;
+            case 0x1a:
+                info_P(PSTR("SuperFX + Sram\n"));
+                break;
+            case 0x34:
+                info_P(PSTR("SA-1"));
+                break;
+            case 0x35:
+                info_P(PSTR("SA-1"));
+                break;
+            default:
+                info_P(PSTR("Unkown 0x%02x\n"), c);
+                break;
+        }
+        arg1 = (2 << (sram_read(0xffd7 - offset) - 1));
+        info_P(PSTR("ROM    0x%04x %li MBit ( %li KiB)\n"),
+               (0xffd7 - offset), (arg1 / 128), arg1);
+        arg1 = (2 << (sram_read(0xffd8 - offset) - 1));
+        info_P(PSTR("RAM    0x%04x %li KiB\n"), (0xffd8 - offset), arg1);
+
+        info_P(PSTR("CCODE  0x%04x "), (0xffd9 - offset));
+        c = sram_read(0xffd9 - offset);
+        if (c == 0x00 || c == 0x01 || 0x0d)
+            info_P(PSTR("NTSC\n"));
+        else if (c >= 0x02 || c <= 0x0c)
+            info_P(PSTR("PAL\n"));
+        else
+            info_P(PSTR("Unkown 0x%02x\n"), c);
+
+        info_P(PSTR("LIC    0x%04x 0x%02x\n"), (0xffda - offset),
+               sram_read(0xffda - offset));
+        info_P(PSTR("VER    0x%04x 0x%02x\n"), (0xffdb - offset),
+               sram_read(0xffdb - offset));
+        info_P(PSTR("SUM1   0x%04x 0x%04x\n"), (0xffdc - offset),
+               sram_read16_be(0xffdc - offset));
+        info_P(PSTR("SUM2   0x%04x 0x%04x\n"), (0xffde - offset),
+               sram_read16_be(0xffde - offset));
+
+
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_SHMWR]) == 0) {
+        if (get_hex_arg2(&arg1, &arg2))
+            shared_memory_write((uint8_t) arg1, (uint8_t) arg1);
+        else
+            info_P(PSTR("SHMWR <command> <value>\n"));
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_SHMSAVE]) == 0) {
+        shared_memory_scratchpad_region_tx_save();
+        shared_memory_scratchpad_region_rx_save();
+        info_P(PSTR("Save scratchpad\n"));
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_SHMRESTORE]) == 0) {
+        shared_memory_scratchpad_region_tx_restore();
+        shared_memory_scratchpad_region_rx_restore();
+        info_P(PSTR("Restore scratchpad\n"));
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_LOADER]) == 0) {
+        boot_startup_rom(500);
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_RECONNECT]) == 0) {
+        usb_connect();
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_STATUS]) == 0) {
+        transaction_status();
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_SYS]) == 0) {
+        system_status();
+    } else if (strcmp_P((char *) t, (PGM_P) cmdlist[CMD_HELP]) == 0) {
+        shell_help();
+    }
+    prompt();
+}
+
+#endif

avr/usbload/shell.h

@@ -0,0 +1,26 @@
+/*
+ * =====================================================================================
+ *
+ * ________        .__        __    ________               ____  ________
+ * \_____  \  __ __|__| ____ |  | __\______ \   _______  _/_   |/  _____/
+ *  /  / \  \|  |  \  |/ ___\|  |/ / |    |  \_/ __ \  \/ /|   /   __  \
+ * /   \_/.  \  |  /  \  \___|    <  |    `   \  ___/\   / |   \  |__\  \
+ * \_____\ \_/____/|__|\___  >__|_ \/_______  /\___  >\_/  |___|\_____  /
+ *        \__>             \/     \/        \/     \/                 \/
+ *
+ *                                  www.optixx.org
+ *
+ *
+ *        Version:  1.0
+ *        Created:  07/21/2009 03:32:16 PM
+ *         Author:  david@optixx.org
+ *
+ * =====================================================================================
+ */
+
+#ifndef __SHELL_H__
+#define __SHELL_H__
+
+void shell_run(void);
+
+#endif

avr/usbload/sram.c

@@ -31,81 +31,82 @@
 #include "debug.h"
 #include "info.h"
 
-void system_init(void)
+uint32_t addr_current = 0;
+uint32_t addr_stash = 0;
+
+void sram_init(void)
 {
     /*-------------------------------------------------*/
 
-    DDRA =  0x00;
+    DDRA = 0x00;
-    PORTA =  0x00;
+    PORTA = 0x00;
 
     /*-------------------------------------------------*/
 
-    DDRC |=     ( (1 << AVR_ADDR_LATCH_PIN)	    
+    DDRC |= ((1 << AVR_ADDR_LATCH_PIN)
-                | (1 << AVR_ADDR_SCK_PIN)	    
+             | (1 << AVR_ADDR_SCK_PIN)
-                | (1 << AVR_ADDR_SER_PIN)	    
+             | (1 << AVR_ADDR_SER_PIN)
-                | (1 << AVR_ADDR_LOAD_PIN)	    
+             | (1 << AVR_ADDR_LOAD_PIN)
-                | (1 << AVR_ADDR_DOWN_PIN)	    
+             | (1 << AVR_ADDR_UP_PIN));
-                | (1 << AVR_ADDR_UP_PIN));
 
-    DDRC &=     ~ (1 << SNES_WR_PIN);	    
+    DDRC &= ~((1 << SNES_WR_PIN)
+              | (1 << AVR_BTLDR_EN_PIN));
 
-    PORTC &=    ~((1 << AVR_ADDR_LATCH_PIN)	    
+    PORTC &= ~((1 << AVR_ADDR_LATCH_PIN)
-                | (1 << AVR_ADDR_SCK_PIN)
+               | (1 << AVR_ADDR_SCK_PIN)
-                | (1 << SNES_WR_PIN));
+               | (1 << SNES_WR_PIN));
 
 
-    PORTC |=    ( (1 << AVR_ADDR_DOWN_PIN)	    
+    PORTC |= ((1 << AVR_ADDR_UP_PIN)
-                | (1 << AVR_ADDR_UP_PIN)
+              | (1 << AVR_ADDR_LOAD_PIN));
-                | (1 << AVR_ADDR_LOAD_PIN));    
 
-                //| (1 << SNES_WR_PIN));
+    // | (1 << SNES_WR_PIN));
     /*-------------------------------------------------*/
 
-    DDRB |=     ( (1 << AVR_RD_PIN)	            
+    DDRB |= ((1 << AVR_RD_PIN)
-                | (1 << AVR_WR_PIN) 
+             | (1 << AVR_WR_PIN)
-                | (1 << AVR_CS_PIN)	            
+             | (1 << AVR_CS_PIN)
-                | (1 << SNES_IRQ_PIN));
+             | (1 << SNES_IRQ_PIN));
 
 
-    PORTB |=    ( (1 << AVR_RD_PIN)	            
+    PORTB |= ((1 << AVR_RD_PIN)
-                | (1 << AVR_WR_PIN) 
+              | (1 << AVR_WR_PIN)
-                | (1 << AVR_CS_PIN)	            
+              | (1 << AVR_CS_PIN)
-                | (1 << SNES_IRQ_PIN));
+              | (1 << SNES_IRQ_PIN));
 
     /*-------------------------------------------------*/
 
 
-    DDRD |=     ( (1 << AVR_SNES_SW_PIN)	            
+    DDRD |= ((1 << AVR_SNES_SW_PIN)
-                | (1 << HI_LOROM_SW_PIN) 
+             | (1 << HI_LOROM_SW_PIN)
-                | (1 << SNES_WR_EN_PIN));
+             | (1 << SNES_WR_EN_PIN));
 
-    PORTD |=    (1 << HI_LOROM_SW_PIN);
+    PORTD |= (1 << HI_LOROM_SW_PIN);
 
-    PORTD &=    ~((1 << AVR_SNES_SW_PIN) 
+    PORTD &= ~((1 << AVR_SNES_SW_PIN)
-                | (1 << SNES_WR_EN_PIN));
+               | (1 << SNES_WR_EN_PIN));
 
     /*-------------------------------------------------*/
 
 
 }
 
-
 void sreg_set(uint32_t addr)
 {
     uint8_t i = 24;
-    debug(DEBUG_SREG,"sreg_set: addr=0x%08lx",addr);
+    debug_P(DEBUG_SREG, PSTR("sreg_set: addr=0x%08lx"), addr);
-    while(i--) {
+    while (i--) {
-        if ((addr & ( 1L << i))){
+        if ((addr & (1L << i))) {
-            debug(DEBUG_SREG,"1");
+            debug_P(DEBUG_SREG, PSTR("1"));
-            AVR_ADDR_SER_PORT |= ( 1 << AVR_ADDR_SER_PIN);
+            AVR_ADDR_SER_PORT |= (1 << AVR_ADDR_SER_PIN);
         } else {
-            AVR_ADDR_SER_PORT &= ~( 1 << AVR_ADDR_SER_PIN);
+            AVR_ADDR_SER_PORT &= ~(1 << AVR_ADDR_SER_PIN);
-            debug(DEBUG_SREG,"0");
+            debug_P(DEBUG_SREG, PSTR("0"));
         }
         AVR_ADDR_SCK_PORT |= (1 << AVR_ADDR_SCK_PIN);
         AVR_ADDR_SCK_PORT &= ~(1 << AVR_ADDR_SCK_PIN);
     }
-    debug(DEBUG_SREG,"\n");
+    debug_P(DEBUG_SREG, PSTR("\n"));
     AVR_ADDR_LATCH_PORT |= (1 << AVR_ADDR_LATCH_PIN);
     AVR_ADDR_LATCH_PORT &= ~(1 << AVR_ADDR_LATCH_PIN);
 
@@ -113,11 +114,27 @@ void sreg_set(uint32_t addr)
 
 }
 
+void sram_bulk_addr_save()
+{
+    addr_stash = addr_current;
+    debug_P(DEBUG_SRAM, PSTR("sram_bulk_addr_save: addr=0x%08lx\n\r"),
+            addr_stash);
+}
+
+inline void sram_bulk_addr_restore()
+{
+    debug_P(DEBUG_SRAM, PSTR("sram_bulk_addr_restore: addr=0x%08lx\n\r"),
+            addr_stash);
+    sram_bulk_write_start(addr_stash);
+}
 
 
 void sram_bulk_read_start(uint32_t addr)
 {
-    debug(DEBUG_SRAM,"sram_bulk_read_start: addr=0x%08lx\n\r", addr);
+    debug_P(DEBUG_SRAM, PSTR("sram_bulk_read_start: addr=0x%08lx\n\r"), addr);
+
+    addr_current = addr;
+
     avr_data_in();
 
     AVR_CS_PORT &= ~(1 << AVR_CS_PIN);
@@ -134,10 +151,11 @@ void sram_bulk_read_start(uint32_t addr)
     asm volatile ("nop");
     asm volatile ("nop");
 
- }
+}
 
 inline void sram_bulk_read_next(void)
 {
+    addr_current++;
     AVR_RD_PORT |= (1 << AVR_RD_PIN);
     counter_up();
     AVR_RD_PORT &= ~(1 << AVR_RD_PIN);
@@ -159,7 +177,7 @@ inline uint8_t sram_bulk_read(void)
 
 void sram_bulk_read_end(void)
 {
-    debug(DEBUG_SRAM,"sram_bulk_read_end:\n");
+    debug_P(DEBUG_SRAM, PSTR("sram_bulk_read_end:\n"));
 
     AVR_RD_PORT |= (1 << AVR_RD_PIN);
     AVR_CS_PORT |= (1 << AVR_CS_PIN);
@@ -169,7 +187,7 @@ void sram_bulk_read_end(void)
 uint8_t sram_read(uint32_t addr)
 {
     uint8_t byte;
-    debug(DEBUG_SRAM_RAW,"sram_read: addr=0x%08lx\n\r", addr);
+    debug_P(DEBUG_SRAM_RAW, PSTR("sram_read: addr=0x%08lx\n\r"), addr);
 
     avr_data_in();
 
@@ -199,9 +217,17 @@ uint8_t sram_read(uint32_t addr)
 
 }
 
+uint16_t sram_read16_be(uint32_t addr)
+{
+    uint8_t hi = sram_read(addr);
+    uint8_t lo = sram_read(addr + 1);
+    return (hi << 8 | lo);
+}
+
 void sram_bulk_write_start(uint32_t addr)
 {
-    debug(DEBUG_SRAM,"sram_bulk_write_start: addr=0x%08lx\n\r", addr);
+    debug_P(DEBUG_SRAM, PSTR("sram_bulk_write_start: addr=0x%08lx\n\r"), addr);
+    addr_current = addr;
 
     avr_data_out();
 
@@ -211,25 +237,24 @@ void sram_bulk_write_start(uint32_t addr)
 
     sreg_set(addr);
 
-    AVR_WR_PORT &= ~(1 << AVR_WR_PIN);
-
 }
 
 inline void sram_bulk_write_next(void)
 {
-    AVR_WR_PORT |= (1 << AVR_WR_PIN);
+    addr_current++;
     counter_up();
-    AVR_WR_PORT &= ~(1 << AVR_WR_PIN);
 }
 
-inline void sram_bulk_write( uint8_t data)
+inline void sram_bulk_write(uint8_t data)
 {
+    AVR_WR_PORT &= ~(1 << AVR_WR_PIN);
     AVR_DATA_PORT = data;
-    }
+    AVR_WR_PORT |= (1 << AVR_WR_PIN);
+}
 
 void sram_bulk_write_end(void)
 {
-    debug(DEBUG_SRAM,"sram_bulk_write_end:");
+    debug_P(DEBUG_SRAM, PSTR("sram_bulk_write_end:"));
     AVR_WR_PORT |= (1 << AVR_WR_PIN);
     AVR_CS_PORT |= (1 << AVR_CS_PIN);
     avr_data_in();
@@ -238,7 +263,8 @@ void sram_bulk_write_end(void)
 
 void sram_write(uint32_t addr, uint8_t data)
 {
-    debug(DEBUG_SRAM_RAW,"sram_write: addr=0x%08lx data=%x\n\r", addr, data);
+    debug_P(DEBUG_SRAM_RAW, PSTR("sram_write: addr=0x%08lx data=%x\n\r"), addr,
+            data);
 
     avr_data_out();
 
@@ -267,45 +293,54 @@ void sram_write(uint32_t addr, uint8_t data)
 }
 
 
-void sram_bulk_copy(uint32_t addr, uint8_t * src, uint32_t len)
+void sram_bulk_copy_from_buffer(uint32_t addr, uint8_t * src, uint32_t len)
 {
 
     uint32_t i;
     uint8_t *ptr = src;
-    debug(DEBUG_SRAM,"sram_copy: addr=0x%08lx src=0x%p len=%li\n\r", addr,src,len);
+    debug_P(DEBUG_SRAM,
+            PSTR
+            ("sram_bulk_copy_from_buffer: addr=0x%08lx src=0x%p len=%li\n\r"),
+            addr, src, len);
     sram_bulk_write_start(addr);
-    for (i = addr; i < (addr + len); i++){
+    for (i = addr; i < (addr + len); i++) {
-        sram_bulk_write(*ptr++);
+        sram_bulk_write(*ptr);
-        sram_bulk_write_next();
+        // hack
+        if ((i + 1) < (addr + len))
+            sram_bulk_write_next();
+        ptr++;
     }
     sram_bulk_write_end();
 }
 
-void sram_bulk_read_buffer(uint32_t addr, uint8_t * dst, uint32_t len)
+void sram_bulk_copy_into_buffer(uint32_t addr, uint8_t * dst, uint32_t len)
 {
 
     uint32_t i;
-    uint8_t *ptr = dst;
+    // uint8_t *ptr = dst;
-    debug(DEBUG_SRAM,"sram_bulk_read_buffer: addr=0x%08lx dst=0x%p len=%li\n\r", addr,dst,len);
+    debug_P(DEBUG_SRAM,
+            PSTR
+            ("sram_bulk_copy_into_buffer: addr=0x%08lx dst=0x%p len=%li\n\r"),
+            addr, dst, len);
     sram_bulk_read_start(addr);
     for (i = addr; i < (addr + len); i++) {
-        *ptr = sram_bulk_read();
+        dst[i] = sram_bulk_read();
         sram_bulk_read_next();
-        ptr++;
     }
     sram_bulk_read_end();
 }
 
-void sram_bulk_set(uint32_t addr, uint32_t len,uint8_t value){
+void sram_bulk_set(uint32_t addr, uint32_t len, uint8_t value)
+{
     uint32_t i;
-    debug(DEBUG_SRAM,"sram_bulk_set: addr=0x%08lx len=%li\n\r", addr,len);
+    debug_P(DEBUG_SRAM, PSTR("sram_bulk_set: addr=0x%08lx len=%li\n\r"), addr,
+            len);
     sram_bulk_write_start(addr);
     for (i = addr; i < (addr + len); i++) {
         if (0 == i % 0xfff)
-            debug(DEBUG_SRAM,"sram_bulk_set: addr=0x%08lx\n\r", i);
+            debug_P(DEBUG_SRAM, PSTR("sram_bulk_set: addr=0x%08lx\n\r"), i);
         sram_bulk_write(value);
         sram_bulk_write_next();
     }
     sram_bulk_write_end();
 }
-

avr/usbload/sram.h

@@ -29,7 +29,9 @@
 
 
 
-/* ---------------------------- PORT A ---------------------------- */
+/*
+ * ---------------------------- PORT A ---------------------------- 
+ */
 
 #define AVR_DATA_PORT           PORTA
 #define AVR_DATA_DIR            DDRA
@@ -40,16 +42,10 @@
 
 #define avr_data_out()          (AVR_DATA_DIR = 0xff)
 
-#define LED_PORT	            PORTC
-#define LED_DIR		            DDRC
-#define LED_PIN		            PC7
 
-#define led_on()	            ((LED_PORT &=~ (1 << LED_PIN)),\
+/*
-                                (LED_DIR &=~ (1 << LED_PIN)))
+ * ---------------------------- PORT B ---------------------------- 
-#define led_off()	            ((LED_PORT &=~ (1 << LED_PIN)),\
+ */
-                                (LED_DIR |= (1 << LED_PIN)))
-
-/* ---------------------------- PORT B ---------------------------- */
 
 #define AVR_PORT                PORTB
 #define AVR_DIR                 DDRB
@@ -85,19 +81,10 @@
 #define snes_irq_off()          (SNES_IRQ_DIR &= ~(1 << SNES_IRQ_PIN))
 #define snes_irq_lo()           (SNES_IRQ_PORT &= ~(1 << SNES_IRQ_PIN))
 
-#define SNES_RESET_PORT           PORTB
-#define SNES_RESET_DIR            DDRB
-#define SNES_RESET_PIN            PB4
 
-
+/*
-#define snes_reset_on()          (SNES_RESET_DIR |= (1 << SNES_RESET_PIN))
+ * ---------------------------- PORT C ---------------------------- 
-#define snes_reset_hi()          (SNES_RESET_PORT |= (1 << SNES_RESET_PIN))
+ */
-
-#define snes_reset_off()          (SNES_RESET_DIR &= ~(1 << SNES_RESET_PIN))
-#define snes_reset_lo()           (SNES_RESET_PORT &= ~(1 << SNES_RESET_PIN))
-
-
-/* ---------------------------- PORT C ---------------------------- */
 
 #define AVR_ADDR_PORT	    	PORTC
 #define AVR_ADDR_DIR	    	DDRC
@@ -105,22 +92,22 @@
 #define AVR_ADDR_LATCH_DIR	    DDRC
 #define AVR_ADDR_LATCH_PIN	    PC6
 
-#define avr_addr_latch_hi()       (AVR_ADDR_LATCH_PORT |= (1 << AVR_ADDR_LATCH_PIN)))
+#define avr_addr_latch_hi()       (AVR_ADDR_LATCH_PORT |= (1 << AVR_ADDR_LATCH_PIN))
-#define avr_addr_latch_lo()       (AVR_ADDR_LATCH_PORT &= ~(1 << AVR_ADDR_LATCH_PIN)))
+#define avr_addr_latch_lo()       (AVR_ADDR_LATCH_PORT &= ~(1 << AVR_ADDR_LATCH_PIN))
 
 #define AVR_ADDR_SCK_PORT	    PORTC
 #define AVR_ADDR_SCK_DIR	    DDRC
 #define AVR_ADDR_SCK_PIN	    PC5
 
-#define avr_addr_sck_hi()       (AVR_ADDR_SCK_PORT |= (1 << AVR_ADDR_SCK_PIN)))
+#define avr_addr_sck_hi()       (AVR_ADDR_SCK_PORT |= (1 << AVR_ADDR_SCK_PIN))
-#define avr_addr_sck_lo()       (AVR_ADDR_SCK_PORT &= ~(1 << AVR_ADDR_SCK_PIN)))
+#define avr_addr_sck_lo()       (AVR_ADDR_SCK_PORT &= ~(1 << AVR_ADDR_SCK_PIN))
 
 #define AVR_ADDR_SER_PORT	    PORTC
 #define AVR_ADDR_SER_DIR	    DDRC
 #define AVR_ADDR_SER_PIN	    PC4
 
-#define avr_addr_ser_hi()       (AVR_ADDR_SER_PORT |= (1 << AVR_ADDR_SER_PIN)))
+#define avr_addr_ser_hi()       (AVR_ADDR_SER_PORT |= (1 << AVR_ADDR_SER_PIN))
-#define avr_addr_ser_lo()       (AVR_ADDR_SER_PORT &= ~(1 << AVR_ADDR_SER_PIN)))
+#define avr_addr_ser_lo()       (AVR_ADDR_SER_PORT &= ~(1 << AVR_ADDR_SER_PIN))
 
 #define AVR_ADDR_LOAD_PORT	    PORTC
 #define AVR_ADDR_LOAD_DIR	    DDRC
@@ -129,12 +116,12 @@
 #define counter_load()	        ((AVR_ADDR_LOAD_PORT &= ~(1 << AVR_ADDR_LOAD_PIN)),\
                                 (AVR_ADDR_LOAD_PORT |= (1 << AVR_ADDR_LOAD_PIN)))
 
-#define AVR_ADDR_DOWN_PORT	    PORTC
+#define AVR_BTLDR_EN_PORT	    PORTC
-#define AVR_ADDR_DOWN_DIR	    DDRC
+#define AVR_BTLDR_EN_DIR	    DDRC
-#define AVR_ADDR_DOWN_PIN	    PC1
+#define AVR_BTLDR_EN_PIN	    PC1
 
-#define counter_down()	        ((AVR_ADDR_DOWN_PORT &= ~(1 << AVR_ADDR_DOWN_PIN)),\
+#define btldr_down()	        ((AVR_BTLDR_EN_PORT &= ~(1 << AVR_BTLDR_EN_PIN)),\
-                                (AVR_ADDR_DOWN_PORT |= (1 << AVR_ADDR_DOWN_PIN)))
+                                (AVR_BTLDR_EN_PORT |= (1 << AVR_BTLDR_EN_PIN)))
 
 #define AVR_ADDR_UP_PORT	    PORTC
 #define AVR_ADDR_UP_DIR	        DDRC
@@ -147,7 +134,21 @@
 #define SNES_WR_DIR	            DDRC
 #define SNES_WR_PIN	            PC3
 
-/* ---------------------------- PORT D ---------------------------- */
+#define LED_PORT	            PORTC
+#define LED_DIR		            DDRC
+#define LED_PIN		            PC7
+
+#define led_on()	            ((LED_PORT &=~ (1 << LED_PIN)),\
+                                (LED_DIR &=~ (1 << LED_PIN)))
+#define led_off()	            ((LED_PORT &=~ (1 << LED_PIN)),\
+                                (LED_DIR |= (1 << LED_PIN)))
+
+#define led_pwm_on()	        (LED_DIR &=~ (1 << LED_PIN))
+#define led_pwm_off()	        (LED_DIR |= (1 << LED_PIN))
+
+/*
+ * ---------------------------- PORT D ---------------------------- 
+ */
 
 #define AVR_SNES_PORT	        PORTD
 #define AVR_SNES_DIR	        DDRD
@@ -160,7 +161,8 @@
                                 (AVR_CS_DIR |= (1 << AVR_CS_PIN)))
 
 #define snes_bus_active()	    ((AVR_SNES_SW_PORT |= (1 << AVR_SNES_SW_PIN)),\
-                                (AVR_CS_DIR &= ~(1 << AVR_CS_PIN)))
+                                (AVR_CS_DIR &= ~(1 << AVR_CS_PIN)),\
+                                (AVR_CS_PORT |= (1 << AVR_CS_PIN)))
 
 #define HI_LOROM_SW_PORT	    PORTD
 #define HI_LOROM_SW_DIR	        DDRD
@@ -177,11 +179,32 @@
 
 #define snes_wr_enable()	    (SNES_WR_EN_PORT |= (1 << SNES_WR_EN_PIN))
 
+#define SNES_RESET_PORT         PORTD
+#define SNES_RESET_DIR          DDRD
+#define SNES_RESET_PIN          PD3
+#define SNES_RESET_INP          PIND
+
+#define snes_reset_on()         (SNES_RESET_DIR |= (1 << SNES_RESET_PIN))
+#define snes_reset_hi()         (SNES_RESET_PORT |= (1 << SNES_RESET_PIN))
+
+#define snes_reset_off()        (SNES_RESET_DIR &= ~(1 << SNES_RESET_PIN))
+#define snes_reset_lo()         (SNES_RESET_PORT &= ~(1 << SNES_RESET_PIN))
+
+#define snes_reset_test()       ((SNES_RESET_INP & (1 << SNES_RESET_PIN)) == 0)
+
+#define MMC_PORT                PORTB
+#define MMC_DIR                 DDRB
+
+#define MMC_MISO_PIN            PB6
+#define MMC_MOSI_PIN            PB5
+#define MMC_SCK_PIN             PB7
+#define MMC_CS_PIN              PB4
 
 
 
 
-void system_init(void);
+
+void sram_init(void);
 void sreg_set(uint32_t addr);
 
 uint8_t sram_read(uint32_t addr);
@@ -191,14 +214,21 @@ void sram_bulk_read_start(uint32_t addr);
 inline void sram_bulk_read_next(void);
 inline void sram_bulk_read_end(void);
 uint8_t sram_bulk_read(void);
+uint16_t sram_read16_be(uint32_t addr);
 
 void sram_bulk_write_start(uint32_t addr);
 inline void sram_bulk_write_next(void);
 inline void sram_bulk_write_end(void);
 void sram_bulk_write(uint8_t data);
 
-void sram_bulk_copy(uint32_t addr, uint8_t * src, uint32_t len);
+void sram_bulk_copy_from_buffer(uint32_t addr, uint8_t * src, uint32_t len);
-void sram_bulk_read_buffer(uint32_t addr, uint8_t * dst, uint32_t len);
+void sram_bulk_copy_into_buffer(uint32_t addr, uint8_t * dst, uint32_t len);
-void sram_bulk_set(uint32_t addr, uint32_t len,uint8_t value);
+
+void sram_bulk_set(uint32_t addr, uint32_t len, uint8_t value);
+
+inline void sram_bulk_addr_save();
+inline void sram_bulk_addr_restore();
+
+
 
 #endif

avr/usbload/system.c

@@ -0,0 +1,192 @@
+/*
+ * =====================================================================================
+ *
+ * ________        .__        __    ________               ____  ________
+ * \_____  \  __ __|__| ____ |  | __\______ \   _______  _/_   |/  _____/
+ *  /  / \  \|  |  \  |/ ___\|  |/ / |    |  \_/ __ \  \/ /|   /   __  \
+ * /   \_/.  \  |  /  \  \___|    <  |    `   \  ___/\   / |   \  |__\  \
+ * \_____\ \_/____/|__|\___  >__|_ \/_______  /\___  >\_/  |___|\_____  /
+ *        \__>             \/     \/        \/     \/                 \/
+ *
+ *                                  www.optixx.org
+ *
+ *
+ *        Version:  1.0
+ *        Created:  07/21/2009 03:32:16 PM
+ *         Author:  david@optixx.org
+ *
+ * =====================================================================================
+ */
+
+
+#include <stdlib.h>
+#include <stdint.h>
+#include <util/delay.h>         /* for _delay_ms() */
+#include <avr/interrupt.h>
+
+
+#include "config.h"
+#include "sram.h"
+#include "system.h"
+#include "uart.h"
+#include "debug.h"
+#include "info.h"
+#include "requests.h"
+#include "irq.h"
+
+system_t my_system;
+
+void system_init(void)
+{
+    snes_reset_hi();
+    snes_reset_off();
+    my_system.reset_line = RESET_OFF;
+
+    snes_irq_hi();
+    snes_irq_off();
+    my_system.irq_line = IRQ_OFF;
+
+
+    snes_wr_disable();
+    my_system.wr_line = WR_DISABLE;
+
+    avr_bus_active();
+    my_system.bus_mode = MODE_AVR;
+
+    snes_lorom();
+    my_system.rom_mode = LOROM;
+
+    my_system.snes_reset_count = 0;
+    my_system.avr_reset_count = 0;
+
+    my_system.reset_irq = RESET_IRQ_OFF;
+
+}
+
+void system_send_snes_reset()
+{
+    info_P(PSTR("Reset SNES\n"));
+    cli();
+    snes_reset_on();
+    snes_reset_lo();
+    _delay_ms(2);
+    snes_reset_hi();
+    snes_reset_off();
+    sei();
+    my_system.snes_reset_count++;
+}
+
+void system_send_snes_irq()
+{
+    snes_irq_on();
+    snes_irq_lo();
+    _delay_us(20);
+    snes_irq_hi();
+    snes_irq_off();
+}
+
+void system_snes_irq_off()
+{
+    snes_irq_off();
+    my_system.irq_line = IRQ_OFF;
+}
+
+void system_snes_irq_on()
+{
+    snes_irq_on();
+    my_system.irq_line = IRQ_ON;
+}
+
+
+void system_set_bus_avr()
+{
+    avr_bus_active();
+    info_P(PSTR("Activate AVR bus\n"));
+    my_system.bus_mode = MODE_AVR;
+}
+
+void system_set_wr_disable()
+{
+    snes_wr_disable();
+    my_system.wr_line = WR_DISABLE;
+    info_P(PSTR("Disable SNES WR\n"));
+}
+
+void system_set_wr_enable()
+{
+    snes_wr_enable();
+    my_system.wr_line = WR_ENABLE;
+    info_P(PSTR("Enable SNES WR\n"));
+}
+
+void system_set_bus_snes()
+{
+    snes_bus_active();
+    my_system.bus_mode = MODE_SNES;
+    info_P(PSTR("Activate SNES bus\n"));
+}
+
+void system_set_rom_mode(usb_transaction_t * usb_trans)
+{
+    if (usb_trans->req_bank_size == 0x8000) {
+        snes_lorom();
+        my_system.rom_mode = LOROM;
+        info_P(PSTR("Set SNES lorom \n"));
+    } else {
+        snes_hirom();
+        my_system.rom_mode = HIROM;
+        info_P(PSTR("Set SNES hirom \n"));
+    }
+}
+
+void system_set_rom_lorom()
+{
+    snes_lorom();
+    my_system.rom_mode = LOROM;
+    info_P(PSTR("Set SNES lorom \n"));
+}
+
+
+void system_set_rom_hirom()
+{
+    snes_hirom();
+    my_system.rom_mode = HIROM;
+    info_P(PSTR("Set SNES hirom \n"));
+}
+
+char *system_status_helper(uint8_t val)
+{
+    if (val)
+        return "ON";
+    else
+        return "OFF";
+}
+
+char *system_status_bus(uint8_t val)
+{
+    if (val)
+        return "SNES";
+    else
+        return "AVR";
+}
+
+char *system_status_rom(uint8_t val)
+{
+    if (val)
+        return "HIROM";
+    else
+        return "LOROM";
+}
+
+void system_status()
+{
+    info_P(PSTR("\nBus Mode       %s\n"), system_status_bus(my_system.bus_mode));
+    info_P(PSTR("Rom Mode       %s\n"), system_status_rom(my_system.rom_mode));
+    info_P(PSTR("Reset Line     %s\n"),
+           system_status_helper(my_system.reset_line));
+    info_P(PSTR("IRQ Line       %s\n"), system_status_helper(my_system.irq_line));
+    info_P(PSTR("WR Line        %s\n"), system_status_helper(my_system.wr_line));
+    info_P(PSTR("Reset IRQ      %s\n"), system_status_helper(my_system.reset_irq));
+    info_P(PSTR("SNES Reset     0x%02x\n"), my_system.snes_reset_count);
+    info_P(PSTR("AVR Reset      0x%02x\n"), my_system.avr_reset_count);
+}

avr/usbload/system.h

@@ -0,0 +1,57 @@
+/*
+ * =====================================================================================
+ *
+ * ________        .__        __    ________               ____  ________
+ * \_____  \  __ __|__| ____ |  | __\______ \   _______  _/_   |/  _____/
+ *  /  / \  \|  |  \  |/ ___\|  |/ / |    |  \_/ __ \  \/ /|   /   __  \
+ * /   \_/.  \  |  /  \  \___|    <  |    `   \  ___/\   / |   \  |__\  \
+ * \_____\ \_/____/|__|\___  >__|_ \/_______  /\___  >\_/  |___|\_____  /
+ *        \__>             \/     \/        \/     \/                 \/
+ *
+ *                                  www.optixx.org
+ *
+ *
+ *        Version:  1.0
+ *        Created:  07/21/2009 03:32:16 PM
+ *         Author:  david@optixx.org
+ *
+ * =====================================================================================
+ */
+
+
+
+#ifndef __SYSTEM_H__
+#define __SYSTEM_H__
+
+#include "requests.h"
+
+
+
+typedef struct system_t {
+    enum bus_mode_e { MODE_AVR, MODE_SNES } bus_mode;
+    enum rom_mode_e { LOROM, HIROM } rom_mode;
+    enum reset_line_e { RESET_OFF, RESET_ON } reset_line;
+    enum irq_line_e { IRQ_ON, IRQ_OFF } irq_line;
+    enum wr_line_e { WR_DISABLE, WR_ENABLE } wr_line;
+    enum reset_irq_e { RESET_IRQ_OFF, RESET_IRQ_ON } reset_irq;
+
+    uint8_t snes_reset_count;
+    uint8_t avr_reset_count;
+} system_t;
+
+void system_init(void);
+void system_init(void);
+void system_send_snes_reset(void);
+void system_send_snes_irq(void);
+void system_set_bus_avr(void);
+void system_set_bus_snes(void);
+void system_set_rom_mode(usb_transaction_t * usb_trans);
+void system_set_rom_hirom(void);
+void system_set_rom_lorom(void);
+void system_snes_irq_off(void);
+void system_set_wr_disable(void);
+void system_set_wr_enable(void);
+
+void system_status();
+
+#endif

avr/usbload/tags

@@ -0,0 +1,428 @@
+!_TAG_FILE_FORMAT	2	/extended format; --format=1 will not append ;" to lines/
+!_TAG_FILE_SORTED	1	/0=unsorted, 1=sorted, 2=foldcase/
+!_TAG_PROGRAM_AUTHOR	Darren Hiebert	/dhiebert@users.sourceforge.net/
+!_TAG_PROGRAM_NAME	Exuberant Ctags	//
+!_TAG_PROGRAM_URL	http://ctags.sourceforge.net	/official site/
+!_TAG_PROGRAM_VERSION	5.7	//
+AVR_ADDR_DIR	sram.h	103;"	d
+AVR_ADDR_DOWN_DIR	sram.h	133;"	d
+AVR_ADDR_DOWN_PIN	sram.h	134;"	d
+AVR_ADDR_DOWN_PORT	sram.h	132;"	d
+AVR_ADDR_LATCH_DIR	sram.h	105;"	d
+AVR_ADDR_LATCH_PIN	sram.h	106;"	d
+AVR_ADDR_LATCH_PORT	sram.h	104;"	d
+AVR_ADDR_LOAD_DIR	sram.h	126;"	d
+AVR_ADDR_LOAD_PIN	sram.h	127;"	d
+AVR_ADDR_LOAD_PORT	sram.h	125;"	d
+AVR_ADDR_PORT	sram.h	102;"	d
+AVR_ADDR_SCK_DIR	sram.h	112;"	d
+AVR_ADDR_SCK_PIN	sram.h	113;"	d
+AVR_ADDR_SCK_PORT	sram.h	111;"	d
+AVR_ADDR_SER_DIR	sram.h	119;"	d
+AVR_ADDR_SER_PIN	sram.h	120;"	d
+AVR_ADDR_SER_PORT	sram.h	118;"	d
+AVR_ADDR_UP_DIR	sram.h	140;"	d
+AVR_ADDR_UP_PIN	sram.h	141;"	d
+AVR_ADDR_UP_PORT	sram.h	139;"	d
+AVR_CS_DIR	sram.h	71;"	d
+AVR_CS_PIN	sram.h	72;"	d
+AVR_CS_PORT	sram.h	70;"	d
+AVR_DATA_DIR	sram.h	35;"	d
+AVR_DATA_PIN	sram.h	36;"	d
+AVR_DATA_PORT	sram.h	34;"	d
+AVR_DIR	sram.h	55;"	d
+AVR_PORT	sram.h	54;"	d
+AVR_RD_DIR	sram.h	57;"	d
+AVR_RD_PIN	sram.h	58;"	d
+AVR_RD_PORT	sram.h	56;"	d
+AVR_SNES_DIR	sram.h	153;"	d
+AVR_SNES_PORT	sram.h	152;"	d
+AVR_SNES_SW_DIR	sram.h	155;"	d
+AVR_SNES_SW_PIN	sram.h	156;"	d
+AVR_SNES_SW_PORT	sram.h	154;"	d
+AVR_WR_DIR	sram.h	64;"	d
+AVR_WR_PIN	sram.h	65;"	d
+AVR_WR_PORT	sram.h	63;"	d
+CR	uart.h	25;"	d
+DEBOUNCE	timer.c	44;"	d	file:
+DEBUG	config.h	25;"	d
+DEBUG_CRC	config.h	31;"	d
+DEBUG_SHM	config.h	32;"	d
+DEBUG_SRAM	config.h	28;"	d
+DEBUG_SRAM_RAW	config.h	29;"	d
+DEBUG_SREG	config.h	30;"	d
+DEBUG_USB	config.h	26;"	d
+DEBUG_USB_TRANS	config.h	27;"	d
+FILE_MKDIR	config.h	48;"	d
+FILE_RM	config.h	49;"	d
+FILE_WRITE	config.h	47;"	d
+Fat	fat.h	/^  extern struct Fat{						\/\/ fat daten (1.cluster, root-dir, dir usw.)$/;"	s
+File	fat.h	/^  extern struct File{					\/\/ datei infos$/;"	s
+HI_LOROM_SW_DIR	sram.h	166;"	d
+HI_LOROM_SW_PIN	sram.h	167;"	d
+HI_LOROM_SW_PORT	sram.h	165;"	d
+INBYTE	rle.c	44;"	d	file:
+ISR	timer.c	/^ISR (SIG_OUTPUT_COMPARE1A)$/;"	f
+ISR	uart.c	/^ISR(USART0_RX_vect)$/;"	f
+LED_DIR	sram.h	44;"	d
+LED_PIN	sram.h	45;"	d
+LED_PORT	sram.h	43;"	d
+MAX_CLUSTERS_IN_ROW	fat.h	11;"	d
+MMC_CLK	mmc.h	21;"	d
+MMC_CS	mmc.h	18;"	d
+MMC_DI	mmc.h	20;"	d
+MMC_DO	mmc.h	19;"	d
+MMC_READ	mmc.h	15;"	d
+MMC_READ	mmc.h	24;"	d
+MMC_REG	mmc.h	16;"	d
+MMC_REG	mmc.h	25;"	d
+MMC_WRITE	mmc.h	14;"	d
+MMC_WRITE	mmc.h	23;"	d
+OCR1A	timer.c	34;"	d	file:
+OUTBYTE	rle.c	54;"	d	file:
+OVER_WRITE	fat.h	10;"	d
+PROGMEM	loader.c	/^const char _rom[ROM_BUFFER_SIZE] PROGMEM = {$/;"	v
+REQ_STATUS_AVR	config.h	40;"	d
+REQ_STATUS_BULK_NEXT	config.h	37;"	d
+REQ_STATUS_BULK_UPLOAD	config.h	36;"	d
+REQ_STATUS_CRC	config.h	38;"	d
+REQ_STATUS_IDLE	config.h	34;"	d
+REQ_STATUS_SNES	config.h	39;"	d
+REQ_STATUS_UPLOAD	config.h	35;"	d
+ROM_BUFFER_SIZE	loader.h	5;"	d
+ROM_HUFFMAN_SIZE	loader.h	6;"	d
+ROM_RLE_SIZE	loader.h	7;"	d
+RUNCHAR	rle.c	33;"	d	file:
+SHARED_IRQ_HANDLER_HI	shared_memory.h	59;"	d
+SHARED_IRQ_HANDLER_LO	shared_memory.h	58;"	d
+SHARED_IRQ_LOC_HI	shared_memory.h	55;"	d
+SHARED_IRQ_LOC_LO	shared_memory.h	54;"	d
+SHARED_MEM_RX_AVR_ACK	shared_memory.h	43;"	d
+SHARED_MEM_RX_AVR_RTS	shared_memory.h	44;"	d
+SHARED_MEM_RX_CMD_FILESEL	shared_memory.h	47;"	d
+SHARED_MEM_RX_CMD_PRINFT	shared_memory.h	46;"	d
+SHARED_MEM_RX_LOC_CMD	shared_memory.h	50;"	d
+SHARED_MEM_RX_LOC_LEN	shared_memory.h	51;"	d
+SHARED_MEM_RX_LOC_PAYLOAD	shared_memory.h	52;"	d
+SHARED_MEM_RX_LOC_STATE	shared_memory.h	49;"	d
+SHARED_MEM_SWITCH_DELAY	shared_memory.h	26;"	d
+SHARED_MEM_SWITCH_IRQ	shared_memory.h	25;"	d
+SHARED_MEM_TX_CMD_BANK_COUNT	shared_memory.h	31;"	d
+SHARED_MEM_TX_CMD_BANK_CURRENT	shared_memory.h	32;"	d
+SHARED_MEM_TX_CMD_TERMINATE	shared_memory.h	37;"	d
+SHARED_MEM_TX_CMD_UPLOAD_END	shared_memory.h	35;"	d
+SHARED_MEM_TX_CMD_UPLOAD_PROGESS	shared_memory.h	36;"	d
+SHARED_MEM_TX_CMD_UPLOAD_START	shared_memory.h	34;"	d
+SHARED_MEM_TX_LOC_CMD	shared_memory.h	40;"	d
+SHARED_MEM_TX_LOC_PAYLOAD	shared_memory.h	41;"	d
+SHARED_MEM_TX_LOC_STATE	shared_memory.h	39;"	d
+SHARED_MEM_TX_SNES_ACK	shared_memory.h	28;"	d
+SHARED_MEM_TX_SNES_RTS	shared_memory.h	29;"	d
+SMALL_FILE_SYSTEM	config.h	50;"	d
+SMALL_FILE_SYSTEM	fat.h	8;"	d
+SNES_IRQ_DIR	sram.h	78;"	d
+SNES_IRQ_PIN	sram.h	79;"	d
+SNES_IRQ_PORT	sram.h	77;"	d
+SNES_RESET_DIR	sram.h	89;"	d
+SNES_RESET_PIN	sram.h	90;"	d
+SNES_RESET_PORT	sram.h	88;"	d
+SNES_WR_DIR	sram.h	147;"	d
+SNES_WR_EN_DIR	sram.h	173;"	d
+SNES_WR_EN_PIN	sram.h	174;"	d
+SNES_WR_EN_PORT	sram.h	172;"	d
+SNES_WR_PIN	sram.h	148;"	d
+SNES_WR_PORT	sram.h	146;"	d
+SPI_Mode	mmc.h	12;"	d
+TRANSFER_BUFFER_SIZE	config.h	45;"	d
+USB_AVR_RESET	requests.h	40;"	d
+USB_BULK_UPLOAD_ADDR	requests.h	35;"	d
+USB_BULK_UPLOAD_END	requests.h	37;"	d
+USB_BULK_UPLOAD_INIT	requests.h	34;"	d
+USB_BULK_UPLOAD_NEXT	requests.h	36;"	d
+USB_CFG_CHECK_CRC	usbconfig.h	72;"	d
+USB_CFG_CHECK_DATA_TOGGLING	usbconfig.h	211;"	d
+USB_CFG_CLOCK_KHZ	usbconfig.h	65;"	d
+USB_CFG_DESCR_PROPS_CONFIGURATION	usbconfig.h	346;"	d
+USB_CFG_DESCR_PROPS_DEVICE	usbconfig.h	345;"	d
+USB_CFG_DESCR_PROPS_HID	usbconfig.h	352;"	d
+USB_CFG_DESCR_PROPS_HID_REPORT	usbconfig.h	353;"	d
+USB_CFG_DESCR_PROPS_STRINGS	usbconfig.h	347;"	d
+USB_CFG_DESCR_PROPS_STRING_0	usbconfig.h	348;"	d
+USB_CFG_DESCR_PROPS_STRING_PRODUCT	usbconfig.h	350;"	d
+USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER	usbconfig.h	351;"	d
+USB_CFG_DESCR_PROPS_STRING_VENDOR	usbconfig.h	349;"	d
+USB_CFG_DESCR_PROPS_UNKNOWN	usbconfig.h	354;"	d
+USB_CFG_DEVICE_CLASS	usbconfig.h	266;"	d
+USB_CFG_DEVICE_ID	usbconfig.h	231;"	d
+USB_CFG_DEVICE_NAME	usbconfig.h	251;"	d
+USB_CFG_DEVICE_NAME_LEN	usbconfig.h	252;"	d
+USB_CFG_DEVICE_SUBCLASS	usbconfig.h	267;"	d
+USB_CFG_DEVICE_VERSION	usbconfig.h	238;"	d
+USB_CFG_DMINUS_BIT	usbconfig.h	52;"	d
+USB_CFG_DPLUS_BIT	usbconfig.h	56;"	d
+USB_CFG_EP3_NUMBER	usbconfig.h	106;"	d
+USB_CFG_HAVE_FLOWCONTROL	usbconfig.h	161;"	d
+USB_CFG_HAVE_INTRIN_ENDPOINT	usbconfig.h	95;"	d
+USB_CFG_HAVE_INTRIN_ENDPOINT3	usbconfig.h	100;"	d
+USB_CFG_HAVE_MEASURE_FRAME_LENGTH	usbconfig.h	219;"	d
+USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH	usbconfig.h	279;"	d
+USB_CFG_IMPLEMENT_FN_READ	usbconfig.h	149;"	d
+USB_CFG_IMPLEMENT_FN_WRITE	usbconfig.h	144;"	d
+USB_CFG_IMPLEMENT_FN_WRITEOUT	usbconfig.h	155;"	d
+USB_CFG_IMPLEMENT_HALT	usbconfig.h	116;"	d
+USB_CFG_INTERFACE_CLASS	usbconfig.h	271;"	d
+USB_CFG_INTERFACE_PROTOCOL	usbconfig.h	273;"	d
+USB_CFG_INTERFACE_SUBCLASS	usbconfig.h	272;"	d
+USB_CFG_INTR_POLL_INTERVAL	usbconfig.h	130;"	d
+USB_CFG_IOPORTNAME	usbconfig.h	48;"	d
+USB_CFG_IS_SELF_POWERED	usbconfig.h	135;"	d
+USB_CFG_LONG_TRANSFERS	usbconfig.h	166;"	d
+USB_CFG_MAX_BUS_POWER	usbconfig.h	139;"	d
+USB_CFG_SUPPRESS_INTR_CODE	usbconfig.h	122;"	d
+USB_CFG_VENDOR_ID	usbconfig.h	226;"	d
+USB_CFG_VENDOR_NAME	usbconfig.h	241;"	d
+USB_CFG_VENDOR_NAME_LEN	usbconfig.h	242;"	d
+USB_COUNT_SOF	usbconfig.h	187;"	d
+USB_CRC	requests.h	31;"	d
+USB_CRC_ADDR	requests.h	32;"	d
+USB_CRC_CHECK	config.h	43;"	d
+USB_DOWNLOAD_ADDR	requests.h	29;"	d
+USB_DOWNLOAD_INIT	requests.h	28;"	d
+USB_MAX_TRANS	config.h	42;"	d
+USB_MODE_AVR	requests.h	39;"	d
+USB_MODE_SNES	requests.h	38;"	d
+USB_UPLOAD_ADDR	requests.h	26;"	d
+USB_UPLOAD_INIT	requests.h	25;"	d
+WGM12	timer.c	38;"	d	file:
+WRITE	fat.h	9;"	d
+XTAL	timer.c	42;"	d	file:
+_FAT_H	fat.h	4;"	d
+_FILE_H	file.h	6;"	d
+_HARDWARE_H	hardware.h	7;"	d
+_MMC_H	mmc.h	9;"	d
+__COMMAND_H__	command.h	23;"	d
+__CONFIH_H__	config.h	22;"	d
+__CRC_H__	crc.h	23;"	d
+__DEBUG_H__	debug.h	24;"	d
+__DUMP_H__	dump.h	23;"	d
+__FIFO_H__	fifo.h	21;"	d
+__FIFO_H__	loader.h	3;"	d
+__INFO_H__	info.h	24;"	d
+__REQUESTS_H__	requests.h	23;"	d
+__RLE_H__	rle.h	22;"	d
+__SHARED_MEMORY_H__	shared_memory.h	22;"	d
+__SRAM_H__	sram.h	24;"	d
+__TESTING_H__	testing.h	23;"	d
+__TIMER_H__	timer.h	22;"	d
+__UART_H__	uart.h	23;"	d
+__USB_BULK_H__	usb_bulk.h	23;"	d
+__WATCHDOG_H__	watchdog.h	27;"	d
+__usbconfig_h_included__	usbconfig.h	34;"	d
+_inline_fifo_get	fifo.h	/^static inline uint8_t _inline_fifo_get(fifo_t * f)$/;"	f
+_inline_fifo_put	fifo.h	/^static inline uint8_t _inline_fifo_put(fifo_t * f, const uint8_t data)$/;"	f
+adc_int	uart.c	/^    uint8_t adc_int:1;$/;"	m	struct:__anon2	file:
+addr	main.c	/^uint32_t addr;$/;"	v
+addr_current	sram.c	/^uint32_t addr_current = 0;$/;"	v
+addr_stash	sram.c	/^uint32_t addr_stash = 0;$/;"	v
+attrib	fat.h	/^	unsigned char 		attrib;			\/\/ 11,1			datei Attribut: 8=value name, 32=datei, 16=Verzeichniss, 15=linux kleingeschrieben eintrag$/;"	m	struct:File
+avr_addr_latch_hi	sram.h	108;"	d
+avr_addr_latch_lo	sram.h	109;"	d
+avr_addr_sck_hi	sram.h	115;"	d
+avr_addr_sck_lo	sram.h	116;"	d
+avr_addr_ser_hi	sram.h	122;"	d
+avr_addr_ser_lo	sram.h	123;"	d
+avr_bus_active	sram.h	158;"	d
+avr_cs_hi	sram.h	74;"	d
+avr_cs_lo	sram.h	75;"	d
+avr_data_in	sram.h	38;"	d
+avr_data_out	sram.h	41;"	d
+avr_rd_hi	sram.h	60;"	d
+avr_rd_lo	sram.h	61;"	d
+avr_wr_hi	sram.h	67;"	d
+avr_wr_lo	sram.h	68;"	d
+boot_startup_rom	main.c	/^void boot_startup_rom()$/;"	f
+bufferDirty	fat.h	/^	unsigned char 		bufferDirty;	\/\/ puffer wurde beschrieben, sector muss geschrieben werden bevor er neu geladen wird$/;"	m	struct:Fat
+cntOfBytes	fat.h	/^	unsigned int 			cntOfBytes;		\/\/ -nicht direkt aus dem dateisystem- zäht geschriebene bytes eines sektors$/;"	m	struct:File
+count	fifo.h	/^    uint8_t volatile count;     \/\/ # Zeichen im Puffer$/;"	m	struct:__anon1
+counter_down	sram.h	136;"	d
+counter_load	sram.h	129;"	d
+counter_up	sram.h	143;"	d
+crc	main.c	/^uint16_t crc = 0;$/;"	v
+crc_check_bulk_memory	crc.c	/^uint16_t crc_check_bulk_memory(uint32_t bottom_addr, uint32_t top_addr, uint32_t bank_size)$/;"	f
+crc_check_memory_range	crc.c	/^uint16_t crc_check_memory_range(uint32_t start_addr, uint32_t size,uint8_t *buffer)$/;"	f
+crc_xmodem_update	crc.c	/^uint16_t crc_xmodem_update(uint16_t crc, uint8_t data)$/;"	f
+currentSectorNr	fat.h	/^	unsigned long int 	currentSectorNr;\/\/ aktuell geladener Sektor (in sector)  \/\/beschleunigt wenn z.b 2* 512 byte puffer vorhanden, oder bei fat operationen im gleichen sektor$/;"	m	struct:Fat
+dataDirSec	fat.h	/^	unsigned long int  	dataDirSec;		\/\/ Sektor nr data area $/;"	m	struct:Fat
+data_buffer	main.c	/^uint8_t data_buffer[4];$/;"	v
+debug	debug.c	/^void debug(int level, char* format, ...) {$/;"	f
+debug	debug.h	34;"	d
+debug_level	main.c	/^uint8_t debug_level = (DEBUG | DEBUG_USB | DEBUG_CRC);$/;"	v
+dir	fat.h	/^	unsigned long int 	dir; 		  	\/\/ Direktory zeiger rootDir=='0' sonst(1.Cluster des dir; start auf root)$/;"	m	struct:Fat
+do_crc	crc.c	/^uint16_t do_crc(uint8_t * data, uint16_t size)$/;"	f
+do_crc_update	crc.c	/^uint16_t do_crc_update(uint16_t crc, uint8_t * data, uint16_t size)$/;"	f
+dump_memory	dump.c	/^void dump_memory(uint32_t bottom_addr, uint32_t top_addr)$/;"	f
+dump_packet	dump.c	/^void dump_packet(uint32_t addr, uint32_t len, uint8_t * packet)$/;"	f
+endSectors	fat.h	/^	unsigned long int 	endSectors;	$/;"	m	struct:Fat
+fat	fat.c	/^struct Fat fat;   					\/\/ wichtige daten\/variablen der fat$/;"	v	typeref:struct:Fat
+fatSec	fat.h	/^	unsigned long int  	fatSec;	 		\/\/ Sektor nr fat area$/;"	m	struct:Fat
+fatType	fat.h	/^	unsigned char  		fatType;		\/\/ fat16 oder fat32 (16 oder 32)$/;"	m	struct:Fat
+fat_cd	fat.c	/^unsigned char fat_cd(char name[]){$/;"	f
+fat_clustToSec	fat.c	/^unsigned long int fat_clustToSec(unsigned long int clust){$/;"	f
+fat_delClusterChain	fat.c	/^void fat_delClusterChain(unsigned long int startCluster){$/;"	f
+fat_getFatChainClustersInRow	fat.c	/^void fat_getFatChainClustersInRow(unsigned long int offsetCluster){$/;"	f
+fat_getFreeClustersInRow	fat.c	/^void fat_getFreeClustersInRow(unsigned long int offsetCluster){$/;"	f
+fat_getFreeRowOfCluster	fat.c	/^unsigned char fat_getFreeRowOfCluster(unsigned long secStart){$/;"	f
+fat_getFreeRowOfDir	fat.c	/^void fat_getFreeRowOfDir(unsigned long int dir){$/;"	f
+fat_getNextCluster	fat.c	/^unsigned long int fat_getNextCluster(unsigned long int oneCluster){	$/;"	f
+fat_initfat	fat.c	/^unsigned char fat_initfat(void){					$/;"	f
+fat_loadFatData	fat.c	/^unsigned char fat_loadFatData(unsigned long int sec){$/;"	f
+fat_loadFileDataFromCluster	fat.c	/^unsigned char fat_loadFileDataFromCluster(unsigned long int sec , char name[]){$/;"	f
+fat_loadFileDataFromDir	fat.c	/^unsigned char fat_loadFileDataFromDir(char name[]){ $/;"	f
+fat_loadRowOfSector	fat.c	/^unsigned char fat_loadRowOfSector(unsigned int row){$/;"	f
+fat_loadSector	fat.c	/^unsigned char fat_loadSector(unsigned long int sec){$/;"	f
+fat_makeFileEntry	fat.c	/^void fat_makeFileEntry(char name[],unsigned char attrib,unsigned long int length){$/;"	f
+fat_makeRowDataEntry	fat.c	/^void fat_makeRowDataEntry(unsigned int row,char name[],unsigned char attrib,unsigned long int cluster,unsigned long int length){$/;"	f
+fat_secToClust	fat.c	/^unsigned long int fat_secToClust(unsigned long int sec){$/;"	f
+fat_setCluster	fat.c	/^void fat_setCluster(unsigned long int cluster, unsigned long int content){  $/;"	f
+fat_setClusterChain	fat.c	/^void fat_setClusterChain(unsigned long int startCluster,unsigned int endCluster){$/;"	f
+fat_str	fat.c	/^char * fat_str(char *str){$/;"	f
+fat_writeSector	fat.c	/^unsigned char fat_writeSector(unsigned long int sec){	$/;"	f
+ffcd	file.c	/^unsigned char ffcd(char name[]){		$/;"	f
+ffcdLower	file.c	/^unsigned char ffcdLower(void){$/;"	f
+ffclose	file.c	/^unsigned char ffclose(void){$/;"	f
+ffls	file.c	/^void ffls(void){$/;"	f
+ffmkdir	file.c	/^void ffmkdir(char name[]){$/;"	f
+ffopen	file.c	/^unsigned char ffopen(char name[]){		$/;"	f
+ffread	file.c	/^inline unsigned char ffread(void){  	 $/;"	f
+ffrm	file.c	/^unsigned char ffrm(char name[]){ $/;"	f
+ffseek	file.c	/^void ffseek(unsigned long int offset){	$/;"	f
+ffwrite	file.c	/^inline void ffwrite(unsigned char c){$/;"	f
+ffwrites	file.c	/^inline void ffwrites(const char *s ){$/;"	f
+fifo_get_nowait	fifo.c	/^int fifo_get_nowait(fifo_t * f)$/;"	f
+fifo_get_wait	fifo.c	/^uint8_t fifo_get_wait(fifo_t * f)$/;"	f
+fifo_init	fifo.c	/^void fifo_init(fifo_t * f, uint8_t * buffer, const uint8_t size)$/;"	f
+fifo_put	fifo.c	/^uint8_t fifo_put(fifo_t * f, const uint8_t data)$/;"	f
+fifo_t	fifo.h	/^} fifo_t;$/;"	t	typeref:struct:__anon1
+file	fat.c	/^struct File file;					\/\/ wichtige dateibezogene daten\/variablen$/;"	v	typeref:struct:File
+fileUpdate	file.c	/^void fileUpdate(void){$/;"	f
+firstCluster	fat.h	/^	unsigned long int 	firstCluster;	\/\/ 20,2 \/26,2	datei 1.cluster hi,low(möglicherweise der einzige)	(4-byte)$/;"	m	struct:File
+info	info.c	/^void info(char* format, ...) {$/;"	f
+info	info.c	34;"	d	file:
+info	info.h	34;"	d
+intflags	uart.c	/^} intflags;$/;"	v	typeref:struct:__anon2
+irq_addr_hi	shared_memory.c	/^uint8_t irq_addr_hi;$/;"	v
+irq_addr_lo	shared_memory.c	/^uint8_t irq_addr_lo;$/;"	v
+lastCluster	fat.h	/^	unsigned long int 	lastCluster;	\/\/ -nicht direkt aus dem dateisystem- letzter cluster der ersten kette$/;"	m	struct:File
+led_off	sram.h	49;"	d
+led_on	sram.h	47;"	d
+length	fat.h	/^	unsigned long int 	length;			\/\/ 28,4			datei Länge (4-byte)$/;"	m	struct:File
+lsRowsOfClust	file.c	/^void lsRowsOfClust (unsigned long int start_sec){$/;"	f
+main	main.c	/^int main(void)$/;"	f
+mmc_disable	mmc.h	38;"	d
+mmc_enable	mmc.h	40;"	d
+mmc_init	mmc.c	/^uint8_t mmc_init()$/;"	f
+mmc_read_block	mmc.c	/^void mmc_read_block(uint8_t * cmd, uint8_t * Buffer, uint16_t Bytes)$/;"	f
+mmc_read_byte	mmc.c	/^uint8_t mmc_read_byte(void)$/;"	f
+mmc_read_cid	mmc.c	/^uint8_t mmc_read_cid(uint8_t * Buffer)$/;"	f
+mmc_read_csd	mmc.c	/^uint8_t mmc_read_csd(uint8_t * Buffer)$/;"	f
+mmc_read_sector	mmc.c	/^uint8_t mmc_read_sector(uint32_t addr, uint8_t * Buffer)$/;"	f
+mmc_write_byte	mmc.c	/^void mmc_write_byte(uint8_t Byte)$/;"	f
+mmc_write_command	mmc.c	/^uint8_t mmc_write_command(uint8_t * cmd)$/;"	f
+mmc_write_sector	mmc.c	/^uint8_t mmc_write_sector(uint32_t addr, uint8_t * Buffer)$/;"	f
+name	fat.h	/^	unsigned char 		name[13];		\/\/ 0,10			datei Name.ext (8.3 = max 11)(MUSS unsigned char weil E5)$/;"	m	struct:File
+nop	mmc.h	42;"	d
+pread	fifo.h	/^    uint8_t *pread;             \/\/ Lesezeiger$/;"	m	struct:__anon1
+prescaler	timer.c	/^uint16_t prescaler;$/;"	v
+pwrite	fifo.h	/^    uint8_t *pwrite;            \/\/ Schreibzeiger$/;"	m	struct:__anon1
+read2end	fifo.h	/^    uint8_t read2end, write2end;        \/\/ # Zeichen bis zum Überlauf Lese-\/Schreibzeiger$/;"	m	struct:__anon1
+read_buffer	main.c	/^uint8_t read_buffer[TRANSFER_BUFFER_SIZE];$/;"	v
+req_addr	main.c	/^uint32_t req_addr = 0;$/;"	v
+req_addr_end	main.c	/^uint32_t req_addr_end = 0;$/;"	v
+req_bank	main.c	/^uint8_t req_bank;$/;"	v
+req_bank_cnt	main.c	/^uint16_t req_bank_cnt;$/;"	v
+req_bank_size	main.c	/^uint32_t req_bank_size;$/;"	v
+req_percent	main.c	/^uint8_t req_percent;$/;"	v
+req_percent_last	main.c	/^uint8_t req_percent_last;$/;"	v
+req_size	main.c	/^uint32_t req_size;$/;"	v
+req_state	main.c	/^uint8_t req_state = REQ_STATUS_IDLE;$/;"	v
+rle_decode	rle.c	/^uint8_t rle_decode(PGM_VOID_P in_addr, int32_t in_len, uint32_t out_addr)$/;"	f
+rootDir	fat.h	/^	unsigned long int  	rootDir;		\/\/ Sektor(f16)\/Cluster(f32) nr root directory$/;"	m	struct:Fat
+row	fat.h	/^	unsigned char 		row;			\/\/ reihe im sektor in der die datei infos stehen (reihe 0-15)$/;"	m	struct:File
+rx_int	uart.c	/^    uint8_t rx_int:1;$/;"	m	struct:__anon2	file:
+rx_remaining	main.c	/^uint8_t rx_remaining = 0;$/;"	v
+rxbuff	uart.c	/^volatile char rxbuff;$/;"	v
+scratchpad_cmd	shared_memory.c	/^uint8_t scratchpad_cmd;$/;"	v
+scratchpad_payload	shared_memory.c	/^uint8_t scratchpad_payload;$/;"	v
+scratchpad_state	shared_memory.c	/^uint8_t scratchpad_state;$/;"	v
+secPerClust	fat.h	/^	unsigned char 		secPerClust;	\/\/ anzahl der sektoren pro cluster$/;"	m	struct:Fat
+second	timer.c	/^uint16_t volatile second;          \/\/ count seconds$/;"	v
+sector	fat.h	/^	unsigned char 		sector[512];	\/\/ der puffer für sektoren !$/;"	m	struct:Fat
+seek	fat.h	/^	unsigned long int 	seek;			\/\/ schreib position in der datei$/;"	m	struct:File
+send_irq	command.c	/^void send_irq()$/;"	f
+send_reset	command.c	/^void send_reset()$/;"	f
+set_rom_mode	command.c	/^void set_rom_mode()$/;"	f
+shared_memory_irq_hook	shared_memory.c	/^void shared_memory_irq_hook()$/;"	f
+shared_memory_irq_restore	shared_memory.c	/^void shared_memory_irq_restore()$/;"	f
+shared_memory_read	shared_memory.c	/^int shared_memory_read(uint8_t *cmd, uint8_t *len,uint8_t *buffer)$/;"	f
+shared_memory_scratchpad_tx_restore	shared_memory.c	/^void shared_memory_scratchpad_tx_restore()$/;"	f
+shared_memory_scratchpad_tx_save	shared_memory.c	/^void shared_memory_scratchpad_tx_save()$/;"	f
+shared_memory_write	shared_memory.c	/^void shared_memory_write(uint8_t cmd, uint8_t value)$/;"	f
+shared_memory_yield	shared_memory.c	/^void shared_memory_yield()$/;"	f
+size	fifo.h	/^    uint8_t size;               \/\/ Puffer-Größe$/;"	m	struct:__anon1
+snes_bus_active	sram.h	162;"	d
+snes_hirom	sram.h	169;"	d
+snes_irq_hi	sram.h	83;"	d
+snes_irq_lo	sram.h	86;"	d
+snes_irq_off	sram.h	85;"	d
+snes_irq_on	sram.h	82;"	d
+snes_lorom	sram.h	170;"	d
+snes_reset_hi	sram.h	94;"	d
+snes_reset_lo	sram.h	97;"	d
+snes_reset_off	sram.h	96;"	d
+snes_reset_on	sram.h	93;"	d
+snes_wr_disable	sram.h	176;"	d
+snes_wr_enable	sram.h	178;"	d
+soft_reset	watchdog.h	32;"	d
+sram_bulk_addr_restore	sram.c	/^inline void sram_bulk_addr_restore()$/;"	f
+sram_bulk_addr_save	sram.c	/^inline void sram_bulk_addr_save()$/;"	f
+sram_bulk_copy	sram.c	/^void sram_bulk_copy_from_buffer(uint32_t addr, uint8_t * src, uint32_t len)$/;"	f
+sram_bulk_read	sram.c	/^inline uint8_t sram_bulk_read(void)$/;"	f
+sram_bulk_copy_into_buffer	sram.c	/^void sram_bulk_copy_into_buffer(uint32_t addr, uint8_t * dst, uint32_t len)$/;"	f
+sram_bulk_read_end	sram.c	/^void sram_bulk_read_end(void)$/;"	f
+sram_bulk_read_next	sram.c	/^inline void sram_bulk_read_next(void)$/;"	f
+sram_bulk_read_start	sram.c	/^void sram_bulk_read_start(uint32_t addr)$/;"	f
+sram_bulk_set	sram.c	/^void sram_bulk_set(uint32_t addr, uint32_t len,uint8_t value){$/;"	f
+sram_bulk_write	sram.c	/^inline void sram_bulk_write( uint8_t data)$/;"	f
+sram_bulk_write_end	sram.c	/^void sram_bulk_write_end(void)$/;"	f
+sram_bulk_write_next	sram.c	/^inline void sram_bulk_write_next(void)$/;"	f
+sram_bulk_write_start	sram.c	/^void sram_bulk_write_start(uint32_t addr)$/;"	f
+sram_read	sram.c	/^uint8_t sram_read(uint32_t addr)$/;"	f
+sram_write	sram.c	/^void sram_write(uint32_t addr, uint8_t data)$/;"	f
+sreg_set	sram.c	/^void sreg_set(uint32_t addr)$/;"	f
+startSectors	fat.h	/^	unsigned long int   startSectors;	\/\/ der erste sektor in einer reihe (freie oder verkettete)$/;"	m	struct:Fat
+sync_errors	main.c	/^uint16_t sync_errors = 0;$/;"	v
+system_init	sram.c	/^void system_init(void)$/;"	f
+test_bulk_read_write	testing.c	/^void test_bulk_read_write()$/;"	f
+test_crc	testing.c	/^void test_crc()$/;"	f
+test_non_zero_memory	testing.c	/^void test_non_zero_memory(uint32_t bottom_addr, uint32_t top_addr)$/;"	f
+test_read_write	testing.c	/^void test_read_write()$/;"	f
+test_sdcard	testing.c	/^void test_sdcard(void){$/;"	f
+timer_start	timer.c	/^void timer_start( void )$/;"	f
+timer_stop_int	timer.c	/^uint16_t timer_stop_int(void)$/;"	f
+tmr_int	uart.c	/^    uint8_t tmr_int:1;$/;"	m	struct:__anon2	file:
+tx_buffer	main.c	/^uint8_t tx_buffer[32];$/;"	v
+tx_remaining	main.c	/^uint8_t tx_remaining = 0;$/;"	v
+uart_init	uart.c	/^void uart_init(void)$/;"	f
+uart_putc	uart.c	/^void uart_putc(uint8_t c)$/;"	f
+uart_puts	uart.c	/^void uart_puts(const char *s)$/;"	f
+uart_puts_P	uart.c	/^void uart_puts_P(PGM_P s)$/;"	f
+uart_stdout	uart.c	/^FILE uart_stdout = FDEV_SETUP_STREAM(uart_stream, NULL, _FDEV_SETUP_WRITE);$/;"	v
+uart_stream	uart.c	/^static int uart_stream(char c, FILE * stream)$/;"	f	file:
+uint	timer.c	47;"	d	file:
+uint8_t	timer.c	46;"	d	file:
+usbFunctionRead	usb_bulk.c	/^uint8_t usbFunctionRead(uint8_t * data, uint8_t len)$/;"	f
+usbFunctionSetup	main.c	/^usbMsgLen_t usbFunctionSetup(uchar data[8])$/;"	f
+usbFunctionWrite	usb_bulk.c	/^uint8_t usbFunctionWrite(uint8_t * data, uint8_t len)$/;"	f
+usb_connect	main.c	/^void usb_connect()$/;"	f
+wdt_init	watchdog.c	/^void wdt_init(void)$/;"	f
+write2end	fifo.h	/^    uint8_t read2end, write2end;        \/\/ # Zeichen bis zum Überlauf Lese-\/Schreibzeiger$/;"	m	struct:__anon1

avr/usbload/testing.c

@@ -31,6 +31,7 @@
 #include "debug.h"
 #include "crc.h"
 #include "info.h"
+#include "dump.h"
 
 void test_read_write()
 {
@@ -45,7 +46,7 @@ void test_read_write()
     }
     addr = 0x000000;
     while (addr++ <= 0x0000ff) {
-        info("read addr=0x%08lx %x\n", addr, sram_read(addr));
+        info_P(PSTR("read addr=0x%08lx %x\n"), addr, sram_read(addr));
     }
 }
 
@@ -69,7 +70,7 @@ void test_bulk_read_write()
     addr = 0x000000;
     sram_bulk_read_start(addr);
     while (addr <= 0x8000) {
-        info("addr=0x%08lx %x\n", addr, sram_bulk_read());
+        info_P(PSTR("addr=0x%08lx %x\n"), addr, sram_bulk_read());
         sram_bulk_read_next();
         addr++;
     }
@@ -85,22 +86,52 @@ void test_non_zero_memory(uint32_t bottom_addr, uint32_t top_addr)
     for (addr = bottom_addr; addr < top_addr; addr++) {
         c = sram_bulk_read();
         if (c != 0xff)
-            info("addr=0x%08lx c=0x%x\n", addr, c);
+            info_P(PSTR("addr=0x%08lx c=0x%x\n"), addr, c);
         sram_bulk_read_next();
     }
     sram_bulk_read_end();
 }
 
 
+void test_memory_pattern(uint32_t bottom_addr, uint32_t top_addr,
+                         uint32_t bank_size)
+{
+    uint32_t addr = 0;
+    uint8_t pattern = 0x55;
+    info_P(PSTR("test_memory_pattern: bottom_addr=0x%08lx top_addr=0x%08lx\n"),
+           bottom_addr, top_addr);
+    sram_bulk_write_start(bottom_addr);
+    for (addr = bottom_addr; addr < top_addr; addr++) {
+        if (addr % bank_size == 0) {
+            pattern++;
+            info_P(PSTR
+                   ("test_memory_pattern: write addr=0x%08lx pattern=0x%08lx\n"),
+                   addr, pattern);
+        }
+        sram_bulk_write(pattern);
+    }
+    sram_bulk_write_end();
+
+
+    for (addr = bottom_addr; addr < top_addr; addr += bank_size) {
+        info_P(PSTR
+               ("test_memory_pattern: dump bottom_addr=0x%08lx top_addr=0x%08lx\n"),
+               addr, addr + bank_size);
+        dump_memory(addr, addr + bank_size);
+        info_P(PSTR
+               ("----------------------------------------------------------------\n"));
+    }
+
+    crc_check_bulk_memory((uint32_t) bottom_addr, top_addr, bank_size);
+}
 
 void test_crc()
 {
-    info("test_crc: clear\n");
+    info_P(PSTR("test_crc: clear\n"));
     avr_bus_active();
     sram_bulk_set(0x000000, 0x10000, 0xff);
-    info("test_crc: crc\n");
+    info_P(PSTR("test_crc: crc\n"));
     crc_check_bulk_memory(0x000000, 0x10000, 0x8000);
-    info("test_crc: check\n");
+    info_P(PSTR("test_crc: check\n"));
     test_non_zero_memory(0x000000, 0x10000);
 }
-

avr/usbload/timer.c

@@ -24,21 +24,24 @@
 #include <stdint.h>
 #include <stdio.h>
 #include <avr/io.h>
-#include <avr/io.h>
 #include <avr/interrupt.h>      /* for sei() */
 
 #include "debug.h"
 #include "info.h"
+#include "sram.h"
+
+
+extern uint8_t snes_reset_line;
 
 #ifndef OCR1A
-    #define OCR1A OCR1  // 2313 support
+#define OCR1A OCR1              // 2313 support
 #endif
 
 #ifndef WGM12
-    #define WGM12 CTC1  // 2313 support
+#define WGM12 CTC1              // 2313 support
 #endif
 
-//#define XTAL      11059201L   // nominal value
+// #define XTAL 11059201L // nominal value
 #define XTAL        20000000UL
 
 #define DEBOUNCE    500L        // debounce clock (256Hz = 4msec)
@@ -47,43 +50,40 @@
 #define uint unsigned int
 
 uint16_t prescaler;
-uint16_t volatile second;          // count seconds
+uint16_t volatile second;       // count seconds
 
- 
+ISR(TIMER1_COMPA_vect)
-ISR (SIG_OUTPUT_COMPARE1A)
 {
 
-#if XTAL % DEBOUNCE                     // bei rest
+
-    OCR1A = 20000000UL / DEBOUNCE - 1;      // compare DEBOUNCE - 1 times
+#if XTAL % DEBOUNCE             // bei rest
+    OCR1A = 20000000UL / DEBOUNCE - 1;  // compare DEBOUNCE - 1 times
 #endif
-  if( --prescaler == 0 ){
+    if (--prescaler == 0) {
-    prescaler = (uint16_t)DEBOUNCE;
+        prescaler = (uint16_t) DEBOUNCE;
-    second++;               // exact one second over
+        second++;               // exact one second over
-#if XTAL % DEBOUNCE         // handle remainder
+#if XTAL % DEBOUNCE             // handle remainder
-    OCR1A = XTAL / DEBOUNCE + XTAL % DEBOUNCE - 1; // compare once per second
+        OCR1A = XTAL / DEBOUNCE + XTAL % DEBOUNCE - 1;  // compare once per second
 #endif
-  }
+    }
 }
 
-void timer_start( void )
+void timer_start(void)
 {
-  TCCR1B = (1<<WGM12) | (1<<CS10);      // divide by 1
+    TCCR1B = (1 << WGM12) | (1 << CS10);        // divide by 1
-                                        // clear on compare
+    // clear on compare
-  OCR1A = XTAL / DEBOUNCE - 1UL;          // Output Compare Register
+    OCR1A = XTAL / DEBOUNCE - 1UL;      // Output Compare Register
-  TCNT1 = 0;                            // Timmer startet mit 0
+    TCNT1 = 0;                  // Timmer startet mit 0
-  second = 0;
+    second = 0;
-  prescaler = (uint16_t)DEBOUNCE;          //software teiler
+    prescaler = (uint16_t) DEBOUNCE;    // software teiler
-  TIMSK1 = 1<<OCIE1A;                    // beim Vergleichswertes Compare Match                    
+    TIMSK1 = 1 << OCIE1A;       // beim Vergleichswertes Compare Match 
-                                        // Interrupt (SIG_OUTPUT_COMPARE1A)
+    // Interrupt (SIG_OUTPUT_COMPARE1A)
-  sei();
+    sei();
 
 }
 
 uint16_t timer_stop_int(void)
 {
-    uint16_t t = ((DEBOUNCE - prescaler) / DEBOUNCE )  + second;
+    uint16_t t = ((DEBOUNCE - prescaler) / DEBOUNCE) + second;
     return t;
 }
-
-
-

avr/usbload/timer.h

@@ -18,12 +18,12 @@
  * =====================================================================================
  */
 
- #ifndef __TIMER_H__
+#ifndef __TIMER_H__
- #define __TIMER_H__
+#define __TIMER_H__
 
 
-int16_t timer_start( void );
+int16_t timer_start(void);
-double timer_stop( void );
+double timer_stop(void);
-int16_t timer_stop_int( void );
+int16_t timer_stop_int(void);
 
 #endif

avr/usbload/uart.c

@@ -25,42 +25,35 @@
 #include "uart.h"
 #include "fifo.h"
 
+
+
 volatile struct {
     uint8_t tmr_int:1;
     uint8_t adc_int:1;
     uint8_t rx_int:1;
 } intflags;
 
-/*
+
- *  * Last character read from the UART.
- *   
- */
 volatile char rxbuff;
 
 
+
+static int uart_stream(char c, FILE * stream);
+
 FILE uart_stdout = FDEV_SETUP_STREAM(uart_stream, NULL, _FDEV_SETUP_WRITE);
 
 void uart_init(void)
 {
-    UCSR0A = _BV(U2X0);           /* improves baud rate error @ F_CPU = 1 MHz */
+    UCSR0A = _BV(U2X0);         /* improves baud rate error @ F_CPU = 1 MHz */
-    UCSR0B = _BV(TXEN0) | _BV(RXEN0) | _BV(RXCIE0); /* tx/rx enable, rx complete
+    UCSR0B = _BV(TXEN0) | _BV(RXEN0) | _BV(RXCIE0);     /* tx/rx enable, rx complete * intr */
-                                                 * intr */
     UBRR0L = (F_CPU / (8 * 115200UL)) - 1;
 
 
 }
 
-
+/*
-ISR(USART0_RX_vect)
+ * ISR(USART0_RX_vect) { uint8_t c; c = UDR0; if (bit_is_clear(UCSR0A, FE0)) { rxbuff = c; intflags.rx_int = 1; } } 
-{
+ */
-    uint8_t c;
-    c = UDR0;
-    if (bit_is_clear(UCSR0A, FE0)) {
-        rxbuff = c;
-        intflags.rx_int = 1;
-    }
-}
-
 
 void uart_putc(uint8_t c)
 {

avr/usbload/uart.h

@@ -32,9 +32,5 @@ void uart_init(void);
 void uart_putc(const uint8_t);
 void uart_puts(const char *s);
 void uart_puts_P(PGM_P s);
-static int uart_stream(char c, FILE *stream);
 
 #endif
-
-
-

avr/usbload/usb_bulk.c

@@ -27,8 +27,7 @@
 #include <stdlib.h>
 
 #include "usbdrv.h"
-#include "oddebug.h"            /* This is also an example for using debug
+#include "oddebug.h"            /* This is also an example for using debug macros */
-                                 * macros */
 #include "config.h"
 #include "requests.h"           /* The custom request numbers we use */
 #include "uart.h"
@@ -39,54 +38,48 @@
 #include "crc.h"
 #include "usb_bulk.h"
 
-extern uint8_t read_buffer[TRANSFER_BUFFER_SIZE];
+
-extern uint32_t req_addr;
+extern usb_transaction_t usb_trans;
-extern uint32_t req_size;
-extern uint8_t req_bank;
-extern uint32_t req_bank_size;
-extern uint8_t req_state;
-extern uint8_t rx_remaining; 
-extern uint8_t tx_remaining;
-extern  uint8_t tx_buffer[32];
-extern uint16_t crc;
 
 uint8_t usbFunctionWrite(uint8_t * data, uint8_t len)
 {
     uint8_t *ptr;
-    uint8_t  i;
+    uint8_t i;
 
-    if (len > rx_remaining) {
+    if (len > usb_trans.rx_remaining) {
-        info("ERROR:usbFunctionWrite more data than expected remain: %i len: %i\n",
+        info_P(PSTR
-               rx_remaining, len);
+               ("ERROR:usbFunctionWrite more data than expected remain: %i len: %i\n"),
-        len = rx_remaining;
+               usb_trans.rx_remaining, len);
+        len = usb_trans.rx_remaining;
     }
-    if (req_state == REQ_STATUS_BULK_UPLOAD) {
+    if (usb_trans.req_state == REQ_STATUS_BULK_UPLOAD) {
 
-        rx_remaining -= len;
+        usb_trans.rx_remaining -= len;
-        debug(DEBUG_USB_TRANS,"usbFunctionWrite REQ_STATUS_BULK_UPLOAD addr: 0x%08lx len: %i rx_remaining=%i\n",
+        debug_P(DEBUG_USB_TRANS,
-               req_addr, len, rx_remaining);
+                PSTR
+                ("usbFunctionWrite REQ_STATUS_BULK_UPLOAD addr: 0x%08lx len: %i rx_remaining=%i\n"),
+                usb_trans.req_addr, len, usb_trans.rx_remaining);
         ptr = data;
         i = len;
-        while(i--){
+        while (i--) {
             sram_bulk_write(*ptr++);
             sram_bulk_write_next();
         }
     }
-    /* test this */
-    //return rx_remaining == 0
     return len;
 }
 
 uint8_t usbFunctionRead(uint8_t * data, uint8_t len)
 {
     uint8_t i;
-    if (len > tx_remaining)
+    if (len > usb_trans.tx_remaining)
-        len = tx_remaining;
+        len = usb_trans.tx_remaining;
-    tx_remaining -= len;
+    usb_trans.tx_remaining -= len;
-    debug(DEBUG_USB_TRANS,"usbFunctionRead len=%i tx_remaining=%i \n", len, tx_remaining);
+    debug_P(DEBUG_USB_TRANS, PSTR("usbFunctionRead len=%i tx_remaining=%i \n"),
+            len, usb_trans.tx_remaining);
 
     for (i = 0; i < len; i++) {
-        *data = tx_buffer[len];
+        *data = usb_trans.tx_buffer[len];
         data++;
     }
     return len;

avr/usbload/usbconfig.h

@@ -20,325 +20,287 @@
 
 
 
-/* Name: usbconfig.h
+/*
- * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
+ * Name: usbconfig.h Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers Author: Christian Starkjohann Creation Date:
- * Author: Christian Starkjohann
+ * 2005-04-01 Tabsize: 4 Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH License: GNU GPL v2 (see License.txt), GNU GPL v3 or
- * Creation Date: 2005-04-01
+ * proprietary (CommercialLicense.txt) This Revision: $Id: usbconfig-prototype.h 740 2009-04-13 18:23:31Z cs $ 
- * Tabsize: 4
- * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbconfig-prototype.h 740 2009-04-13 18:23:31Z cs $
  */
 
 #ifndef __usbconfig_h_included__
 #define __usbconfig_h_included__
 
 /*
-General Description:
+ * General Description: This file is an example configuration (with inline documentation) for the USB driver. It configures V-USB for USB
-This file is an example configuration (with inline documentation) for the USB
+ * D+ connected to Port D bit 2 (which is also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may wire the lines to
-driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
+ * any other port, as long as D+ is also wired to INT0 (or any other hardware interrupt, as long as it is the highest level interrupt, see
-also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
+ * section at the end of this file). 
-wire the lines to any other port, as long as D+ is also wired to INT0 (or any
+ */
-other hardware interrupt, as long as it is the highest level interrupt, see
-section at the end of this file).
-*/
 
-/* ---------------------------- Hardware Config ---------------------------- */
+/*
+ * ---------------------------- Hardware Config ---------------------------- 
+ */
 
 #define USB_CFG_IOPORTNAME      D
-/* This is the port where the USB bus is connected. When you configure it to
+/*
- * "B", the registers PORTB, PINB and DDRB will be used.
+ * This is the port where the USB bus is connected. When you configure it to "B", the registers PORTB, PINB and DDRB will be used. 
  */
 #define USB_CFG_DMINUS_BIT      4
-/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
+/*
- * This may be any bit in the port.
+ * This is the bit number in USB_CFG_IOPORT where the USB D- line is connected. This may be any bit in the port. 
  */
 #define USB_CFG_DPLUS_BIT       2
-/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
+/*
- * This may be any bit in the port. Please note that D+ must also be connected
+ * This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected. This may be any bit in the port. Please note that D+ must
- * to interrupt pin INT0! [You can also use other interrupts, see section
+ * also be connected to interrupt pin INT0! [You can also use other interrupts, see section "Optional MCU Description" below, or you can
- * "Optional MCU Description" below, or you can connect D- to the interrupt, as
+ * connect D- to the interrupt, as it is required if you use the USB_COUNT_SOF feature. If you use D- for the interrupt, the USB interrupt
- * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
+ * will also be triggered at Start-Of-Frame markers every millisecond.] 
- * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
- * markers every millisecond.]
  */
 #define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
-/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
+/*
- * 16500 and 20000. The 12.8 MHz and 16.5 MHz versions of the code require no
+ * Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000, 16500 and 20000. The 12.8 MHz and 16.5 MHz versions of the
- * crystal, they tolerate +/- 1% deviation from the nominal frequency. All
+ * code require no crystal, they tolerate +/- 1% deviation from the nominal frequency. All other rates require a precision of 2000 ppm and
- * other rates require a precision of 2000 ppm and thus a crystal!
+ * thus a crystal! Default if not specified: 12 MHz 
- * Default if not specified: 12 MHz
  */
 #define USB_CFG_CHECK_CRC       0
-/* Define this to 1 if you want that the driver checks integrity of incoming
+/*
- * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * Define this to 1 if you want that the driver checks integrity of incoming data packets (CRC checks). CRC checks cost quite a bit of code 
- * currently only available for 18 MHz crystal clock. You must choose
+ * size and are currently only available for 18 MHz crystal clock. You must choose USB_CFG_CLOCK_KHZ = 18000 if you enable this option. 
- * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
  */
 
-/* ----------------------- Optional Hardware Config ------------------------ */
+/*
-
+ * ----------------------- Optional Hardware Config ------------------------ 
-//#define USB_CFG_PULLUP_IOPORTNAME   D 
-/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
- * V+, you can connect and disconnect the device from firmware by calling
- * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
- * This constant defines the port on which the pullup resistor is connected.
- */
-//#define USB_CFG_PULLUP_BIT          6 
-/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
- * above) where the 1.5k pullup resistor is connected. See description
- * above for details.
  */
 
-/* --------------------------- Functional Range ---------------------------- */
+// #define USB_CFG_PULLUP_IOPORTNAME D 
+/*
+ * If you connect the 1.5k pullup resistor from D- to a port pin instead of V+, you can connect and disconnect the device from firmware by
+ * calling the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h). This constant defines the port on which the pullup
+ * resistor is connected. 
+ */
+// #define USB_CFG_PULLUP_BIT 6 
+/*
+ * This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined above) where the 1.5k pullup resistor is connected. See
+ * description above for details. 
+ */
+
+/*
+ * --------------------------- Functional Range ---------------------------- 
+ */
 
 #define USB_CFG_HAVE_INTRIN_ENDPOINT    0
-/* Define this to 1 if you want to compile a version with two endpoints: The
+/*
- * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
+ * Define this to 1 if you want to compile a version with two endpoints: The default control endpoint 0 and an interrupt-in endpoint (any
- * number).
+ * other endpoint number). 
  */
 #define USB_CFG_HAVE_INTRIN_ENDPOINT3   0
-/* Define this to 1 if you want to compile a version with three endpoints: The
+/*
- * default control endpoint 0, an interrupt-in endpoint 3 (or the number
+ * Define this to 1 if you want to compile a version with three endpoints: The default control endpoint 0, an interrupt-in endpoint 3 (or
- * configured below) and a catch-all default interrupt-in endpoint as above.
+ * the number configured below) and a catch-all default interrupt-in endpoint as above. You must also define USB_CFG_HAVE_INTRIN_ENDPOINT
- * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
+ * to 1 for this feature. 
  */
 #define USB_CFG_EP3_NUMBER              3
-/* If the so-called endpoint 3 is used, it can now be configured to any other
+/*
- * endpoint number (except 0) with this macro. Default if undefined is 3.
+ * If the so-called endpoint 3 is used, it can now be configured to any other endpoint number (except 0) with this macro. Default if
+ * undefined is 3. 
  */
-/* #define USB_INITIAL_DATATOKEN           USBPID_DATA1 */
+/*
-/* The above macro defines the startup condition for data toggling on the
+ * #define USB_INITIAL_DATATOKEN USBPID_DATA1 
- * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
+ */
- * Since the token is toggled BEFORE sending any data, the first packet is
+/*
- * sent with the oposite value of this configuration!
+ * The above macro defines the startup condition for data toggling on the interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1. Since 
+ * the token is toggled BEFORE sending any data, the first packet is sent with the oposite value of this configuration! 
  */
 #define USB_CFG_IMPLEMENT_HALT          0
-/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
+/*
- * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
+ * Define this to 1 if you also want to implement the ENDPOINT_HALT feature for endpoint 1 (interrupt endpoint). Although you may not need
- * it is required by the standard. We have made it a config option because it
+ * this feature, it is required by the standard. We have made it a config option because it bloats the code considerably. 
- * bloats the code considerably.
  */
 #define USB_CFG_SUPPRESS_INTR_CODE      1
-/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
+/*
- * want to send any data over them. If this macro is defined to 1, functions
+ * Define this to 1 if you want to declare interrupt-in endpoints, but don't want to send any data over them. If this macro is defined to
- * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
+ * 1, functions usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if you need the interrupt-in endpoints in order to
- * you need the interrupt-in endpoints in order to comply to an interface
+ * comply to an interface (e.g. HID), but never want to send any data. This option saves a couple of bytes in flash memory and the transmit 
- * (e.g. HID), but never want to send any data. This option saves a couple
+ * buffers in RAM. 
- * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      200
+#define USB_CFG_INTR_POLL_INTERVAL      20
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
+/*
- * interval. The value is in milliseconds and must not be less than 10 ms for
+ * If you compile a version with endpoint 1 (interrupt-in), this is the poll interval. The value is in milliseconds and must not be less
- * low speed devices.
+ * than 10 ms for low speed devices. 
  */
 #define USB_CFG_IS_SELF_POWERED         0
-/* Define this to 1 if the device has its own power supply. Set it to 0 if the
+/*
- * device is powered from the USB bus.
+ * Define this to 1 if the device has its own power supply. Set it to 0 if the device is powered from the USB bus. 
  */
 #define USB_CFG_MAX_BUS_POWER           300
-/* Set this variable to the maximum USB bus power consumption of your device.
+/*
- * The value is in milliamperes. [It will be divided by two since USB
+ * Set this variable to the maximum USB bus power consumption of your device. The value is in milliamperes. [It will be divided by two
- * communicates power requirements in units of 2 mA.]
+ * since USB communicates power requirements in units of 2 mA.] 
  */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
-/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
+/*
- * transfers. Set it to 0 if you don't need it and want to save a couple of
+ * Set this to 1 if you want usbFunctionWrite() to be called for control-out transfers. Set it to 0 if you don't need it and want to save a 
- * bytes.
+ * couple of bytes. 
  */
 #define USB_CFG_IMPLEMENT_FN_READ       0
-/* Set this to 1 if you need to send control replies which are generated
+/*
- * "on the fly" when usbFunctionRead() is called. If you only want to send
+ * Set this to 1 if you need to send control replies which are generated "on the fly" when usbFunctionRead() is called. If you only want to 
- * data from a static buffer, set it to 0 and return the data from
+ * send data from a static buffer, set it to 0 and return the data from usbFunctionSetup(). This saves a couple of bytes. 
- * usbFunctionSetup(). This saves a couple of bytes.
  */
 #define USB_CFG_IMPLEMENT_FN_WRITEOUT   0
-/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
+/*
- * You must implement the function usbFunctionWriteOut() which receives all
+ * Define this to 1 if you want to use interrupt-out (or bulk out) endpoints. You must implement the function usbFunctionWriteOut() which
- * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
+ * receives all interrupt/bulk data sent to any endpoint other than 0. The endpoint number can be found in 'usbRxToken'. 
- * can be found in 'usbRxToken'.
  */
 #define USB_CFG_HAVE_FLOWCONTROL        0
-/* Define this to 1 if you want flowcontrol over USB data. See the definition
+/*
- * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
+ * Define this to 1 if you want flowcontrol over USB data. See the definition of the macros usbDisableAllRequests() and
- * usbdrv.h.
+ * usbEnableAllRequests() in usbdrv.h. 
  */
 #define USB_CFG_LONG_TRANSFERS          0
-/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
+/*
- * in a single control-in or control-out transfer. Note that the capability
+ * Define this to 1 if you want to send/receive blocks of more than 254 bytes in a single control-in or control-out transfer. Note that the 
- * for long transfers increases the driver size.
+ * capability for long transfers increases the driver size. 
  */
-/* #define USB_RX_USER_HOOK(data, len)     if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
+/*
-/* This macro is a hook if you want to do unconventional things. If it is
+ * #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); 
- * defined, it's inserted at the beginning of received message processing.
- * If you eat the received message and don't want default processing to
- * proceed, do a return after doing your things. One possible application
- * (besides debugging) is to flash a status LED on each packet.
  */
-/* #define USB_RESET_HOOK(resetStarts)     if(!resetStarts){hadUsbReset();} */
+/*
-/* This macro is a hook if you need to know when an USB RESET occurs. It has
+ * This macro is a hook if you want to do unconventional things. If it is defined, it's inserted at the beginning of received message
- * one parameter which distinguishes between the start of RESET state and its
+ * processing. If you eat the received message and don't want default processing to proceed, do a return after doing your things. One
- * end.
+ * possible application (besides debugging) is to flash a status LED on each packet. 
  */
-/* #define USB_SET_ADDRESS_HOOK()              hadAddressAssigned(); */
+/*
-/* This macro (if defined) is executed when a USB SET_ADDRESS request was
+ * #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} 
- * received.
+ */
+/*
+ * This macro is a hook if you need to know when an USB RESET occurs. It has one parameter which distinguishes between the start of RESET
+ * state and its end. 
+ */
+/*
+ * #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); 
+ */
+/*
+ * This macro (if defined) is executed when a USB SET_ADDRESS request was received. 
  */
 #define USB_COUNT_SOF                   0
-/* define this macro to 1 if you need the global variable "usbSofCount" which
+/*
- * counts SOF packets. This feature requires that the hardware interrupt is
+ * define this macro to 1 if you need the global variable "usbSofCount" which counts SOF packets. This feature requires that the hardware
- * connected to D- instead of D+.
+ * interrupt is connected to D- instead of D+. 
  */
-/* #ifdef __ASSEMBLER__
+/*
- * macro myAssemblerMacro
+ * #ifdef __ASSEMBLER__ macro myAssemblerMacro in YL, TCNT0 sts timer0Snapshot, YL endm #endif #define USB_SOF_HOOK myAssemblerMacro This
- *     in      YL, TCNT0
+ * macro (if defined) is executed in the assembler module when a Start Of Frame condition is detected. It is recommended to define it to
- *     sts     timer0Snapshot, YL
+ * the name of an assembler macro which is defined here as well so that more than one assembler instruction can be used. The macro may use
- *     endm
+ * the register YL and modify SREG. If it lasts longer than a couple of cycles, USB messages immediately after an SOF pulse may be lost and 
- * #endif
+ * must be retried by the host. What can you do with this hook? Since the SOF signal occurs exactly every 1 ms (unless the host is in sleep 
- * #define USB_SOF_HOOK                    myAssemblerMacro
+ * mode), you can use it to tune OSCCAL in designs running on the internal RC oscillator. Please note that Start Of Frame detection works
- * This macro (if defined) is executed in the assembler module when a
+ * only if D- is wired to the interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES! 
- * Start Of Frame condition is detected. It is recommended to define it to
- * the name of an assembler macro which is defined here as well so that more
- * than one assembler instruction can be used. The macro may use the register
- * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
- * immediately after an SOF pulse may be lost and must be retried by the host.
- * What can you do with this hook? Since the SOF signal occurs exactly every
- * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
- * designs running on the internal RC oscillator.
- * Please note that Start Of Frame detection works only if D- is wired to the
- * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
  */
 #define USB_CFG_CHECK_DATA_TOGGLING     0
-/* define this macro to 1 if you want to filter out duplicate data packets
+/*
- * sent by the host. Duplicates occur only as a consequence of communication
+ * define this macro to 1 if you want to filter out duplicate data packets sent by the host. Duplicates occur only as a consequence of
- * errors, when the host does not receive an ACK. Please note that you need to
+ * communication errors, when the host does not receive an ACK. Please note that you need to implement the filtering yourself in
- * implement the filtering yourself in usbFunctionWriteOut() and
+ * usbFunctionWriteOut() and usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable for each control- and
- * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
+ * out-endpoint to check for duplicate packets. 
- * for each control- and out-endpoint to check for duplicate packets.
  */
 #define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   0
-/* define this macro to 1 if you want the function usbMeasureFrameLength()
+/*
- * compiled in. This function can be used to calibrate the AVR's RC oscillator.
+ * define this macro to 1 if you want the function usbMeasureFrameLength() compiled in. This function can be used to calibrate the AVR's RC 
+ * oscillator. 
  */
 
-/* -------------------------- Device Description --------------------------- */
+/*
+ * -------------------------- Device Description --------------------------- 
+ */
 
 #define  USB_CFG_VENDOR_ID       0xc0, 0x16
-/* USB vendor ID for the device, low byte first. If you have registered your
+/*
- * own Vendor ID, define it here. Otherwise you use one of obdev's free shared
+ * USB vendor ID for the device, low byte first. If you have registered your own Vendor ID, define it here. Otherwise you use one of
- * VID/PID pairs. Be sure to read USBID-License.txt for rules!
+ * obdev's free shared VID/PID pairs. Be sure to read USBID-License.txt for rules! 
  */
 #define  USB_CFG_DEVICE_ID       0xdd, 0x05
-/* This is the ID of the product, low byte first. It is interpreted in the
+/*
- * scope of the vendor ID. If you have registered your own VID with usb.org
+ * This is the ID of the product, low byte first. It is interpreted in the scope of the vendor ID. If you have registered your own VID with 
- * or if you have licensed a PID from somebody else, define it here. Otherwise
+ * usb.org or if you have licensed a PID from somebody else, define it here. Otherwise you use obdev's free shared VID/PID pair. Be sure to 
- * you use obdev's free shared VID/PID pair. Be sure to read the rules in
+ * read the rules in USBID-License.txt! 
- * USBID-License.txt!
  */
 #define USB_CFG_DEVICE_VERSION  0x00, 0x01
-/* Version number of the device: Minor number first, then major number.
+/*
+ * Version number of the device: Minor number first, then major number. 
  */
 #define USB_CFG_VENDOR_NAME     'o', 'p', 't', 'i', 'x', 'x', '.', 'o', 'r', 'g'
 #define USB_CFG_VENDOR_NAME_LEN 10
-/* These two values define the vendor name returned by the USB device. The name
+/*
- * must be given as a list of characters under single quotes. The characters
+ * These two values define the vendor name returned by the USB device. The name must be given as a list of characters under single quotes.
- * are interpreted as Unicode (UTF-16) entities.
+ * The characters are interpreted as Unicode (UTF-16) entities. If you don't want a vendor name string, undefine these macros. ALWAYS
- * If you don't want a vendor name string, undefine these macros.
+ * define a vendor name containing your Internet domain name if you use obdev's free shared VID/PID pair. See the file USBID-License.txt
- * ALWAYS define a vendor name containing your Internet domain name if you use
+ * for details. 
- * obdev's free shared VID/PID pair. See the file USBID-License.txt for
- * details.
  */
-#define USB_CFG_DEVICE_NAME     'S', 'N', 'E', 'S', 'R', 'A', 'M'
+#define USB_CFG_DEVICE_NAME     'Q', 'U', 'I', 'C', 'K', 'D', 'E', 'V', '1', '6'
-#define USB_CFG_DEVICE_NAME_LEN 7
+#define USB_CFG_DEVICE_NAME_LEN 10
-/* Same as above for the device name. If you don't want a device name, undefine
+/*
- * the macros. See the file USBID-License.txt before you assign a name if you
+ * Same as above for the device name. If you don't want a device name, undefine the macros. See the file USBID-License.txt before you
- * use a shared VID/PID.
+ * assign a name if you use a shared VID/PID. 
  */
-/*#define USB_CFG_SERIAL_NUMBER   'N', 'o', 'n', 'e' */
+/*
-/*#define USB_CFG_SERIAL_NUMBER_LEN   0 */
+ * #define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' 
-/* Same as above for the serial number. If you don't want a serial number,
- * undefine the macros.
- * It may be useful to provide the serial number through other means than at
- * compile time. See the section about descriptor properties below for how
- * to fine tune control over USB descriptors such as the string descriptor
- * for the serial number.
  */
-#define USB_CFG_DEVICE_CLASS        0xff    /* set to 0 if deferred to interface */
+/*
+ * #define USB_CFG_SERIAL_NUMBER_LEN 0 
+ */
+/*
+ * Same as above for the serial number. If you don't want a serial number, undefine the macros. It may be useful to provide the serial
+ * number through other means than at compile time. See the section about descriptor properties below for how to fine tune control over USB 
+ * descriptors such as the string descriptor for the serial number. 
+ */
+#define USB_CFG_DEVICE_CLASS        0xff        /* set to 0 if deferred to interface */
 #define USB_CFG_DEVICE_SUBCLASS     0
-/* See USB specification if you want to conform to an existing device class.
+/*
- * Class 0xff is "vendor specific".
+ * See USB specification if you want to conform to an existing device class. Class 0xff is "vendor specific". 
  */
 #define USB_CFG_INTERFACE_CLASS     0   /* define class here if not at device level */
 #define USB_CFG_INTERFACE_SUBCLASS  0
 #define USB_CFG_INTERFACE_PROTOCOL  0
-/* See USB specification if you want to conform to an existing device class or
+/*
- * protocol. The following classes must be set at interface level:
+ * See USB specification if you want to conform to an existing device class or protocol. The following classes must be set at interface
- * HID class is 3, no subclass and protocol required (but may be useful!)
+ * level: HID class is 3, no subclass and protocol required (but may be useful!) CDC class is 2, use subclass 2 and protocol 1 for ACM 
- * CDC class is 2, use subclass 2 and protocol 1 for ACM
  */
- #define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH    0
+#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH    0
 
-/* Define this to the length of the HID report descriptor, if you implement
+/*
- * an HID device. Otherwise don't define it or define it to 0.
+ * Define this to the length of the HID report descriptor, if you implement an HID device. Otherwise don't define it or define it to 0. If
- * If you use this define, you must add a PROGMEM character array named
+ * you use this define, you must add a PROGMEM character array named "usbHidReportDescriptor" to your code which contains the report
- * "usbHidReportDescriptor" to your code which contains the report descriptor.
+ * descriptor. Don't forget to keep the array and this define in sync! 
- * Don't forget to keep the array and this define in sync!
  */
 
-/* #define USB_PUBLIC static */
+/*
-/* Use the define above if you #include usbdrv.c instead of linking against it.
+ * #define USB_PUBLIC static 
- * This technique saves a couple of bytes in flash memory.
+ */
+/*
+ * Use the define above if you #include usbdrv.c instead of linking against it. This technique saves a couple of bytes in flash memory. 
  */
 
-/* ------------------- Fine Control over USB Descriptors ------------------- */
+/*
-/* If you don't want to use the driver's default USB descriptors, you can
+ * ------------------- Fine Control over USB Descriptors ------------------- 
- * provide our own. These can be provided as (1) fixed length static data in
+ */
- * flash memory, (2) fixed length static data in RAM or (3) dynamically at
+/*
- * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
+ * If you don't want to use the driver's default USB descriptors, you can provide our own. These can be provided as (1) fixed length static 
- * information about this function.
+ * data in flash memory, (2) fixed length static data in RAM or (3) dynamically at runtime in the function usbFunctionDescriptor(). See
- * Descriptor handling is configured through the descriptor's properties. If
+ * usbdrv.h for more information about this function. Descriptor handling is configured through the descriptor's properties. If no
- * no properties are defined or if they are 0, the default descriptor is used.
+ * properties are defined or if they are 0, the default descriptor is used. Possible properties are: + USB_PROP_IS_DYNAMIC: The data for
- * Possible properties are:
+ * the descriptor should be fetched at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is used, the data is in FLASH by
- *   + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
+ * default. Add property USB_PROP_IS_RAM if you want RAM pointers.  + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or
- *     at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
+ * found in static memory is in RAM, not in flash memory.  + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash), the
- *     used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
+ * driver must know the descriptor's length. The descriptor itself is found at the address of a well known identifier (see below). List of
- *     you want RAM pointers.
+ * static descriptor names (must be declared PROGMEM if in flash): char usbDescriptorDevice[]; char usbDescriptorConfiguration[]; char
- *   + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
+ * usbDescriptorHidReport[]; char usbDescriptorString0[]; int usbDescriptorStringVendor[]; int usbDescriptorStringDevice[]; int
- *     in static memory is in RAM, not in flash memory.
+ * usbDescriptorStringSerialNumber[]; Other descriptors can't be provided statically, they must be provided dynamically at runtime.
- *   + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
+ * Descriptor properties are or-ed or added together, e.g.: #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18)) The 
- *     the driver must know the descriptor's length. The descriptor itself is
+ * following descriptors are defined: USB_CFG_DESCR_PROPS_DEVICE USB_CFG_DESCR_PROPS_CONFIGURATION USB_CFG_DESCR_PROPS_STRINGS
- *     found at the address of a well known identifier (see below).
+ * USB_CFG_DESCR_PROPS_STRING_0 USB_CFG_DESCR_PROPS_STRING_VENDOR USB_CFG_DESCR_PROPS_STRING_PRODUCT
- * List of static descriptor names (must be declared PROGMEM if in flash):
+ * USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_CFG_DESCR_PROPS_HID USB_CFG_DESCR_PROPS_HID_REPORT USB_CFG_DESCR_PROPS_UNKNOWN (for all
- *   char usbDescriptorDevice[];
+ * descriptors not handled by the driver) Note about string descriptors: String descriptors are not just strings, they are Unicode strings 
- *   char usbDescriptorConfiguration[];
+ * prefixed with a 2 byte header. Example: int serialNumberDescriptor[] = { USB_STRING_DESCRIPTOR_HEADER(6), 'S', 'e', 'r', 'i', 'a', 'l'
- *   char usbDescriptorHidReport[];
- *   char usbDescriptorString0[];
- *   int usbDescriptorStringVendor[];
- *   int usbDescriptorStringDevice[];
- *   int usbDescriptorStringSerialNumber[];
- * Other descriptors can't be provided statically, they must be provided
- * dynamically at runtime.
- *
- * Descriptor properties are or-ed or added together, e.g.:
- * #define USB_CFG_DESCR_PROPS_DEVICE   (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
- *
- * The following descriptors are defined:
- *   USB_CFG_DESCR_PROPS_DEVICE
- *   USB_CFG_DESCR_PROPS_CONFIGURATION
- *   USB_CFG_DESCR_PROPS_STRINGS
- *   USB_CFG_DESCR_PROPS_STRING_0
- *   USB_CFG_DESCR_PROPS_STRING_VENDOR
- *   USB_CFG_DESCR_PROPS_STRING_PRODUCT
- *   USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
- *   USB_CFG_DESCR_PROPS_HID
- *   USB_CFG_DESCR_PROPS_HID_REPORT
- *   USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
- *
- * Note about string descriptors: String descriptors are not just strings, they
- * are Unicode strings prefixed with a 2 byte header. Example:
- * int  serialNumberDescriptor[] = {
- *     USB_STRING_DESCRIPTOR_HEADER(6),
- *     'S', 'e', 'r', 'i', 'a', 'l'
  * }; 
  */
 
@@ -353,21 +315,38 @@ section at the end of this file).
 #define USB_CFG_DESCR_PROPS_HID_REPORT              0
 #define USB_CFG_DESCR_PROPS_UNKNOWN                 0
 
-/* ----------------------- Optional MCU Description ------------------------ */
+/*
-
+ * ----------------------- Optional MCU Description ------------------------ 
-/* The following configurations have working defaults in usbdrv.h. You
- * usually don't need to set them explicitly. Only if you want to run
- * the driver on a device which is not yet supported or with a compiler
- * which is not fully supported (such as IAR C) or if you use a differnt
- * interrupt than INT0, you may have to define some of these.
  */
-/* #define USB_INTR_CFG            MCUCR */
-/* #define USB_INTR_CFG_SET        ((1 << ISC00) | (1 << ISC01)) */
-/* #define USB_INTR_CFG_CLR        0 */
-/* #define USB_INTR_ENABLE         GIMSK */
-/* #define USB_INTR_ENABLE_BIT     INT0 */
-/* #define USB_INTR_PENDING        GIFR */
-/* #define USB_INTR_PENDING_BIT    INTF0 */
-/* #define USB_INTR_VECTOR         SIG_INTERRUPT0 */
 
-#endif /* __usbconfig_h_included__ */
+/*
+ * The following configurations have working defaults in usbdrv.h. You usually don't need to set them explicitly. Only if you want to run
+ * the driver on a device which is not yet supported or with a compiler which is not fully supported (such as IAR C) or if you use a
+ * differnt interrupt than INT0, you may have to define some of these. 
+ */
+/*
+ * #define USB_INTR_CFG MCUCR 
+ */
+/*
+ * #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) 
+ */
+/*
+ * #define USB_INTR_CFG_CLR 0 
+ */
+/*
+ * #define USB_INTR_ENABLE GIMSK 
+ */
+/*
+ * #define USB_INTR_ENABLE_BIT INT0 
+ */
+/*
+ * #define USB_INTR_PENDING GIFR 
+ */
+/*
+ * #define USB_INTR_PENDING_BIT INTF0 
+ */
+/*
+ * #define USB_INTR_VECTOR SIG_INTERRUPT0 
+ */
+
+#endif                          /* __usbconfig_h_included__ */

avr/usbload/usbdrv/Changelog.txt

@@ -275,3 +275,55 @@ Scroll down to the bottom to see the most recent changes.
     background of USB ID registration clearer.
 
 * Release 2009-04-15
+
+  - Changed CommercialLicense.txt to reflect the new range of PIDs from
+    Jason Kotzin.
+  - Removed USBID-License.txt in favor of USB-IDs-for-free.txt and
+    USB-ID-FAQ.txt
+  - Fixed a bug in the 12.8 MHz module: End Of Packet decection was made in
+    the center between bit 0 and 1 of each byte. This is where the data lines
+    are expected to change and the sampled data may therefore be nonsense.
+    We therefore check EOP ONLY if bits 0 AND 1 have both been read as 0 on D-.
+  - Fixed a bitstuffing problem in the 16 MHz module: If bit 6 was stuffed,
+    the unstuffing code in the receiver routine was 1 cycle too long. If
+    multiple bytes had the unstuffing in bit 6, the error summed up until the
+    receiver was out of sync.
+  - Included option for faster CRC routine.
+    Thanks to Slawomir Fras (BoskiDialer) for this code!
+  - Updated bits in Configuration Descriptor's bmAttributes according to
+    USB 1.1 (in particular bit 7, it is a must-be-set bit now).
+
+* Release 2009-08-22
+
+  - Moved first DBG1() after odDebugInit() in all examples.
+  - Use vector INT0_vect instead of SIG_INTERRUPT0 if defined. This makes
+    V-USB compatible with the new "p" suffix devices (e.g. ATMega328p).
+  - USB_CFG_CLOCK_KHZ setting is now required in usbconfig.h (no default any
+    more).
+  - New option USB_CFG_DRIVER_FLASH_PAGE allows boot loaders on devices with
+    more than 64 kB flash.
+  - Built-in configuration descriptor allows custom definition for second
+    endpoint now.
+
+* Release 2010-07-15
+
+  - Fixed bug in usbDriverSetup() which prevented descriptor sizes above 255
+    bytes.
+  - Avoid a compiler warning for unused parameter in usbHandleResetHook() when
+    compiler option -Wextra is enabled.
+  - Fixed wrong hex value for some IDs in USB-IDs-for-free.txt.
+  - Keep a define for USBATTR_BUSPOWER, although the flag does not exist
+    in USB 1.1 any more. Set it to 0. This is for backward compatibility.
+
+* Release 2012-01-09
+
+  - Define a separate (defined) type for usbMsgPtr so that projects using a
+    tiny memory model can define it to an 8 bit type in usbconfig.h. This
+    change also saves a couple of bytes when using a scalar 16 bit type.
+  - Inserted "const" keyword for all PROGMEM declarations because new GCC
+    requires it.
+  - Fixed problem with dependence of usbportability.h on usbconfig.h. This
+    problem occurred with IAR CC only.
+  - Prepared repository for github.com.
+
+* Release 2012-12-06

avr/usbload/usbdrv/CommercialLicense.txt

@@ -1,5 +1,5 @@
 V-USB Driver Software License Agreement
-Version 2009-04-14
+Version 2012-07-09
 
 THIS LICENSE AGREEMENT GRANTS YOU CERTAIN RIGHTS IN A SOFTWARE. YOU CAN
 ENTER INTO THIS AGREEMENT AND ACQUIRE THE RIGHTS OUTLINED BELOW BY PAYING
@@ -32,13 +32,22 @@ product(s), restricted by the limitations in section 3 below.
 2.3 Modifications. OBJECTIVE DEVELOPMENT grants you the right to modify
 the source code and your copy of V-USB according to your needs.
 
-2.4 USB IDs. OBJECTIVE DEVELOPMENT furnishes you with one or two USB Product
+2.4 USB IDs. OBJECTIVE DEVELOPMENT furnishes you with one or two USB
-ID(s), sent to you in e-mail. These Product IDs are reserved exclusively for
+Product ID(s), sent to you in e-mail. These Product IDs are reserved
-you. They have been obtained from Wouter van Ooijen (www.voti.nl), who has
+exclusively for you. OBJECTIVE DEVELOPMENT has obtained USB Product ID
-reserved the Vendor ID 5824 (decimal) at the USB Implementers Forum, Inc.
+ranges under the Vendor ID 5824 from Wouter van Ooijen (Van Ooijen
-(www.usb.org). This mechanism ensures that there are no Product ID conflicts,
+Technische Informatica, www.voti.nl) and under the Vendor ID 8352 from
-but you cannot become USB certified (enter into the USB-IF Trademark License
+Jason Kotzin (now flirc.tv, Inc.). Both owners of the Vendor IDs have
-Agreement) as you would need your own Vendor ID for that.
+obtained these IDs from the USB Implementers Forum, Inc. (www.usb.org).
+OBJECTIVE DEVELOPMENT disclaims all liability which might arise from the
+assignment of USB IDs.
+
+2.5 USB Certification. Although not part of this agreement, we want to make
+it clear that you cannot become USB certified when you use V-USB or a USB
+Product ID assigned by OBJECTIVE DEVELOPMENT. AVR microcontrollers don't
+meet the electrical specifications required by the USB specification and
+the USB Implementers Forum certifies only members who bought a Vendor ID of
+their own.
 
 
 3 LICENSE RESTRICTIONS

avr/usbload/usbdrv/Readme.txt

@@ -39,8 +39,8 @@ The driver consists of the following files:
                            with IAR's tools.
   License.txt ............ Open Source license for this driver.
   CommercialLicense.txt .. Optional commercial license for this driver.
-  USBID-License.txt ...... Terms and conditions for using particular USB ID
+  USB-ID-FAQ.txt ......... General infos about USB Product- and Vendor-IDs.
-                           values for particular purposes.
+  USB-IDs-for-free.txt ... List and terms of use for free shared PIDs.
 
 (*) ... These files should be linked to your project.
 
@@ -49,8 +49,7 @@ CPU CORE CLOCK FREQUENCY
 ========================
 We supply assembler modules for clock frequencies of 12 MHz, 12.8 MHz, 15 MHz,
 16 MHz, 16.5 MHz 18 MHz and 20 MHz. Other clock rates are not supported. The
-actual clock rate must be configured in usbdrv.h unless you use the default
+actual clock rate must be configured in usbconfig.h.
-12 MHz.
 
 12 MHz Clock
 This is the traditional clock rate of V-USB because it's the lowest clock
@@ -105,7 +104,7 @@ can assign PIDs at will.
 
 Since an entry level cost of 1,500 USD is too high for most small companies
 and hobbyists, we provide some VID/PID pairs for free. See the file
-USBID-License.txt for details.
+USB-IDs-for-free.txt for details.
 
 Objective Development also has some license offerings which include product
 IDs. See http://www.obdev.at/vusb/ for details.
@@ -114,13 +113,28 @@ IDs. See http://www.obdev.at/vusb/ for details.
 DEVELOPMENT SYSTEM
 ==================
 This driver has been developed and optimized for the GNU compiler version 3
-(gcc 3). It does work well with gcc 4, but with bigger code size. We recommend
+and 4. We recommend that you use the GNU compiler suite because it is freely
-that you use the GNU compiler suite because it is freely available. V-USB
+available. V-USB has also been ported to the IAR compiler and assembler. It
-has also been ported to the IAR compiler and assembler. It has been tested
+has been tested with IAR 4.10B/W32 and 4.12A/W32 on an ATmega8 with the
-with IAR 4.10B/W32 and 4.12A/W32 on an ATmega8 with the "small" and "tiny"
+"small" and "tiny" memory model. Not every release is tested with IAR CC and
-memory model. Not every release is tested with IAR CC and the driver may
+the driver may therefore fail to compile with IAR. Please note that gcc is
-therefore fail to compile with IAR. Please note that gcc is more efficient for
+more efficient for usbdrv.c because this module has been deliberately
-usbdrv.c because this module has been deliberately optimized for gcc.
+optimized for gcc.
+
+Gcc version 3 produces smaller code than version 4 due to new optimizing
+capabilities which don't always improve things on 8 bit CPUs. The code size
+generated by gcc 4 can be reduced with the compiler options
+-fno-move-loop-invariants, -fno-tree-scev-cprop and
+-fno-inline-small-functions in addition to -Os. On devices with more than
+8k of flash memory, we also recommend the linker option --relax (written as
+-Wl,--relax for gcc) to convert absolute calls into relative where possible.
+
+For more information about optimizing options see:
+
+    http://www.tty1.net/blog/2008-04-29-avr-gcc-optimisations_en.html
+
+These optimizations are good for gcc 4.x. Version 3.x of gcc does not support
+most of these options and produces good code anyway.
 
 
 USING V-USB FOR FREE

avr/usbload/usbdrv/asmcommon.inc

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id$
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the

avr/usbload/usbdrv/oddebug.c

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: oddebug.c 692 2008-11-07 15:07:40Z cs $
  */
 
 #include "oddebug.h"

avr/usbload/usbdrv/oddebug.h

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: oddebug.h 692 2008-11-07 15:07:40Z cs $
  */
 
 #ifndef __oddebug_h_included__

avr/usbload/usbdrv/usbconfig-prototype.h

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbconfig-prototype.h 740 2009-04-13 18:23:31Z cs $
  */
 
 #ifndef __usbconfig_h_included__
@@ -45,10 +44,12 @@ section at the end of this file).
  */
 #define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
 /* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
- * 16500 and 20000. The 12.8 MHz and 16.5 MHz versions of the code require no
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
- * crystal, they tolerate +/- 1% deviation from the nominal frequency. All
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
- * other rates require a precision of 2000 ppm and thus a crystal!
+ * frequency. All other rates require a precision of 2000 ppm and thus a
- * Default if not specified: 12 MHz
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
  */
 #define USB_CFG_CHECK_CRC       0
 /* Define this to 1 if you want that the driver checks integrity of incoming
@@ -144,6 +145,11 @@ section at the end of this file).
  * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
  * usbdrv.h.
  */
+#define USB_CFG_DRIVER_FLASH_PAGE       0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
 #define USB_CFG_LONG_TRANSFERS          0
 /* Define this to 1 if you want to send/receive blocks of more than 254 bytes
  * in a single control-in or control-out transfer. Note that the capability
@@ -201,24 +207,36 @@ section at the end of this file).
 /* define this macro to 1 if you want the function usbMeasureFrameLength()
  * compiled in. This function can be used to calibrate the AVR's RC oscillator.
  */
+#define USB_USE_FAST_CRC                0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
 
 /* -------------------------- Device Description --------------------------- */
 
-#define  USB_CFG_VENDOR_ID       0xc0, 0x16
+#define  USB_CFG_VENDOR_ID       0xc0, 0x16 /* = 0x16c0 = 5824 = voti.nl */
 /* USB vendor ID for the device, low byte first. If you have registered your
- * own Vendor ID, define it here. Otherwise you use one of obdev's free shared
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
- * VID/PID pairs. Be sure to read USBID-License.txt for rules!
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
- * + This template uses obdev's shared VID/PID pair: 0x16c0/0x5dc.
+ * *** IMPORTANT NOTE ***
- * + Use this VID/PID pair ONLY if you understand the implications!
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
  */
-#define  USB_CFG_DEVICE_ID       0xdc, 0x05
+#define  USB_CFG_DEVICE_ID       0xdc, 0x05 /* = 0x05dc = 1500 */
 /* This is the ID of the product, low byte first. It is interpreted in the
  * scope of the vendor ID. If you have registered your own VID with usb.org
  * or if you have licensed a PID from somebody else, define it here. Otherwise
- * you use obdev's free shared VID/PID pair. Be sure to read the rules in
+ * you may use one of obdev's free shared VID/PID pairs. See the file
- * USBID-License.txt!
+ * USB-IDs-for-free.txt for details!
- * + This template uses obdev's shared VID/PID pair: 0x16c0/0x5dc.
+ * *** IMPORTANT NOTE ***
- * + Use this VID/PID pair ONLY if you understand the implications!
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
  */
 #define USB_CFG_DEVICE_VERSION  0x00, 0x01
 /* Version number of the device: Minor number first, then major number.
@@ -230,14 +248,14 @@ section at the end of this file).
  * are interpreted as Unicode (UTF-16) entities.
  * If you don't want a vendor name string, undefine these macros.
  * ALWAYS define a vendor name containing your Internet domain name if you use
- * obdev's free shared VID/PID pair. See the file USBID-License.txt for
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
  * details.
  */
 #define USB_CFG_DEVICE_NAME     'T', 'e', 'm', 'p', 'l', 'a', 't', 'e'
 #define USB_CFG_DEVICE_NAME_LEN 8
 /* Same as above for the device name. If you don't want a device name, undefine
- * the macros. See the file USBID-License.txt before you assign a name if you
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
- * use a shared VID/PID.
+ * you use a shared VID/PID.
  */
 /*#define USB_CFG_SERIAL_NUMBER   'N', 'o', 'n', 'e' */
 /*#define USB_CFG_SERIAL_NUMBER_LEN   0 */
@@ -337,6 +355,15 @@ section at the end of this file).
 #define USB_CFG_DESCR_PROPS_HID_REPORT              0
 #define USB_CFG_DESCR_PROPS_UNKNOWN                 0
 
+
+#define usbMsgPtr_t unsigned short
+/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
+ * a scalar type here because gcc generates slightly shorter code for scalar
+ * arithmetics than for pointer arithmetics. Remove this define for backward
+ * type compatibility or define it to an 8 bit type if you use data in RAM only
+ * and all RAM is below 256 bytes (tiny memory model in IAR CC).
+ */
+
 /* ----------------------- Optional MCU Description ------------------------ */
 
 /* The following configurations have working defaults in usbdrv.h. You
@@ -352,6 +379,6 @@ section at the end of this file).
 /* #define USB_INTR_ENABLE_BIT     INT0 */
 /* #define USB_INTR_PENDING        GIFR */
 /* #define USB_INTR_PENDING_BIT    INTF0 */
-/* #define USB_INTR_VECTOR         SIG_INTERRUPT0 */
+/* #define USB_INTR_VECTOR         INT0_vect */
 
 #endif /* __usbconfig_h_included__ */

avr/usbload/usbdrv/usbdrv.c

@@ -5,10 +5,8 @@
  * Tabsize: 4
  * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbdrv.c 740 2009-04-13 18:23:31Z cs $
  */
 
-#include "usbportability.h"
 #include "usbdrv.h"
 #include "oddebug.h"
 
@@ -45,7 +43,7 @@ uchar       usbCurrentDataToken;/* when we check data toggling to ignore duplica
 #endif
 
 /* USB status registers / not shared with asm code */
-uchar               *usbMsgPtr;     /* data to transmit next -- ROM or RAM address */
+usbMsgPtr_t         usbMsgPtr;      /* data to transmit next -- ROM or RAM address */
 static usbMsgLen_t  usbMsgLen = USB_NO_MSG; /* remaining number of bytes */
 static uchar        usbMsgFlags;    /* flag values see below */
 
@@ -67,7 +65,7 @@ optimizing hints:
 #if USB_CFG_DESCR_PROPS_STRING_0 == 0
 #undef USB_CFG_DESCR_PROPS_STRING_0
 #define USB_CFG_DESCR_PROPS_STRING_0    sizeof(usbDescriptorString0)
-PROGMEM char usbDescriptorString0[] = { /* language descriptor */
+PROGMEM const char usbDescriptorString0[] = { /* language descriptor */
     4,          /* sizeof(usbDescriptorString0): length of descriptor in bytes */
     3,          /* descriptor type */
     0x09, 0x04, /* language index (0x0409 = US-English) */
@@ -77,7 +75,7 @@ PROGMEM char usbDescriptorString0[] = { /* language descriptor */
 #if USB_CFG_DESCR_PROPS_STRING_VENDOR == 0 && USB_CFG_VENDOR_NAME_LEN
 #undef USB_CFG_DESCR_PROPS_STRING_VENDOR
 #define USB_CFG_DESCR_PROPS_STRING_VENDOR   sizeof(usbDescriptorStringVendor)
-PROGMEM int  usbDescriptorStringVendor[] = {
+PROGMEM const int  usbDescriptorStringVendor[] = {
     USB_STRING_DESCRIPTOR_HEADER(USB_CFG_VENDOR_NAME_LEN),
     USB_CFG_VENDOR_NAME
 };
@@ -86,7 +84,7 @@ PROGMEM int  usbDescriptorStringVendor[] = {
 #if USB_CFG_DESCR_PROPS_STRING_PRODUCT == 0 && USB_CFG_DEVICE_NAME_LEN
 #undef USB_CFG_DESCR_PROPS_STRING_PRODUCT
 #define USB_CFG_DESCR_PROPS_STRING_PRODUCT   sizeof(usbDescriptorStringDevice)
-PROGMEM int  usbDescriptorStringDevice[] = {
+PROGMEM const int  usbDescriptorStringDevice[] = {
     USB_STRING_DESCRIPTOR_HEADER(USB_CFG_DEVICE_NAME_LEN),
     USB_CFG_DEVICE_NAME
 };
@@ -95,7 +93,7 @@ PROGMEM int  usbDescriptorStringDevice[] = {
 #if USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER == 0 && USB_CFG_SERIAL_NUMBER_LEN
 #undef USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
 #define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    sizeof(usbDescriptorStringSerialNumber)
-PROGMEM int usbDescriptorStringSerialNumber[] = {
+PROGMEM const int usbDescriptorStringSerialNumber[] = {
     USB_STRING_DESCRIPTOR_HEADER(USB_CFG_SERIAL_NUMBER_LEN),
     USB_CFG_SERIAL_NUMBER
 };
@@ -108,7 +106,7 @@ PROGMEM int usbDescriptorStringSerialNumber[] = {
 #if USB_CFG_DESCR_PROPS_DEVICE == 0
 #undef USB_CFG_DESCR_PROPS_DEVICE
 #define USB_CFG_DESCR_PROPS_DEVICE  sizeof(usbDescriptorDevice)
-PROGMEM char usbDescriptorDevice[] = {    /* USB device descriptor */
+PROGMEM const char usbDescriptorDevice[] = {    /* USB device descriptor */
     18,         /* sizeof(usbDescriptorDevice): length of descriptor in bytes */
     USBDESCR_DEVICE,        /* descriptor type */
     0x10, 0x01,             /* USB version supported */
@@ -139,7 +137,7 @@ PROGMEM char usbDescriptorDevice[] = {    /* USB device descriptor */
 #if USB_CFG_DESCR_PROPS_CONFIGURATION == 0
 #undef USB_CFG_DESCR_PROPS_CONFIGURATION
 #define USB_CFG_DESCR_PROPS_CONFIGURATION   sizeof(usbDescriptorConfiguration)
-PROGMEM char usbDescriptorConfiguration[] = {    /* USB configuration descriptor */
+PROGMEM const char usbDescriptorConfiguration[] = {    /* USB configuration descriptor */
     9,          /* sizeof(usbDescriptorConfiguration): length of descriptor in bytes */
     USBDESCR_CONFIG,    /* descriptor type */
     18 + 7 * USB_CFG_HAVE_INTRIN_ENDPOINT + 7 * USB_CFG_HAVE_INTRIN_ENDPOINT3 +
@@ -149,9 +147,9 @@ PROGMEM char usbDescriptorConfiguration[] = {    /* USB configuration descriptor
     1,          /* index of this configuration */
     0,          /* configuration name string index */
 #if USB_CFG_IS_SELF_POWERED
-    USBATTR_SELFPOWER,      /* attributes */
+    (1 << 7) | USBATTR_SELFPOWER,       /* attributes */
 #else
-    (char)USBATTR_BUSPOWER, /* attributes */
+    (1 << 7),                           /* attributes */
 #endif
     USB_CFG_MAX_BUS_POWER/2,            /* max USB current in 2mA units */
 /* interface descriptor follows inline: */
@@ -184,7 +182,7 @@ PROGMEM char usbDescriptorConfiguration[] = {    /* USB configuration descriptor
 #if USB_CFG_HAVE_INTRIN_ENDPOINT3   /* endpoint descriptor for endpoint 3 */
     7,          /* sizeof(usbDescrEndpoint) */
     USBDESCR_ENDPOINT,  /* descriptor type = endpoint */
-    (char)0x83, /* IN endpoint number 1 */
+    (char)(0x80 | USB_CFG_EP3_NUMBER), /* IN endpoint number 3 */
     0x03,       /* attrib: Interrupt endpoint */
     8, 0,       /* maximum packet size */
     USB_CFG_INTR_POLL_INTERVAL, /* in ms */
@@ -301,7 +299,7 @@ USB_PUBLIC void usbSetInterrupt3(uchar *data, uchar len)
             len = usbFunctionDescriptor(rq);        \
         }else{                                      \
             len = USB_PROP_LENGTH(cfgProp);         \
-            usbMsgPtr = (uchar *)(staticName);      \
+            usbMsgPtr = (usbMsgPtr_t)(staticName);  \
         }                                           \
     }
 
@@ -361,7 +359,8 @@ uchar       flags = USB_FLG_MSGPTR_IS_ROM;
  */
 static inline usbMsgLen_t usbDriverSetup(usbRequest_t *rq)
 {
-uchar   len  = 0, *dataPtr = usbTxBuf + 9;  /* there are 2 bytes free space at the end of the buffer */
+usbMsgLen_t len = 0;
+uchar   *dataPtr = usbTxBuf + 9;    /* there are 2 bytes free space at the end of the buffer */
 uchar   value = rq->wValue.bytes[0];
 #if USB_CFG_IMPLEMENT_HALT
 uchar   index = rq->wIndex.bytes[0];
@@ -408,7 +407,7 @@ uchar   index = rq->wIndex.bytes[0];
     SWITCH_DEFAULT                          /* 7=SET_DESCRIPTOR, 12=SYNC_FRAME */
         /* Should we add an optional hook here? */
     SWITCH_END
-    usbMsgPtr = dataPtr;
+    usbMsgPtr = (usbMsgPtr_t)dataPtr;
 skipMsgPtrAssignment:
     return len;
 }
@@ -498,7 +497,8 @@ static uchar usbDeviceRead(uchar *data, uchar len)
         }else
 #endif
         {
-            uchar i = len, *r = usbMsgPtr;
+            uchar i = len;
+            usbMsgPtr_t r = usbMsgPtr;
             if(usbMsgFlags & USB_FLG_MSGPTR_IS_ROM){    /* ROM data */
                 do{
                     uchar c = USB_READ_FLASH(r);    /* assign to char size variable to enforce byte ops */
@@ -507,7 +507,8 @@ static uchar usbDeviceRead(uchar *data, uchar len)
                 }while(--i);
             }else{  /* RAM data */
                 do{
-                    *data++ = *r++;
+                    *data++ = *((uchar *)r);
+                    r++;
                 }while(--i);
             }
             usbMsgPtr = r;
@@ -557,6 +558,8 @@ uchar           isReset = !notResetState;
         USB_RESET_HOOK(isReset);
         wasReset = isReset;
     }
+#else
+    notResetState = notResetState;  // avoid compiler warning
 #endif
 }
 

avr/usbload/usbdrv/usbdrv.h

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbdrv.h 748 2009-04-15 15:05:07Z cs $
  */
 
 #ifndef __usbdrv_h_included__
@@ -105,9 +104,9 @@ interrupt routine.
 Interrupt latency:
 The application must ensure that the USB interrupt is not disabled for more
 than 25 cycles (this is for 12 MHz, faster clocks allow longer latency).
-This implies that all interrupt routines must either be declared as "INTERRUPT"
+This implies that all interrupt routines must either have the "ISR_NOBLOCK"
-instead of "SIGNAL" (see "avr/signal.h") or that they are written in assembler
+attribute set (see "avr/interrupt.h") or be written in assembler with "sei"
-with "sei" as the first instruction.
+as the first instruction.
 
 Maximum interrupt duration / CPU cycle consumption:
 The driver handles all USB communication during the interrupt service
@@ -122,7 +121,7 @@ USB messages, even if they address another (low-speed) device on the same bus.
 /* --------------------------- Module Interface ---------------------------- */
 /* ------------------------------------------------------------------------- */
 
-#define USBDRV_VERSION  20090415
+#define USBDRV_VERSION  20121206
 /* This define uniquely identifies a driver version. It is a decimal number
  * constructed from the driver's release date in the form YYYYMMDD. If the
  * driver's behavior or interface changes, you can use this constant to
@@ -163,11 +162,24 @@ USB messages, even if they address another (low-speed) device on the same bus.
  */
 #define USB_NO_MSG  ((usbMsgLen_t)-1)   /* constant meaning "no message" */
 
+#ifndef usbMsgPtr_t
+#define usbMsgPtr_t uchar *
+#endif
+/* Making usbMsgPtr_t a define allows the user of this library to define it to
+ * an 8 bit type on tiny devices. This reduces code size, especially if the
+ * compiler supports a tiny memory model.
+ * The type can be a pointer or scalar type, casts are made where necessary.
+ * Although it's paradoxical, Gcc 4 generates slightly better code for scalar
+ * types than for pointers.
+ */
+
 struct usbRequest;  /* forward declaration */
 
 USB_PUBLIC void usbInit(void);
 /* This function must be called before interrupts are enabled and the main
- * loop is entered.
+ * loop is entered. We exepct that the PORT and DDR bits for D+ and D- have
+ * not been changed from their default status (which is 0). If you have changed
+ * them, set both back to 0 (configure them as input with no internal pull-up).
  */
 USB_PUBLIC void usbPoll(void);
 /* This function must be called at regular intervals from the main loop.
@@ -176,7 +188,7 @@ USB_PUBLIC void usbPoll(void);
  * Please note that debug outputs through the UART take ~ 0.5ms per byte
  * at 19200 bps.
  */
-extern uchar *usbMsgPtr;
+extern usbMsgPtr_t usbMsgPtr;
 /* This variable may be used to pass transmit data to the driver from the
  * implementation of usbFunctionWrite(). It is also used internally by the
  * driver for standard control requests.
@@ -388,13 +400,13 @@ extern volatile schar   usbRxLen;
  * about the various methods to define USB descriptors. If you do nothing,
  * the default descriptors will be used.
  */
-#define USB_PROP_IS_DYNAMIC     (1 << 14)
+#define USB_PROP_IS_DYNAMIC     (1u << 14)
 /* If this property is set for a descriptor, usbFunctionDescriptor() will be
  * used to obtain the particular descriptor. Data directly returned via
  * usbMsgPtr are FLASH data by default, combine (OR) with USB_PROP_IS_RAM to
  * return RAM data.
  */
-#define USB_PROP_IS_RAM         (1 << 15)
+#define USB_PROP_IS_RAM         (1u << 15)
 /* If this property is set for a descriptor, the data is read from RAM
  * memory instead of Flash. The property is used for all methods to provide
  * external descriptors.
@@ -448,43 +460,43 @@ extern volatile schar   usbRxLen;
 #ifndef __ASSEMBLER__
 extern
 #if !(USB_CFG_DESCR_PROPS_DEVICE & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 char usbDescriptorDevice[];
 
 extern
 #if !(USB_CFG_DESCR_PROPS_CONFIGURATION & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 char usbDescriptorConfiguration[];
 
 extern
 #if !(USB_CFG_DESCR_PROPS_HID_REPORT & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 char usbDescriptorHidReport[];
 
 extern
 #if !(USB_CFG_DESCR_PROPS_STRING_0 & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 char usbDescriptorString0[];
 
 extern
 #if !(USB_CFG_DESCR_PROPS_STRING_VENDOR & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 int usbDescriptorStringVendor[];
 
 extern
 #if !(USB_CFG_DESCR_PROPS_STRING_PRODUCT & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 int usbDescriptorStringDevice[];
 
 extern
 #if !(USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER & USB_PROP_IS_RAM)
-PROGMEM
+PROGMEM const
 #endif
 int usbDescriptorStringSerialNumber[];
 
@@ -511,22 +523,22 @@ int usbDescriptorStringSerialNumber[];
 #if !defined __ASSEMBLER__ && (!defined USB_CFG_VENDOR_ID || !defined USB_CFG_DEVICE_ID)
 #warning "You should define USB_CFG_VENDOR_ID and USB_CFG_DEVICE_ID in usbconfig.h"
 /* If the user has not defined IDs, we default to obdev's free IDs.
- * See USBID-License.txt for details.
+ * See USB-IDs-for-free.txt for details.
  */
 #endif
 
 /* make sure we have a VID and PID defined, byte order is lowbyte, highbyte */
 #ifndef USB_CFG_VENDOR_ID
-#   define  USB_CFG_VENDOR_ID   0xc0, 0x16  /* 5824 in dec, stands for VOTI */
+#   define  USB_CFG_VENDOR_ID   0xc0, 0x16  /* = 0x16c0 = 5824 = voti.nl */
 #endif
 
 #ifndef USB_CFG_DEVICE_ID
 #   if USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH
-#       define USB_CFG_DEVICE_ID    0xdf, 0x05  /* 1503 in dec, shared PID for HIDs */
+#       define USB_CFG_DEVICE_ID    0xdf, 0x05  /* = 0x5df = 1503, shared PID for HIDs */
 #   elif USB_CFG_INTERFACE_CLASS == 2
-#       define USB_CFG_DEVICE_ID    0xe1, 0x05  /* 1505 in dec, shared PID for CDC Modems */
+#       define USB_CFG_DEVICE_ID    0xe1, 0x05  /* = 0x5e1 = 1505, shared PID for CDC Modems */
 #   else
-#       define USB_CFG_DEVICE_ID    0xdc, 0x05  /* 1500 in dec, obdev's free PID */
+#       define USB_CFG_DEVICE_ID    0xdc, 0x05  /* = 0x5dc = 1500, obdev's free PID */
 #   endif
 #endif
 
@@ -716,7 +728,8 @@ typedef struct usbRequest{
 #define USBDESCR_HID_REPORT     0x22
 #define USBDESCR_HID_PHYS       0x23
 
-#define USBATTR_BUSPOWER        0x80
+//#define USBATTR_BUSPOWER        0x80  // USB 1.1 does not define this value any more
+#define USBATTR_BUSPOWER        0
 #define USBATTR_SELFPOWER       0x40
 #define USBATTR_REMOTEWAKE      0x20
 

avr/usbload/usbdrv/usbdrvasm.S

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id: usbdrvasm.S 740 2009-04-13 18:23:31Z cs $
  */
 
 /*
@@ -57,7 +56,11 @@ the file appropriate for the given clock rate.
 #else /* __IAR_SYSTEMS_ASM__ */
 
 #   ifndef USB_INTR_VECTOR /* default to hardware interrupt INT0 */
-#       define USB_INTR_VECTOR  SIG_INTERRUPT0
+#       ifdef INT0_vect
+#           define USB_INTR_VECTOR  INT0_vect       // this is the "new" define for the vector
+#       else
+#           define USB_INTR_VECTOR  SIG_INTERRUPT0  // this is the "old" vector
+#       endif
 #   endif
     .text
     .global USB_INTR_VECTOR
@@ -139,16 +142,93 @@ RTMODEL "__rt_version", "3"
 
 #endif
 
-; extern unsigned usbCrc16(unsigned char *data, unsigned char len);
+#if USB_USE_FAST_CRC
-; data: r24/25
+
-; len: r22
+; This implementation is faster, but has bigger code size
+; Thanks to Slawomir Fras (BoskiDialer) for this code!
+; It implements the following C pseudo-code:
+; unsigned table(unsigned char x)
+; {
+; unsigned    value;
+; 
+;     value = (unsigned)x << 6;
+;     value ^= (unsigned)x << 7;
+;     if(parity(x))
+;         value ^= 0xc001;
+;     return value;
+; }
+; unsigned usbCrc16(unsigned char *argPtr, unsigned char argLen)
+; {
+; unsigned crc = 0xffff;
+; 
+;     while(argLen--)
+;         crc = table(lo8(crc) ^ *argPtr++) ^ hi8(crc);
+;     return ~crc;
+; }
+
+; extern unsigned usbCrc16(unsigned char *argPtr, unsigned char argLen);
+;   argPtr  r24+25 / r16+r17
+;   argLen  r22 / r18
 ; temp variables:
-;   r18: data byte
+;   byte    r18 / r22
-;   r19: bit counter
+;   scratch r23
-;   r20/21: polynomial
+;   resCrc  r24+r25 / r16+r17
-;   r23: scratch
+;   ptr     X / Z
-;   r24/25: crc-sum
+usbCrc16:
-;   r26/27=X: ptr
+    mov     ptrL, argPtrL
+    mov     ptrH, argPtrH
+    ldi     resCrcL, 0xFF
+    ldi     resCrcH, 0xFF
+    rjmp    usbCrc16LoopTest
+usbCrc16ByteLoop:
+    ld      byte, ptr+
+    eor     resCrcL, byte   ; resCrcL is now 'x' in table()
+    mov     byte, resCrcL   ; compute parity of 'x'
+    swap    byte
+    eor     byte, resCrcL
+    mov     scratch, byte
+    lsr     byte
+    lsr     byte
+    eor     byte, scratch
+    inc     byte
+    lsr     byte
+    andi    byte, 1         ; byte is now parity(x)
+    mov     scratch, resCrcL
+    mov     resCrcL, resCrcH
+    eor     resCrcL, byte   ; low byte of if(parity(x)) value ^= 0xc001;
+    neg     byte
+    andi    byte, 0xc0
+    mov     resCrcH, byte   ; high byte of if(parity(x)) value ^= 0xc001;
+    clr     byte
+    lsr     scratch
+    ror     byte
+    eor     resCrcH, scratch
+    eor     resCrcL, byte
+    lsr     scratch
+    ror     byte
+    eor     resCrcH, scratch
+    eor     resCrcL, byte
+usbCrc16LoopTest:
+    subi    argLen, 1
+    brsh    usbCrc16ByteLoop
+    com     resCrcL
+    com     resCrcH
+    ret
+
+#else   /* USB_USE_FAST_CRC */
+
+; This implementation is slower, but has less code size
+;
+; extern unsigned usbCrc16(unsigned char *argPtr, unsigned char argLen);
+;   argPtr  r24+25 / r16+r17
+;   argLen  r22 / r18
+; temp variables:
+;   byte    r18 / r22
+;   bitCnt  r19
+;   poly    r20+r21
+;   scratch r23
+;   resCrc  r24+r25 / r16+r17
+;   ptr     X / Z
 usbCrc16:
     mov     ptrL, argPtrL
     mov     ptrH, argPtrH
@@ -156,27 +236,30 @@ usbCrc16:
     ldi     resCrcH, 0
     ldi     polyL, lo8(0xa001)
     ldi     polyH, hi8(0xa001)
-    com     argLen      ; argLen = -argLen - 1
+    com     argLen      ; argLen = -argLen - 1: modified loop to ensure that carry is set
-crcByteLoop:
+    ldi     bitCnt, 0   ; loop counter with starnd condition = end condition
-    subi    argLen, -1
+    rjmp    usbCrcLoopEntry
-    brcc    crcReady    ; modified loop to ensure that carry is set below
+usbCrcByteLoop:
     ld      byte, ptr+
-    ldi     bitCnt, -8  ; strange loop counter to ensure that carry is set where we need it
     eor     resCrcL, byte
-crcBitLoop:
+usbCrcBitLoop:
-    ror     resCrcH     ; carry is always set here
+    ror     resCrcH     ; carry is always set here (see brcs jumps to here)
     ror     resCrcL
-    brcs    crcNoXor
+    brcs    usbCrcNoXor
     eor     resCrcL, polyL
     eor     resCrcH, polyH
-crcNoXor:
+usbCrcNoXor:
-    subi    bitCnt, -1
+    subi    bitCnt, 224 ; (8 * 224) % 256 = 0; this loop iterates 8 times
-    brcs    crcBitLoop
+    brcs    usbCrcBitLoop
-    rjmp    crcByteLoop
+usbCrcLoopEntry:
-crcReady:
+    subi    argLen, -1
+    brcs    usbCrcByteLoop
+usbCrcReady:
     ret
 ; Thanks to Reimar Doeffinger for optimizing this CRC routine!
 
+#endif /* USB_USE_FAST_CRC */
+
 ; extern unsigned usbCrc16Append(unsigned char *data, unsigned char len);
 usbCrc16Append:
     rcall   usbCrc16
@@ -277,7 +360,11 @@ usbMFTimeout:
 ;----------------------------------------------------------------------------
 
 #ifndef USB_CFG_CLOCK_KHZ
-#   define USB_CFG_CLOCK_KHZ 12000
+#   ifdef F_CPU
+#       define USB_CFG_CLOCK_KHZ (F_CPU/1000)
+#   else
+#       error "USB_CFG_CLOCK_KHZ not defined in usbconfig.h and no F_CPU set!"
+#   endif
 #endif
 
 #if USB_CFG_CHECK_CRC   /* separate dispatcher for CRC type modules */

avr/usbload/usbdrv/usbdrvasm.asm

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2006 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id$
  */
 
 /*

avr/usbload/usbdrv/usbdrvasm12.inc

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbdrvasm12.inc 740 2009-04-13 18:23:31Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the

avr/usbload/usbdrv/usbdrvasm128.inc

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2008 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbdrvasm128.inc 740 2009-04-13 18:23:31Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the
@@ -31,8 +30,9 @@ limitations:
 They typical range is 14.5 MHz and most AVRs can actually reach this rate.
 (2) Writing EEPROM and Flash may be unreliable (short data lifetime) since
 the write procedure is timed from the RC oscillator.
-(3) End Of Packet detection is between bit 0 and bit 1 where the EOP condition
+(3) End Of Packet detection (SE0) should be in bit 1, bit it is only checked
-may not be reliable when a hub is used. It should be in bit 1.
+if bits 0 and 1 both read as 0 on D- and D+ read as 0 in the middle. This may
+cause problems with old hubs which delay SE0 by up to one cycle.
 (4) Code size is much larger than that of the other modules.
 
 Since almost all of this code is timing critical, don't change unless you
@@ -217,8 +217,10 @@ unstuff0s:
     ifioclr USBIN, USBMINUS     ;[00]
     ifioset USBIN, USBPLUS      ;[01]
     rjmp    bit0IsClr           ;[02] executed if first expr false or second true
-jumpToSe0AndStore:
+se0AndStore:                    ; executed only if both bits 0
-    rjmp    se0AndStore         ;[03] executed only if both bits 0
+    st      y+, x1              ;[15/17] cycles after start of byte
+    rjmp    se0                 ;[17/19]
+
 bit0IsClr:
     ifrset  phase, USBMINUS     ;[04] check phase only if D- changed
     lpm                         ;[05]
@@ -228,7 +230,7 @@ bit1AfterClr:
     andi    phase, USBMASK      ;[08]
     ifioset USBIN, USBMINUS     ;[09] <--- sample 1
     rjmp    bit1IsSet           ;[10]
-    breq    jumpToSe0AndStore   ;[11]
+    breq    se0AndStore         ;[11] if D- was 0 in bits 0 AND 1 and D+ was 0 in between, we have SE0
     andi    shift, ~(7 << 1)    ;[12]
     in      phase, USBIN        ;[13] <- phase
     breq    unstuff1c           ;[14]
@@ -355,10 +357,6 @@ unstuff7c:
     nop                         ;[59]
     rjmp    bit7IsSet           ;[60]
 
-se0AndStore:
-    st      y+, x1              ;[15/17] cycles after start of byte
-    rjmp    se0                 ;[17/19]
-
 bit7IsClr:
     ifrset  phase, USBMINUS     ;[62] check phase only if D- changed
     lpm                         ;[63]
@@ -391,25 +389,24 @@ bit0IsSet:
     in      phase, USBIN        ;[06] <- phase (one cycle too late)
     ori     shift, 1 << 0       ;[07]
 bit1AfterSet:
-    andi    phase, USBMASK      ;[08]
+    andi    shift, ~(7 << 1)    ;[08] compensated by "ori shift, 1<<1" if bit1IsClr
     ifioclr USBIN, USBMINUS     ;[09] <--- sample 1
     rjmp    bit1IsClr           ;[10]
-    andi    shift, ~(7 << 1)    ;[11]
+    breq    unstuff1s           ;[11]
-    breq    unstuff1s           ;[12]
+    nop2                        ;[12] do not check for SE0 if bit 0 was 1
-    in      phase, USBIN        ;[13] <- phase
+    in      phase, USBIN        ;[14] <- phase (one cycle too late)
-    nop                         ;[14]
     rjmp    bit2AfterSet        ;[15]
 unstuff1s:
-    in      phase, USBIN        ;[14] <- phase (one cycle too late)
+    in      phase, USBIN        ;[13] <- phase
-    andi    fix, ~(1 << 1)      ;[15]
+    andi    fix, ~(1 << 1)      ;[14]
-    nop2                        ;[08]
+    lpm                         ;[07]
     nop2                        ;[10]
 bit1IsClr:
     ifrset  phase, USBMINUS     ;[12] check phase only if D- changed
     lpm                         ;[13]
     in      phase, USBIN        ;[14] <- phase (one cycle too late)
-    breq    se0AndStore         ;[15] if we come from unstuff1s, Z bit is never set
+    ori     shift, 1 << 1       ;[15]
-    ori     shift, 1 << 1       ;[16]
+    nop                         ;[16]
 bit2AfterClr:
     ifioset USBIN, USBMINUS     ;[17] <--- sample 2
     rjmp    bit2IsSet           ;[18]

avr/usbload/usbdrv/usbdrvasm15.inc

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id: usbdrvasm15.inc 740 2009-04-13 18:23:31Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the

avr/usbload/usbdrv/usbdrvasm16.inc

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id: usbdrvasm16.inc 740 2009-04-13 18:23:31Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the
@@ -117,12 +116,15 @@ haveTwoBitsK:
 ; Receiver loop (numbers in brackets are cycles within byte after instr)
 ;----------------------------------------------------------------------------
 
+; duration of unstuffing code should be 10.66666667 cycles. We adjust "leap"
+; accordingly to approximate this value in the long run.
+
 unstuff6:
     andi    x2, USBMASK ;[03]
     ori     x3, 1<<6    ;[04] will not be shifted any more
     andi    shift, ~0x80;[05]
     mov     x1, x2      ;[06] sampled bit 7 is actually re-sampled bit 6
-    subi    leap, 3     ;[07] since this is a short (10 cycle) bit, enforce leap bit
+    subi    leap, -1    ;[07] total duration = 11 bits -> subtract 1/3
     rjmp    didUnstuff6 ;[08]
 
 unstuff7:
@@ -130,7 +132,7 @@ unstuff7:
     in      x2, USBIN   ;[00] [10]  re-sample bit 7
     andi    x2, USBMASK ;[01]
     andi    shift, ~0x80;[02]
-    subi    leap, 3     ;[03] since this is a short (10 cycle) bit, enforce leap bit
+    subi    leap, 2     ;[03] total duration = 10 bits -> add 1/3
     rjmp    didUnstuff7 ;[04]
 
 unstuffEven:
@@ -139,8 +141,8 @@ unstuffEven:
     andi    shift, ~0x80;[01]
     andi    x1, USBMASK ;[02]
     breq    se0         ;[03]
-    subi    leap, 3     ;[04] since this is a short (10 cycle) bit, enforce leap bit
+    subi    leap, -1    ;[04] total duration = 11 bits -> subtract 1/3
-    nop                 ;[05]
+    nop2                ;[05]
     rjmp    didUnstuffE ;[06]
 
 unstuffOdd:
@@ -149,8 +151,8 @@ unstuffOdd:
     andi    shift, ~0x80;[01]
     andi    x2, USBMASK ;[02]
     breq    se0         ;[03]
-    subi    leap, 3     ;[04] since this is a short (10 cycle) bit, enforce leap bit
+    subi    leap, -1    ;[04] total duration = 11 bits -> subtract 1/3
-    nop                 ;[05]
+    nop2                ;[05]
     rjmp    didUnstuffO ;[06]
 
 rxByteLoop:

avr/usbload/usbdrv/usbdrvasm165.inc

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id: usbdrvasm165.inc 740 2009-04-13 18:23:31Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the

avr/usbload/usbdrv/usbdrvasm18-crc.inc

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2008 by Lukas Schrittwieser and OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id: usbdrvasm18-crc.inc 740 2009-04-13 18:23:31Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the

avr/usbload/usbdrv/usbdrvasm20.inc

@@ -6,7 +6,6 @@
  * Tabsize: 4
  * Copyright: (c) 2008 by Jeroen Benschop and OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id: usbdrvasm20.inc 740 2009-04-13 18:23:31Z cs $
  */
 
 /* Do not link this file! Link usbdrvasm.S instead, which includes the

avr/usbload/usbdrv/usbportability.h

@@ -5,7 +5,6 @@
  * Tabsize: 4
  * Copyright: (c) 2008 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbportability.h 740 2009-04-13 18:23:31Z cs $
  */
 
 /*
@@ -125,7 +124,11 @@ static inline void  sei(void)
 #   include <avr/pgmspace.h>
 #endif
 
-#define USB_READ_FLASH(addr)    pgm_read_byte(addr)
+#if USB_CFG_DRIVER_FLASH_PAGE
+#   define USB_READ_FLASH(addr)    pgm_read_byte_far(((long)USB_CFG_DRIVER_FLASH_PAGE << 16) | (long)(addr))
+#else
+#   define USB_READ_FLASH(addr)    pgm_read_byte(addr)
+#endif
 
 #define macro   .macro
 #define endm    .endm

avr/usbload/util.c

@@ -0,0 +1,145 @@
+/*
+ * =====================================================================================
+ *
+ * ________        .__        __    ________               ____  ________
+ * \_____  \  __ __|__| ____ |  | __\______ \   _______  _/_   |/  _____/
+ *  /  / \  \|  |  \  |/ ___\|  |/ / |    |  \_/ __ \  \/ /|   /   __  \
+ * /   \_/.  \  |  /  \  \___|    <  |    `   \  ___/\   / |   \  |__\  \
+ * \_____\ \_/____/|__|\___  >__|_ \/_______  /\___  >\_/  |___|\_____  /
+ *        \__>             \/     \/        \/     \/                 \/
+ *
+ *                                  www.optixx.org
+ *
+ *
+ *        Version:  1.0
+ *        Created:  07/21/2009 03:32:16 PM
+ *         Author:  david@optixx.org
+ *
+ * =====================================================================================
+ */
+
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+
+uint8_t *util_strupper(uint8_t * s)
+{
+    uint8_t *p;
+    for (p = s; *p != '\0'; p++)
+        if (*p >= 'a' && *p <= 'z')
+            *p += 'A' - 'a';
+    return s;
+}
+
+uint8_t *util_strlower(uint8_t * s)
+{
+    uint8_t *p;
+    for (p = s; *p != '\0'; p++)
+        if (*p >= 'A' && *p <= 'Z')
+            *p += 'a' - 'A';
+    return s;
+}
+
+void util_chomp(uint8_t * s)
+{
+    uint16_t len;
+
+    len = strlen((char *) s);
+    if (len >= 2 && s[len - 1] == '\n' && s[len - 2] == '\r')
+        s[len - 2] = '\0';
+    else if (len >= 1 && (s[len - 1] == '\n' || s[len - 1] == '\r'))
+        s[len - 1] = '\0';
+}
+
+void util_trim(uint8_t * s)
+{
+    uint8_t *p = s;
+    uint8_t *q;
+    /*
+     * skip leading whitespace 
+     */
+    while (*p == ' ' || *p == '\t' || *p == '\r' || *p == '\n')
+        p++;
+    /*
+     * now p points at the first non-whitespace uint8_tacter 
+     */
+
+    if (*p == '\0') {
+        /*
+         * only whitespace 
+         */
+        *s = '\0';
+        return;
+    }
+
+    q = s + strlen((char *) s);
+    /*
+     * skip trailing whitespace 
+     */
+    /*
+     * we have found p < q such that *p is non-whitespace, so this loop terminates with q >= p 
+     */
+    do
+        q--;
+    while (*q == ' ' || *q == '\t' || *q == '\r' || *q == '\n');
+
+    /*
+     * now q points at the last non-whitespace uint8_tacter 
+     */
+    /*
+     * cut off trailing whitespace 
+     */
+    *++q = '\0';
+
+    /*
+     * move to string 
+     */
+    memmove(s, p, q + 1 - p);
+}
+
+uint32_t util_sscandec(const uint8_t * s)
+{
+    uint32_t result;
+    if (*s == '\0')
+        return -1;
+    result = 0;
+    for (;;) {
+        if (*s >= '0' && *s <= '9')
+            result = 10 * result + *s - '0';
+        else if (*s == '\0')
+            return result;
+        else
+            return -1;
+        s++;
+    }
+}
+
+uint32_t util_sscanhex(const uint8_t * s)
+{
+    int32_t result;
+    if (*s == '\0')
+        return -1;
+    result = 0;
+    for (;;) {
+        if (*s >= '0' && *s <= '9')
+            result = 16 * result + *s - '0';
+        else if (*s >= 'A' && *s <= 'F')
+            result = 16 * result + *s - 'A' + 10;
+        else if (*s >= 'a' && *s <= 'f')
+            result = 16 * result + *s - 'a' + 10;
+        else if (*s == '\0')
+            return result;
+        else
+            return -1;
+        s++;
+    }
+}
+
+uint8_t util_sscanbool(const uint8_t * s)
+{
+    if (*s == '0' && s[1] == '\0')
+        return 0;
+    if (*s == '1' && s[1] == '\0')
+        return 1;
+    return -1;
+}

avr/usbload/util.h

@@ -0,0 +1,32 @@
+/*
+ * =====================================================================================
+ *
+ * ________        .__        __    ________               ____  ________
+ * \_____  \  __ __|__| ____ |  | __\______ \   _______  _/_   |/  _____/
+ *  /  / \  \|  |  \  |/ ___\|  |/ / |    |  \_/ __ \  \/ /|   /   __  \
+ * /   \_/.  \  |  /  \  \___|    <  |    `   \  ___/\   / |   \  |__\  \
+ * \_____\ \_/____/|__|\___  >__|_ \/_______  /\___  >\_/  |___|\_____  /
+ *        \__>             \/     \/        \/     \/                 \/
+ *
+ *                                  www.optixx.org
+ *
+ *
+ *        Version:  1.0
+ *        Created:  07/21/2009 03:32:16 PM
+ *         Author:  david@optixx.org
+ *
+ * =====================================================================================
+ */
+
+#ifndef __UTIL_H__
+#define __UTIL_H__
+
+uint8_t *util_strupper(uint8_t * s);
+uint8_t *util_strlower(uint8_t * s);
+void util_chomp(uint8_t * s);
+void util_trim(uint8_t * s);
+uint32_t util_sscandec(const uint8_t * s);
+uint32_t util_sscanhex(const uint8_t * s);
+uint8_t util_sscanbool(const uint8_t * s);
+
+#endif

avr/usbload/watchdog.c

@@ -28,4 +28,3 @@ void wdt_init(void)
 
     return;
 }
-

avr/usbload/watchdog.h

@@ -27,7 +27,7 @@
 #define __WATCHDOG_H__
 
 
-void wdt_init(void) __attribute__((naked)) __attribute__((section(".init3")));
+void wdt_init(void) __attribute__ ((naked)) __attribute__ ((section(".init3")));
 
 #define soft_reset()        \
 do                          \
@@ -39,4 +39,3 @@ do                          \
 } while(0)
 
 #endif
-

done.txt

@@ -0,0 +1,10 @@
+x 2009-10-13 Send PCB to seeed
+x 2009-10-13 RS232 cable add programm header and sio lines
+x 2009-10-13 Assemble No. 006 & No. 007
+x 2009-10-13 Flash all cartridge with latest firmware and bootloader
+x 2009-10-13 Bootloader lockbits
+x 2009-10-13 Rework No. 002
+x 2009-10-13 Package for Quickdev16
+x 2009-10-13 Add struct for usb and communcations flags
+x 2009-10-13 Mail snega2usb about OEM
+x 2009-10-13 Email to seeed about the retour package

files/Quickdev16_1.5_sdcard.txt

@@ -0,0 +1,45 @@
+--------------------------------
+SDcard Board
+--------------------------------
+Connector 
+
+1  DO   -> 7  
+2  GND  -> 6 
+3  VCC  -> 4
+4  CS   -> 1
+5  DI   -> 2
+6  CLK  -> 5
+-
+SDcard
+------------------\
+|                  \
+| 8 7 6 5 4 3 2 1 9 |
+|                   |
+
+1 CS
+2 CMD/DI
+3 GND
+4 VCC
+5 CLK/SCLK
+6 GND
+7 DAT/DO
+8 --
+9 --	
+
+
+--------------------------------
+Quickdev Header
+--------------------------------
+top/usb
+1 GND                -> GND
+2 ISP RST  - RESET   -      
+3 ISP SCK  - PB7     - CLK
+4 ISP MISO - PB6     - DI
+5 ISP MOSI - PB5     - DO
+6 MMC CS   - PB4     - CS 
+7 VCC                -> VCC 
+
+
+
+#define SPI_DI				6		MISO
+#define SPI_DO				5		MOSI

files/Quickdev16_ascii_banner.txt

@@ -0,0 +1,29 @@
+________        .__        __    ________               ____  ________
+\_____  \  __ __|__| ____ |  | __\______ \   _______  _/_   |/  _____/
+ /  / \  \|  |  \  |/ ___\|  |/ / |    |  \_/ __ \  \/ /|   /   __  \
+/   \_/.  \  |  /  \  \___|    <  |    `   \  ___/\   / |   \  |__\  \
+\_____\ \_/____/|__|\___  >__|_ \/_______  /\___  >\_/  |___|\_____  /
+       \__>             \/     \/        \/     \/                 \/
+             ___.
+ __ __  _____\_ |__
+|  |  \/  ___/| __ \
+|  |  /\___ \ | \_\ \
+|____//____  >|___  /
+           \/     \/
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+